Yale Real Living YRD220 Technical specifications

1
P/N -220- - Rev FAYRD INST FUL
x4
x2
x3
Yale Real Living Touchscreen Deadbolt
®
Installation and Programming Instructions
(YRD220)
®
#8-32 x 5/16"
Machine screws
#7 wood & #8-32
machine x 20mm
Combination screws
M6x47mm
Long through bolt
Optional
Network Module

2
P/N -220- - Rev FAYRD INST FUL
Preparing Door

3
P/N -220- - Rev FAYRD INST FUL
O
x4
1
d faute
2-3/8" position
2-3/4" position
Installing Latch & Strike Plate
Press
Pull
optional
Bolt must be in retracted
(unlocked) position. Note
horizontal orientation of
mechanism.

4
P/N -220- - Rev FAYRD INST FUL
2Installing Touchscreen Escutcheon
Outside of DoorInside of Door
Bolt must be in retracted (unlocked)
position. Note horizontal orientation
of mechanism.

5
P/N -220- - Rev FAYRD INST FUL
x2
3Installing Interior Mounting Plate
Loosen screw to
remove cover.

4Attaching the Cable Assembly
6
P/N -220- - Rev FAYRD INST FUL

7
P/N -220- - Rev FAYRD INST FUL
x3
5Installing Interior Escutcheon

8
P/N -220- - Rev FAYRD INST FUL
3
Testing Operation
Bolt must be in retracted
(unlocked) position before
installing batteries.

9
P/N -220- - Rev FAYRD INST FUL
2
Testing Operation

10
P/N -220- - Rev FAYRD INST FUL
6
7Installing Batteries & Cover
Congratulations, you've installed the Yale Real Living Touchscreen Deadbolt (YRD220)!
®
Continue with Programming Instructions to customize your product.
Installing Optional Network Module
Tighten screw
to replace cover.
"Welcome to
Yale Real Living."

Programming Instructions
OR
Master Code must be created before any further programming.PIN
Max User Codes = 250 with Network Module. Max User Codes = 25 without.
Interior Escutcheon
Privacy
Mode
Button
Exterior Escutcheon
Speaker
"P" Key
(Return to Previous)
Lockout
Mode
Low Battery
Indicator
11
P/N -220- - Rev FAYRD INST FUL

1Creating a Master Code must be performed upon installation or after resettingPIN
the lock to factory default. Programming and use of lock is not possible until this
step has been successfully completed.
"Register Master
Code. Press the pound
key to continue."
"Enter a 4 to 8 digit
code followed byPIN
the pound key."
"Registered."
Enter 4-8
digit Master
Code.PIN
Press
Press
Creating Master CodePIN
12
P/N -220- - Rev FAYRD INST FUL

2Creating User CodesPIN
Master code must be created first.PIN
*Max user codes = 250 with Network Module. Max user codes = 25 without.
"Menu Mode,
enter number,
press the pound key
to continue."
Enter Master
codePIN
Press
Press
Press
Press
Press Press
Enter User number
(1-25) or (1-250)*
Press
Enter 4-8 digit codePIN
Press
Enter 4-8 digit codePIN
Press
(code flashes)
Adding more User Codes: To end programming:
Press
13
P/N -220- - Rev FAYRD INST FUL

14
P/N -220- - Rev FAYRD INST FUL
3
PIN Code Management (With Network Module - Up to 250 Users)
Master
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
Enter CodePIN
Press
Code Chart Duplicate if necessary
User Name
User Type PIN Code
Unlocking Door with CodePIN
User #

15
P/N -220- - Rev FAYRD INST FUL
When lock is reset to factory defaults all user codes
(including the Master code*) are deleted and allPIN
programming features are reset to original default
settings (see below).
1. Remove the battery cover and batteries.
2. Remove the interior escutcheon to access the
reset button.
3. The reset button (see image at right) is located
above the cable connector.PCB
4. While pressing the reset button (minimum of 3
seconds) reinstall batteries. Release reset button.
5. Replace battery cover.
Upon reset, Master Code creation is the onlyPIN
option available and must be performed prior to any
other programming of the lock.
Registration required*
Wrong Code Entry Limit 5 Times
One Touch Locking Enabled
Inside Indicator Light Disabled (Off)
Interior Escutcheon
Factory Settings
Resetting Lock to Factory Default
Settings Factory Setting
Master CodePIN
Automatic Re-lock Disabled
Volume Setting Enabled (Low)
Automatic Re-lock Time 30 Seconds
Shutdown Time 60 Seconds
*The Master code must be registered prior to any other programming ofPIN
the lock.

16
P/N -220- - Rev FAYRD INST FUL
All Code Lockout Mode: This feature is enabled by the Master code. When enabled, it restricts all user (except
Master) code access. When attempting to enter a code while the unit is in Lockout, the locked padlockPIN RED
will appear on the screen.
Automatic Re-lock Time: After a successful code entry and the unit unlocks, it will automatically re-lock after
thirty (30) seconds. This feature is only available when a Network Module is installed.
Inside Indicator Light: Located on the interior escutcheon. Shows active status (Locked) of lock and can be
enabled or disabled in the (Main Menu selection #3).Advanced Lock Settings
Language Setting Mode: Choosing English (1), Spanish (2) or French (3) becomes the (default) setting for the
lock's voice prompts.
Low Battery: When battery power is low, the Low Battery Warning indicator flashes . If battery power isRED
completely lost, use the cylinder key override.
Master Code: It must be createdPIN The Master code is used for programming and for feature settings.PIN
prior to programming the lock. The Master code will also operate (unlock/lock) the lock.
Network Module Setting: With the optional Network Module installed, this setting becomes available thru the
Main Menu (7) and allows the lock to connect with a network controller.
One Touch Locking: When the latch is retracted, activating the keypad will extend the latch (during Automatic Re-
lock duration or when Automatic Re-lock is disabled). When One-Touch Re-lock is in use any validnot (disabled),
PIN code will re-lock the lock.
Previous: While in Menu Mode, pressing this icon cancels the current operation and returns the user to the
previous step.
Privacy Mode: Privacy mode is disabled by default. Enable Privacy mode by pressing the privacy button for 4
seconds to put the lock in do-not-disturb mode (all pin codes are disabled).
Shutdown Time: The unit will shutdown (flashing ) for sixty (60) seconds and not allow operation after theRED
wrong code entry limit (5 attempts) has been met.
Tamper Alert: Audible alarm sounds if attempting to forcibly remove outside lock from door.
User Code:PIN The User code operates the lock. Maximum number of user codes is 250 with Network Module;
without Network Module, maximum is 25 user codes. Note: When deleting User code(s), screen will displayPIN
User Number (not code) being deleted.PIN
Volume Setting Mode: Low (2)The volume setting for code verification is set to by default; otherwise it canPIN
be set to or for quiet areas.High (1) Silent (3)
Wrong Code Entry Limit: After five (5) unsuccessful attempts at entering a valid code, the unit will shutPIN
down and not allow operation.
Definitions

17
P/N -220- - Rev FAYRD INST FUL
*The Master code must be registered prior to any other programming of the lock.PIN
Privacy Button Setting
Handing the Lock Performs automatic
handing of the lock
Continue
Complete
Continue
Complete
Master Code SettingPIN M
User Code RegistrationPIN
Register
Delete
Advanced Lock Settings
Volume Setting
Language Setting mode
Lockout Mode
**Network Module Setting Join the network
Enable
Disable
Exit the network
User Number ( )UN
1~25: without network module
U
**This function only appears when a
Network Module installed.
*Automatic Re-lock Enable
Disable
Inside Indicator Light
One Touch Locking Enable
Disable
Enable
Disable
Default settings
in bold.
English
Spanish
French
3
M
12
Silent
Low
High
Continue
Complete
1~250: with network module
Enable
Disable
1. Touch screen with back of hand or palm to activate.
2. Enter 4-8 digit master code* followed by key.PIN
Lock Response: "Menu mode, enter number, press key to continue."
3. Enter digit corresponding to the function to be performed followed by the key.
Follow the voice commands.
Feature Programming Through Menu Mode
Using Master code*PIN
*This feature is available with certain
Z-Wave and ZigBee controllers when
a Network Module is used.

18
P/N -220- - Rev FAYRD INST FUL
PIN codes must consist of 4 to 8 digits to register.
Disable Auto Re-lock Mode to lock the door (automatically).
The digits entered were incorrect or incomplete. Re-enter
the correct code followed by the star key.
This is the alert to replace the batteries. Replace all four
(4) batteries* with new Alkaline batteries.AA
Check to see if Silent Mode is enabled (see Feature #4).
Setting/managing Lockout Mode is done through
Master Code only. Contact the Master user.
Check to see if the lock is set to Lockout Mode.
Contact the Master user.
Only the Master can enable/disable Lockout Mode.
Lockout Mode is enabled.
Star or pound cannot be used as part of the code.PIN
Contact the Master user.
Check that the wire harness is firmly connected to the .PCB
Check the door gaps for any foreign objects between door
and frame.
Batteries may be completely discharged.
Check batteries are installed and oriented correctly (polarity)
in the battery case.
User codes must be entered within 5 seconds (while
touchscreen is active) or process will have to be restarted.
Registration/management of codes is set by thePIN
authority of the Master Code, which is set first.
The same code cannot be used for multiple users.PIN
If low battery indicator is lit (see below), change batteries*.
Check to see if Auto Re-lock Mode is enabled.
Batteries do not have enough power. Replace batteries*.
Use mechanical key to gain entry and replace batteries*.
Check to see if touchscreen harness is fully connected
and not pinched.
Check batteries are in good condition; replace batteries*
if discharged.
If touchscreen numbers are visible, check to see if they
respond when pressed.
Touchscreen becomes active when pressed w/whole hand.
Use a larger area of the hand or fingers and verify contact
with at least 3 areas.
Symptom Suggested Action
Lock does not respond –
door is open and
accessible.
Unit chimes to indicate
code acceptance, but the
door will not open.
Unit operates to allow
access, but will not
automatically re-lock.
PIN codes will not register.
Upon entering a codePIN
and pressing key, the
unit displays " invalid code"
error or lock times out with-
out responding.
Upon entering a codePIN
and pressing the key,
the red padlock icon appears
and there are different tones.
The unit operates, but it
makes no sound.
The unit responds
" Low Battery"
Upon entering a codePIN
and pressing the key,
the unit responds " Wrong
number of digits" .
Lock does not respond –
door is locked and
inaccessible.
Unit is on for a while then
shows no reaction. Lights
dim.
* When batteries are replaced, Network Module locks have a real time clock that will be set through the User Interface ( );UI
it is recommended to verify correct date and time particularly those locks operating under Daylight Saving Time ( ).DST
** Network Module locks only
Programming Troubleshooting

19
P/N -220- - Rev FAYRD INST FUL
L
w
T
Changing Lock: Replacing Cylinder
Hardware Troubleshooting
Cycle lock in both the locked and unlocked positions. If problems are found:
1-3/8" * - 2" thick doors:
= 3-1/2" (88.8mm)L
2" - 2-1/4" thick doors:
= 3-3/4" (95.3mm)L
W= .2" (5.2mm)
Tailpiece
T= .098" (2.5mm)
1.To Remove cylinder:
A. Remove outside escutcheon from door.
B. Remove rubber gasket.
C. Insert small flathead screwdriver under spring. Gently lift spring.
Note: Notch on top of cylinder engages spring.
D. Remove cylinder by pulling outward towards outside of door.
Before installing cylinder, be sure tailpiece is correct length
(see below).
2.To install new cylinder:
A. Reverse previous steps for removing cylinder.
*Requires addition of Thin Door Kit.
Bolt will not deadlock
a. Check for sufficient clearance of the bolt within the strike-side jamb. Correct this by
increasing the depth of the pocket for the bolt.
b. Check for misalignment of bolt and/or strike which may be preventing bolt from
properly entering the strike. With the door open, extend and retract the bolt; if it is
smooth, check the strike alignment.
Bolt does not extend or retract smoothly
a. Bolt and strike are misaligned, see above.
b. Check the backset of door relative to adjustments already made to bolt.
c. Verify proper door preparation and re-bore holes that are too small or misaligned.
d. Verify keypad wire harness is routed under the bolt (see Fig. A).
e. Verify bolt is installed with correct side up (Fig. A).
Keypad numerics are scrolling
Remove interior escutcheon and check to ensure that the wire harness lies flat against
the back recessed area and is properly routed along the side of the escutcheon and
tucked under the plastic cable guide.
Figure A

20
P/N -220- - Rev FAYRD INST FUL
FCC:
Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ technician for help.TV
Industry Canada:
This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.
Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant des règlements
d'équipement.
Warning: Yale Security Inc.Changes or modifications to this device, not expressly approved by could void the user's authority
to operate the equipment.
Yale® and Yale Real Living® are registered trademarks of Yale Security Inc., an Group company.ASSA ABLOY
Copyright © 2017, Yale Security Inc., an Group company.ASSA ABLOY
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY is the global leader in door opening solutions,
dedicated to satisfying end-user needs for security, safety and convenience.
Product Support Tel [phone] • www.yalehome.com
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.
YALE, with its unique global reach and range of products, is the world's favorite lock
– the preferred solution for securing your home, family and personal belongings.