Yardistry MERIDIAN OCTAGON YM11924 User manual

MERIDIAN OCTAGON GAZEBO
Installaon and Operang Instrucons – YM11924
Revised 04-26-2021
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
Yardistry – North America
Toll Free Customer Support:
1.888.509.4382
[e-mail]
www.yardistrystructures.com
Y40000-924
YM11924 - Meridian Octagon
12' 0"
3.658 m
12' 0"
3.658 m
12’
(3.658 m)
12’
(3.658 m)
Height: 9’ 11-5/16” (3.03 m)

2 [email protected]
Important Safety Notice!
Yardistry components are intended for privacy, decorative and ornamental use only.
Product is NOT INTENDED for the following:
• A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds.
• As load bearing support for a building, structure, heavy objects or swings.
• Used in structures that trap wind, rain or snow that would create extra load on the
product.
Accumulated snow must be removed from roof.
DO NOT climb or walk on roof for any reason.
Permanent structures may require a building permit. As the purchaser and or installer of this
product you are advised to consult local planning, zoning and building inspection departments for
guidance on applicable building codes and/or zoning requirements.
Wood is NOT ame retardant and will burn. Grills, re pits and chimineas are a re hazard if
placed too close to a Yardistry structure. Consult user’s manual of the grill, re pit or chimnea for
safe distances from combustible materials.
Wear gloves to avoid injury from possible sharp edges of individual elements before assembly.
During installation, follow all safety warnings provided with your tools and use OHSA
approved safety glasses. Some structures may require two or more people to install safely.
Check for underground utilities before digging or driving stakes into the ground!
It is important during assembly to closely follow the instructions, complete the assembly
on a solid level surface and that you follow the instruction to square up, level and anchor the
structure, this will reduce the gap at wood connections during assembly.
General Information: Wood components are manufactured with Cedar (C. Lanceolata)
which is protected with factory applied water-based stain. Knots, small checks (cracks)
and weathering are naturally occurring and do not a󰀨ect the strength of the product.
Annual application of a water-based water repellent sealant or stain is important and will
help reduce weathering and checks.
www.yardistrystructures.com
Questions?
Call toll free or write us at:
1 [phone]
[email protected]
Patents Pending
General Information

3 [email protected]
July 27, 2018
Limited Warranty
This Warranty gives you specic legal rights. You may have other rights as well which vary from state to state
or province to province. This warranty excludes all consequential damages, however, some states/provinces
do not allow the limitation or exclusion of consequential damages, and therefore this limitation may not apply
to you.
Yardistry warrants that this product is free from defect in materials and workmanship for a
period of one (1) year from the original date of purchase. In addition, for any product with
lumber, all lumber is warranted for ve (5) years against rot and decay. This warranty applies
to the original owner and registrant and is non-transferable.
Regular maintenance is required to assure the integrity of your product and is a requirement of
the warranty. This warranty does not cover any inspection costs.
This Limited Warranty does not cover:
• Labour for replacement of any defective item(s);
• Incidental or consequential damages;
• Cosmetic defects which do not a󰀨ect performance or integrity;
• Vandalism; improper use or installation; acts of nature, including but not limited to wind,
storms, hail, oods, excessive water exposure;
• Minor twisting, warping, checking or any other natural occurring properties of wood that do
not a󰀨ect performance or integrity.
Yardistry products have been designed for safety and quality. Any modications made to
the original product could damage the structural integrity of the product leading to failure
and possible injury. Yardistry cannot assume any responsibility for modied products.
Furthermore, modication voids any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Yardistry disclaims all other
representations and warranties of any kind, express or implied.

4 [email protected]4 [email protected]
Instructions for Proper Maintenance
Your Yardistry structure is designed and constructed of quality materials. As with all outdoor
products it will weather and wear. To maximize the enjoyment, safety and life of your structure
it is important that you, the owner, properly maintain it.
Symbols:
Throughout these instructions symbols are provided in the top, right-hand corner of the page.
If you dispose of your Yardistry structure: Please disassemble and dispose of your unit
so that it does not create any unreasonable hazards at the time it is discarded. Be sure to
follow your local waste ordinances.
HARDWARE:
• Check metal parts for rust. If found, sand and repaint using a non-lead paint complying
with 16 CFR 1303.
• Inspect and tighten all hardware after completion of assembly; after rst month of use; and
then annually. Do not over-tighten as to cause crushing and splintering of wood.
• Check for sharp edges or protruding screw threads, add washers if required.
WOOD PARTS:
• Applying a water repellent or stain (water-based) on a yearly basis is important
maintenance to maintain maximum life and performance of the product.
• Check all wood members for deterioration, structural damage and splintering. Sand down
splinters and replace deteriorated wood members. As with all wood, some checking and
small cracks in grain is normal
• Some gapping may occur at some wood connections.
• Tape Measure
• Carpenters Level
• Standard or Cordless Drill
• 7/16”, 1/2” Wrench
• 7/16”, 1/2” Socket
Assembly Guides
• 8’ Step Ladder
• Safety Glasses
• Adult Helper
• Safety Gloves
• Hard Hat
Tools Required:
• Use Help, where this is shown, 2, 3 or 4
people are required to safely complete
this step. To avoid injury or damage to the
assembly make sure to get some help.
• Use a measuring tape to assure proper
location
• Pre-drill a pilot hole before fastening
screw or lag to prevent splitting of wood.
• 6’ Step Ladder x 2
• Square
• Ratchet
• Check that assembly is square before
tightening bolts

5 [email protected]
Following are some helpful tips to make the assembly process smooth and e󰀩cient.
PRE-ASSEMBLIES:
(i.e. Post and Beam Assemblies, Roof Rafter Assembly, etc)
• Work on a raised, solid and at surface such as, a table or saw horse.
• Keep all connections ush where shown in the instructions.
• When assembling the beams keep parts at, straight and snug when
connecting.
METAL PARTS:
• Roong material may have sharp edges, wear safety gloves.
• Remove all plastic covering, on both sides of the metal panels, directly
before installing each piece.
• Place roong material on a non-abrasive surface before and after assembly
as it can bend, dent and scratch easily.
• The roong screws can easily crush the roof panels and roof edges when
using a power drill. We recommend hand tightening the roong screws so
they sit snug and tight to the roong material.
Assembly Tips

6 [email protected]
"B"
"B"
"C" "B"
"C"
"C" "B"
YM11924 - Meridian Octagon
Marker Metric Dimension Imperial Dimension
"A" 3.429 m 11'- 3"
"B" 1.420 m 4'- 7-15/16"
"C" 1.004 m 3'- 3-9/16'
"D" 3.712 m 12'- 2-1/8"
"A"
"A"
"C"
135"
3.43
Post to Post
135"
3.43
Post to Post
139.63
3.55
Post to Post
Note: It is critically important you start with square, solid and level footings, concrete
pad or deck to attach your Pavilion.
We supply Post Mounts with this structure which gives you the exibility to permanently install your structure
to a pre-existing or new wood or concrete surface.
• The hardware to attach the Post Mount to the structure is included.
• The hardware to mount the structure permanently will need to be purchased separately at your local
hardware store.
If you are mounting to concrete footers see below for the correct locations and placement. Please double
check for possibility of any underground utilities such as gas, telephone, cable or sprinkler lines.
Following are some examples of how to mount the structure to wood or concrete surfaces.
Refer to your local building and city codes, ordinances, neighbourhood covenants, or height restrictions
regarding this type of structure for guidance on acceptable installation requirements.
Permanent Installation Examples
Concrete Footer
To
Required
Depth
Anchoring Hardware not included
Post Mount
Outside Post to
Outside Post
A
AD
B
C
C
CC
B
B
Layout Dimensions for Octagon Gazebo
A11' 3" (3.429 m)
B4' 7-15/16" (1.421 m)
C3' 3-9/16" (1.005 m)
D 12' 2-5/16" (3.716 m)
Layout Dimensions for Octagon Gazebo
Actual for Gazebo Octagon Shape
(conrete or wood)
Concrete Footing
(centre of post)
A11' 3" (3.429 m) 12' 3" (3.734 m) 10' 10-1/8" (3.305 m)
B4' 7-15/16" (1.421 m) 5' 7/8" (1.546 m) 4' 5-7/8" (1.346 m)
C3' 3-9/16" (1.005 m) 3' 7-1/16" (1.092 m) 3' 2-1/8" (0.968 m)

7 [email protected]
STEP 12- Anchoring
A: After the all the walls have been installed, check that the unit is square, then anchor.
WOOD APPLICATION
CONCRETE APPLICATION
WOOD APPLICATION
CONCRETE APPLICATION
WOOD APPLICATION
CONCRETE APPLICATION
WOOD APPLICATION
CONCRETE APPLICATION
Permanent Installation Examples cont.
Anchoring Hardware not included
Anchoring Hardware not included
Anchoring Hardware (not included)
Post
Mount
Post Mounts have a 1/2” diameter
hole for anchoring hardware.
Concrete Patio [min. 12’ 3” x 12’ 3” (3.734 m x 3.734 m)]
with 6” (15.24 cm) clearance on all sides
Wood Deck [min. 12’ 3” x 12’ 3” (3.734 m x 3.734 m)]
with 6” (15.24 cm) clearance on all sides

8 [email protected]
Part Identification ( )
Dimensions are approximate and are shown to assist in the identification of parts for
assembly. Actual dimensions may be smaller or larger.
Y50131-10657pc. (1065) - Filler Insert 1307.1mm (51-1/2")
Y50131-1073
8pc. (1073) - Short Left Gusset 533.4mm (21")
Y70131-1056
6pc. (1056) - Post Main 2184.4mm (86")
Y70131-10591pc. (1059) - Post Left 2184.4mm (86")
Y70131-10611pc. (1061) - Post Right 2184.4mm (86")
8pc. (1062) - Beam 1451.9mm (57-1/8") Y50131-1062
Y50131-1064
7pc. (1064) - Top Rail 1307.1mm (51-1/2")
84pc. (1066) - Spindle 747.8mm (29-7/16") Y50131-1066
Y50131-1074
8pc. (1074) - Short Right Gusset 533.4mm (21")
Y50131-10637pc. (1063) - Bot Rail 1307.1mm (51-1/2")

9 [email protected]
Part Identification ( )
Dimensions are approximate and are shown to assist in the identification of parts for
assembly. Actual dimensions may be smaller or larger.
Y50131-1068
8pc. (1068) - RT Corner Rafter 2032mm (80")
Y50131-10718pc. (1071) - Rafter Centre 1902mm (74-7/8")
Y50131-1067
8pc. (1067) - LT Corner Rafter 2032mm (80")
Y50131-10708pc. (1070) - Bot Strap 1076.6mm (42-3/8")
Y50131-1069
8pc. (1069) - Top Strap 633.9mm (25")
8pc. (1072) - Fascia 1494mm (58-13/16") Y50131-1072

10 [email protected]
Dimensions are approximate and are shown to assist in the identification of
parts for assembly. Actual dimensions may be smaller or larger.
Hardware Identification ( )
1pc. - Octagon Roof Peak Set
(Y70829-390)
1pc.
Peak Post
(Y01000-094)
1pc. - Gazebo ID Plaque
(Y70800-104)
8pc.
(Y01033-357)
- LT Panel 1pc. -Octagon
Gazebo Roofing Set
(Y70833-356)
1pc.
1/4" Nut
(Y08490-200)
1pc.
Carriage Bolt
(Y07490-260)
1pc.
Spring Clip
(Y09490-001)
1pc.
Peak Loop
(Y20018-003)
1pc. - Rafter/Beam
Bracket Set (8Pk)
(Y70829-281)
8pc. Ridge Cap 79 - (Y00433-361)
8pc. Roof Edge - (Y01033-359)
16pc. Ridge Clip 78 - (Y00433-358)
1pc. - 135º Angle
Bracket Set (8Pk)
(Y70818-389)
8pc. - RT Panel
(Y01033-356)
1pc. - Corner Cap Set (8Pk)
(Y70833-354)
1pc. - Post
Mount Set (8Pk)
(Y70829-355)
1pc.
Peak Cap
(Y01033-351)
1pc. - Roof Clip
Weather Seal (16Pk)
(Y70818-360)
1pc. - Post Roof Tie
Bracket Set (8Pk)
(Y70829-353)
Washer
Contour
(Y05918-211)
1pc.
1pc.
Base Plate
(Y01029-352)

11 [email protected]
Hardware Identification ( )
Dimensions are approximate and are shown to assist in the identification of
parts for assembly. Actual dimensions may be smaller or larger.
16pc. Hex Bolt
1/4 x 5"
(Y07718-250)
128pc. Wood Screw #8 x 3" - (Y06091-530)
8pc. 1/4 x 2" Hex Bolt - (Y07718-220)
32pc. Pan Screw #12 x 1-1/2"
(Y06491-612)
1pc. #2 x 2" Robertson Driver (Y00400-005)
32pc. 5/16" Lock Washer
(Y05318-300)
32pc. 5/16 - T-Nut
(Y08518-300)
84pc. Wood Screw #8 x 2" - (Y06091-520)
1pc. -1/8"Drill Bit
(Y00400-002)
224pc. Hex Roofing Screw
#8x 1"
(Y06733-510)
48pc. - 1/4" Lock Nut
(Y08318-203)
58pc. Pan Screw #10 x 1-1/4"
(Y06491-711)
48pc. Sheet Metal Screw
#8 x 3/4"
(Y06433-503)
1pc. - Hex Driver (Y00400-004)
149pc. Wood Screw #8 x 1-1/2"
(Y06091-512)
70pc. Wood Screw #8 x 2 1/2" - (Y06091-522)
32pc. Hex Bolt 5/16 x 2-1/4" - (Y07718-321)
24pc. 1/4 x 2-3/4 Hex Bolt - (Y07718-223)
144pc.
1/4-5/16 x 1-1/4" Large Washer
(Y05118-311)
80pc. Wood Screw #7 x 3/4"
(Y06091-003)
32pc. Lag Screw 1/4" x 1-15/16" No.12 Shank - (Y06218-219)

12 [email protected]
PRODUCT NUMBER: YM11924
CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 1)
CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 2)
CARTON I.D. STAMP: __ __ __ __ __ ___ (Box 3)
STOP STOPSTOP STOP
1-888-509-4382
[email protected]
C. Read the assembly manual completely, paying special attention to ANSI
warnings; notes; and safety/maintenance information on pages 1 - 4.
• Follow the instructions in order.
• This structure is designed to be assembled and installed ideally by four
people, DO NOT attempt to install alone.
• Consider the slope of elevation where you plan to install the structure. Also, check
for gas, telephone, other utilities or sprinkler line locations prior to excavating any
holes.
D. Before you discard your cartons ll out the form below.
• The carton I.D. stamp is located on the end of each carton.
• Please retain this information for future reference. You will need this information if
you contact the Consumer Relations Department.
• Each step indicates which bolts and/or screws you will need for assembly, as well
as any at washers, lock washers, t-nuts or lock nuts.
A. This is the time for you to inventory all your hardware, wood and accessories,
referencing the parts identication sheets. This will assist you with your
assembly.
Step 1: Inventory Parts - Read This Before Starting Assembly
B. If there are any missing or damaged pieces or you need assistance with
assembly please contact the consumer relations department directly. Call us
before going back to the store.

13 [email protected]
STEP 1 - RAILS
Follow steps below, then complete another 6 more assemblies.
A: Place 12 spindles (1066) in the filler (1065) slots to get spacing. Attach Bot Rail (1063) using #8 x
3” Wood Screws.
B: Remove filler (1065) and attach to the other end of the Spindles, using #8 x 2” Wood Screws.
STEP 1 - RAILS
Follow steps below, then complete another 6 more assemblies.
A: Place 12 spindles (1066) in the filler (1065) slots to get spacing. Attach Bot Rail (1063) using #8 x
3” Wood Screws.
B: Remove filler (1065) and attach to the other end of the Spindles, using #8 x 2” Wood Screws.
A: Place 12 (1066) Spindles into the slots of (1065) Filler. This will provide proper spacing. Place (1063) Bot Rail
against bottom of spindles, ush to the outside edges of the end spindles. Centre spindles over holes in (1063) Bot
Rail. Attach with one #8 x 3” Wood Screw per spindle. (F2.1 and F2.2)
B: Remove (1065) Filler from bottom of (1066) Spindles and place at top of spindles, ush to outside edges of end
spindles and attach with one #8 x 2” Wood Screw per spindle. (F2.2)
Step 2: Rail Assemblies
Part 1
HardwareWood Parts
F2.2
(1066) Spindle
(x 12)
7 x (1063) Bot Rail
7 x (1065) Filler
84 x (1066) Spindle
#8 x 2” Wood
Screws (x 12)
#8 x 3” Wood
Screws (x 12)
84 x #8 x 2” Wood Screw
84 x #8 x 3” Wood Screw
F2.1
Flush
(1065)
Filler
(1063) Bot Rail
(1065)
Filler
(1063) Bot Rail
(1066)
Spindle
Note: Angle side
towards spindles

14 [email protected]
STEP 1 - RAILS
Follow steps below, then complete another 7 more assemblies.
C: Place Top Rail (1064) on filler (1065) flush to one end then attach
together using #8 x 1-1/2” Wood Screws from the filler side.
STEP 1 - RAILS
Follow steps below, then complete another 7 more assemblies.
C: Place Top Rail (1064) on filler (1065) flush to one end then attach
together using #8 x 1-1/2” Wood Screws from the filler side.
C: On top of (1065) Filler and ush to each end, place (1064) Top Rail. Attach (1065) Filler to (1064) Top Rail with
three #8 x 1-1/2” Wood Screws as shown in F2.3 and F2.4.
D: Repeat Steps A - C six more times to create seven Rail Assemblies.
Step 2: Rail Assemblies
Part 2
HardwareWood Parts
7 x (1064) Top Rail 21 x #8 x 1-1/2” Wood Screw
#8 x 1-1/2” Wood
Screws (x 3 per
assembly)
F2.3
F2.4
(1065)
Filler
(1064) Top Rail
(1065)
Filler
(1064)
Top Rail
Flush
Flush

15 [email protected]
STEP 3 - POST Assembly
STEP 3 - POST Assembly
STEP 3 - POST Assembly
STEP 3 - POST Assembly
STEP 3 - POST Assembly
STEP 3 - POST Assembly
A: Flush to the bottom of one (1059) Post Left and one (1061) Post Right place one Post Mount tight to the inside
of each post then attach with two #10 x 1-1/4” Pan Screws per Post Mount. (F3.1, F3.2, F3.3 and F3.4)
B: Flush to the bottom of each (1056) Post Main place one Post Mount tight to the inside of each post then attach
with two #10 x 1-1/4” Pan Screws per Post Mount. There will be six Post Main Assemblies. (F3.5 and F3.6)
Step 3: Post Assemblies
HardwareWood Parts
F3.3
6 x (1056) Post Main
1 x (1059) Post Left
1 x (1061) Post Right
Top
Bottom
F3.5
8 x Post Mount
F3.1
Post
Mount
F3.2
Post
Mount
#10 x 1-1/4”
Pan Screw
Flush
(1061)
Post Right
16 x #10 x 1-1/4” Pan Screw
Components
F3.4
F3.6
Bottom
(1059)
Post Left (1056)
Post Main
(1061)
Post Right
(1059)
Post Left
(1056)
Post Main
Flush
Flush
#10 x 1-1/4”
Pan Screw
Note: Holes
at top of posts

16 [email protected]
STEP 4 - POST/RAIL Assembly
LAYOUT FOR 1 RIGHT POST ASSEMBLY
LAYOUT FOR 2 MAIN POST ASSEMBLIES
LAYOUT FOR 1 Left POST ASSEMBLY
A: Place two Post Main (1056) on each side of one Rail Assembly and attach using (2)
#8 x 2-1/2” Wood Screws. (First Image) -Repeat for 2nd assembly.
B: Place One Post Main 1056) on the right side of the Rail Assembly and one Post Right
(1061) on the left side and attach using (2) #8 x 2-1/2” Wood Screws. (Second Image) C: Place
One Post Main 1056) on the left side of the Rail Assembly and one Post Left(1059) on the right side
and attach using (2) #8 x 2-1/2” Wood Screws. (Third Image)
STEP 4 - POST/RAIL Assembly
#8
x
3"
Scr
ew
DA: Continue attaching each Rail Assembly to the Posts, using a a 3/16" drill bit to pre-drill
a hole through each Spindle touching the post.a
Attach using (2) #8 x 3” Wood Screws. Note: Pre-drill at an angle.
STEP 4 - POST/RAIL Assembly
#8
x
3"
Scr
ew
DA: Continue attaching each Rail Assembly to the Posts, using a a 3/16" drill bit to pre-drill
a hole through each Spindle touching the post.a
Attach using (2) #8 x 3” Wood Screws. Note: Pre-drill at an angle.
STEP 4 - POST/RAIL Assembly
#8
x
3"
Scr
ew
DA: Continue attaching each Rail Assembly to the Posts, using a a 3/16" drill bit to pre-drill
a hole through each Spindle touching the post.a
Attach using (2) #8 x 3” Wood Screws. Note: Pre-drill at an angle.
STEP 4 - POST/RAIL Assembly
LAYOUT FOR 1 RIGHT POST ASSEMBLY
LAYOUT FOR 2 MAIN POST ASSEMBLIES
LAYOUT FOR 1 Left POST ASSEMBLY
A: Place two Post Main (1056) on each side of one Rail Assembly and attach using (2)
#8 x 2-1/2” Wood Screws. (First Image) -Repeat for 2nd assembly.
B: Place One Post Main 1056) on the right side of the Rail Assembly and one Post Right
(1061) on the left side and attach using (2) #8 x 2-1/2” Wood Screws. (Second Image) C: Place
One Post Main 1056) on the left side of the Rail Assembly and one Post Left(1059) on the right side
and attach using (2) #8 x 2-1/2” Wood Screws. (Third Image)
Step 4: Attach Rail Assemblies to Posts
Part 1
Hardware
A: Place one (1056) Post Main on each side of one Rail Assembly. Rail Assembly should sit tight to top of post
insert. See F4.1 and F4.2 for correct positioning of posts. At an angle attach (1064) Top Rail to posts with two #8 x
2-1/2” Wood Screws. (F4.1, F4.2, F4.3 and F4.4)
B: For each (1066) Spindle which is next to a post, at an angle, pre-drill with a 1/8” drill bit then attach (1066)
Spindles to posts, on an angle, with two #8 x 3” Wood Screws per post. (F4.5 and F4.6)
C: Repeat Steps A and B for a second Rail Assembly using two (1056) Post Mains.
F4.1
4 x #8 x 2-1/2” Wood Screw
8 x #8 x 3” Wood Screw
Post
Insert
Rail
Assembly
Tight
(1066) Spindle
#8 x 2-1/2”
Wood Screw
F4.2
Pre-drill and
attach screws at
an angle
Notice screw
attached at an
angle
(1056)
Post Main
F4.3
(1056)
Post Main
(1064)
Top Rail (1056)
Post Main
F4.4
F4.5
#8 x 3”
Wood
Screw
(1056)
Post Main
(1056)
Post Main
(1066) Spindle
Notice Posts
face the same
direction
STEP 5 - Wall Assembly -(x2)
Follow steps below, then complete another assembly
A: Place Beam (1062) onto one Rail/Post frame from previous step. ˜ush t o each end then
attach togeth-er using #8 x 3” Wood Screws and 1/4 x 5“ Hex Bolt (1/4” Large Washer, Lock Nut,
135º Bracket)
B: Attach Short Gusset Left (1073) and Right (1072) using 51/46” x 2 1/4” Hex BLT (1/4 LG Washer,
5/16 T-Nut, Lock Washer), then tighten corner using 1/4 x 1-15/16” Lag Screws (1/4” Lg Washers)
C: Repeat steps from above for one more assembly
F4.6

17 [email protected]
STEP 4 - POST/RAIL Assembly
#8
x
3"
Scr
ew
DA: Continue attaching each Rail Assembly to the Posts, using a a 3/16" drill bit to pre-drill
a hole through each Spindle touching the post.a
Attach using (2) #8 x 3” Wood Screws. Note: Pre-drill at an angle.
(1066) Spindle
STEP 4 - POST/RAIL Assembly
#8
x
3"
Scr
ew
DA: Continue attaching each Rail Assembly to the Posts, using a a 3/16" drill bit to pre-drill
a hole through each Spindle touching the post.a
Attach using (2) #8 x 3” Wood Screws. Note: Pre-drill at an angle.
STEP 5 - Wall Assembly -(x2)
Follow steps below, then complete another assembly
A: Place Beam (1062) onto one Rail/Post frame from previous step. ˜ush t o each end then
attach togeth-er using #8 x 3” Wood Screws and 1/4 x 5“ Hex Bolt (1/4” Large Washer, Lock Nut,
135º Bracket)
B: Attach Short Gusset Left (1073) and Right (1072) using 51/46” x 2 1/4” Hex BLT (1/4 LG Washer,
5/16 T-Nut, Lock Washer), then tighten corner using 1/4 x 1-15/16” Lag Screws (1/4” Lg Washers)
C: Repeat steps from above for one more assembly
STEP 4 - POST/RAIL Assembly
LAYOUT FOR 1 RIGHT POST ASSEMBLY
LAYOUT FOR 2 MAIN POST ASSEMBLIES
LAYOUT FOR 1 Left POST ASSEMBLY
A: Place two Post Main (1056) on each side of one Rail Assembly and attach using (2)
#8 x 2-1/2” Wood Screws. (First Image) -Repeat for 2nd assembly.
B: Place One Post Main 1056) on the right side of the Rail Assembly and one Post Right
(1061) on the left side and attach using (2) #8 x 2-1/2” Wood Screws. (Second Image) C: Place
One Post Main 1056) on the left side of the Rail Assembly and one Post Left(1059) on the right side
and attach using (2) #8 x 2-1/2” Wood Screws. (Third Image)
STEP 4 - POST/RAIL Assembly
LAYOUT FOR 1 RIGHT POST ASSEMBLY
LAYOUT FOR 2 MAIN POST ASSEMBLIES
LAYOUT FOR 1 Left POST ASSEMBLY
A: Place two Post Main (1056) on each side of one Rail Assembly and attach using (2)
#8 x 2-1/2” Wood Screws. (First Image) -Repeat for 2nd assembly.
B: Place One Post Main 1056) on the right side of the Rail Assembly and one Post Right
(1061) on the left side and attach using (2) #8 x 2-1/2” Wood Screws. (Second Image) C: Place
One Post Main 1056) on the left side of the Rail Assembly and one Post Left(1059) on the right side
and attach using (2) #8 x 2-1/2” Wood Screws. (Third Image)
D: Place one (1056) Post Main on one side of one Rail Assembly and (1059) Post Left on the other side. Rail
Assembly should sit tight to top of post insert. See F4.7 and F4.8 for correct positioning of posts. At an angle,
attach (1064) Top Rail to posts with two #8 x 2-1/2” Wood Screws. (F4.7, F4.8, F4.9 and F4.10)
E: For each (1066) Spindle which is next to a post, at an angle, pre-drill with a 1/8” drill bit then attach (1066)
Spindles to posts, on an angle, with two #8 x 3” Wood Screws per post. (F4.11 and F4.12)
Step 4: Attach Rail Assemblies to Posts
Part 2
STEP 4 - POST/RAIL Assembly
#8
x
3"
Scr
ew
DA: Continue attaching each Rail Assembly to the Posts, using a a 3/16" drill bit to pre-drill
a hole through each Spindle touching the post.a
Attach using (2) #8 x 3” Wood Screws. Note: Pre-drill at an angle.
F4.7
Rail
Assembly
#8 x 2-1/2”
Wood Screw
F4.8
Notice screw
attached at an
angle
(1059)
Post Left
(at side)
F4.9
(1056)
Post Main
(1064)
Top Rail Post
F4.11
F4.10
Hardware
2 x #8 x 2-1/2” Wood Screw
4 x #8 x 3” Wood Screw
(1059)
Post Left
Notice groove
side faces Rail
Assembly, at
side faces away
Notice Post Main
faces the same
direction as Post Left
Post
(1059)
Post Left
F4.12
Tight
Pre-drill and
attach screws at
an angle #8 x 3”
Wood
Screw
(1056)
Post Main
(1066) Spindle
Post
Post
Insert

18 [email protected]
STEP 4 - POST/RAIL Assembly
#8
x
3"
Scr
ew
DA: Continue attaching each Rail Assembly to the Posts, using a a 3/16" drill bit to pre-drill
a hole through each Spindle touching the post.a
Attach using (2) #8 x 3” Wood Screws. Note: Pre-drill at an angle.
STEP 4 - POST/RAIL Assembly
#8
x
3"
Scr
ew
DA: Continue attaching each Rail Assembly to the Posts, using a a 3/16" drill bit to pre-drill
a hole through each Spindle touching the post.a
Attach using (2) #8 x 3” Wood Screws. Note: Pre-drill at an angle.
STEP 5 - Wall Assembly -(x2)
Follow steps below, then complete another assembly
A: Place Beam (1062) onto one Rail/Post frame from previous step. ˜ush t o each end then
attach togeth-er using #8 x 3” Wood Screws and 1/4 x 5“ Hex Bolt (1/4” Large Washer, Lock Nut,
135º Bracket)
B: Attach Short Gusset Left (1073) and Right (1072) using 51/46” x 2 1/4” Hex BLT (1/4 LG Washer,
5/16 T-Nut, Lock Washer), then tighten corner using 1/4 x 1-15/16” Lag Screws (1/4” Lg Washers)
C: Repeat steps from above for one more assembly
Post
Tight
Pre-drill and
attach screws at
an angle #8 x 3”
Wood
Screw
(1056)
Post Main
(1066) Spindle
Post
STEP 4 - POST/RAIL Assembly
LAYOUT FOR 1 RIGHT POST ASSEMBLY
LAYOUT FOR 2 MAIN POST ASSEMBLIES
LAYOUT FOR 1 Left POST ASSEMBLY
A: Place two Post Main (1056) on each side of one Rail Assembly and attach using (2)
#8 x 2-1/2” Wood Screws. (First Image) -Repeat for 2nd assembly.
B: Place One Post Main 1056) on the right side of the Rail Assembly and one Post Right
(1061) on the left side and attach using (2) #8 x 2-1/2” Wood Screws. (Second Image) C: Place
One Post Main 1056) on the left side of the Rail Assembly and one Post Left(1059) on the right side
and attach using (2) #8 x 2-1/2” Wood Screws. (Third Image)
STEP 4 - POST/RAIL Assembly
LAYOUT FOR 1 RIGHT POST ASSEMBLY
LAYOUT FOR 2 MAIN POST ASSEMBLIES
LAYOUT FOR 1 Left POST ASSEMBLY
A: Place two Post Main (1056) on each side of one Rail Assembly and attach using (2)
#8 x 2-1/2” Wood Screws. (First Image) -Repeat for 2nd assembly.
B: Place One Post Main 1056) on the right side of the Rail Assembly and one Post Right
(1061) on the left side and attach using (2) #8 x 2-1/2” Wood Screws. (Second Image) C: Place
One Post Main 1056) on the left side of the Rail Assembly and one Post Left(1059) on the right side
and attach using (2) #8 x 2-1/2” Wood Screws. (Third Image)
Step 4: Attach Rail Assemblies to Posts
Part 3
F: Repeat Steps D and E using one (1056) Post Main with one (1061) Post Right. See F4.11 and F4.12 for correct
positioning of Posts.(F4.13, F4.14, F4.15, F4.16, F4.17 and F4.18)
STEP 4 - POST/RAIL Assembly
#8
x
3"
Scr
ew
DA: Continue attaching each Rail Assembly to the Posts, using a a 3/16" drill bit to pre-drill
a hole through each Spindle touching the post.a
Attach using (2) #8 x 3” Wood Screws. Note: Pre-drill at an angle.
F4.13
Rail
Assembly
(1066) Spindle
#8 x 2-1/2”
Wood Screw
F4.14
Notice screw
attached at an
angle
(1061)
Post Right
(at side)
F4.15
(1056)
Post Main
(1064)
Top Rail Post
F4.16
F4.18
Hardware
2 x #8 x 2-1/2” Wood Screw
4 x #8 x 3” Wood Screw
(1061)
Post Right Notice groove
side faces Rail
Assembly, at
side faces away
Notice Post Main
faces the same
direction as Post Left
(1061)
Post Right
F4.17
Post
Insert

19 [email protected]
STEP 5 - Wall Assembly -(x2)
Follow steps below, then complete another assembly
A: Place Beam (1062) onto one Rail/Post frame from previous step. ˜ush t o each end then
attach togeth-er using #8 x 3” Wood Screws and 1/4 x 5“ Hex Bolt (1/4” Large Washer, Lock Nut,
135º Bracket)
B: Attach Short Gusset Left (1073) and Right (1072) using 51/46” x 2 1/4” Hex BLT (1/4 LG Washer,
5/16 T-Nut, Lock Washer), then tighten corner using 1/4 x 1-15/16” Lag Screws (1/4” Lg Washers)
C: Repeat steps from above for one more assembly
STEP 5 - Wall Assembly -(x2)
Follow steps below, then complete another assembly
A: Place Beam (1062) onto one Rail/Post frame from previous step. ˜ush t o each end then
attach togeth-er using #8 x 3” Wood Screws and 1/4 x 5“ Hex Bolt (1/4” Large Washer, Lock Nut,
135º Bracket)
B: Attach Short Gusset Left (1073) and Right (1072) using 51/46” x 2 1/4” Hex BLT (1/4 LG Washer,
5/16 T-Nut, Lock Washer), then tighten corner using 1/4 x 1-15/16” Lag Screws (1/4” Lg Washers)
C: Repeat steps from above for one more assembly
STEP 5 - Wall Assembly -(x2)
Follow steps below, then complete another assembly
A: Place Beam (1062) onto one Rail/Post frame from previous step. ˜ush t o each end then
attach togeth-er using #8 x 3” Wood Screws and 1/4 x 5“ Hex Bolt (1/4” Large Washer, Lock Nut,
135º Bracket)
B: Attach Short Gusset Left (1073) and Right (1072) using 51/46” x 2 1/4” Hex BLT (1/4 LG Washer,
5/16 T-Nut, Lock Washer), then tighten corner using 1/4 x 1-15/16” Lag Screws (1/4” Lg Washers)
C: Repeat steps from above for one more assembly
Step 5: Main Wall Assembly
HardwareWood Parts
A: On one Rail/Post Main Assembly place one (1062) Beam against the wide side of the posts, ush to the edges
then loosely attach with two 1/4 x 5” Hex Bolts (with 1/4-5/16” large washer, 135° Bracket and 1/4” lock nut) in the
bottom holes. Make sure assembly is square then attach (1062) Beam to posts with two #8 x 3” Wood Screws in
the top holes. Tighten bolts. (F5.1 and F5.2)
B: Place one (1073) Short Left Gusset and one (1074) Short Right Gusset tight to the Posts and bottom of (1062)
Beam then attach to beam with two 5/16 x 2-1/4” Hex Bolts (with 5/16” lock washer, 1/4-5/16” large washer and
5/16” t-nut) per gusset. Pre-drill with a 1/8” drill bit then attach gusset to posts with two 1/4 x 1-15/16” Lag Screws
(with 1/4-5/16” large washer) per gusset. (F5.1 and F5.3)
C: Repeat Steps A and B for the second Rail/Post Main Assembly. This makes two Main Wall Assemblies.
F5.1
4 x 1/4 x 5” Hex Bolt (1/4-5/16” large washer, 135° Bracket, 1/4” lock nut)
8 x 5/16 x 2-1/4” Hex Bolt (5/16” lock washer, 1/4-5/16” large washer, 5/16” t-nut)
8 x 1/4 x 1-15-16” Lag Screw (1/4-5/16” large washer)
4 x #8 x 3” Wood Screw
1/4 - 5/16”
Large Washer
5/16 x 2-1/4”
Hex Bolt
(1073)
Short Left
Gusset
Post
2 x (1062) Beam
2 x (1073) Short Left Gusset
2 x (1074) Short Right Gusset
(1074) Short
Right Gusset
1/4”
Lock
Nut
#8 x 3”
Wood
Screw
(1062)
Beam
F5.2
Wide side
facing up
Flush
135°
Bracket
F5.3
Tight
5/16” T-nut
5/16”
Lock
Washer
1/4 x 5”
Hex Bolt
1/4 - 1-15/16”
Lag Screw
1/4 - 5/16”
Large Washer
Tight
1/4 - 5/16”
Large Washer
(1062)
Beam
Post
Gusset
(1062)
Beam
Post

20 [email protected]
STEP 6 - Right Wall Assembly -(x1)
Follow steps below, then complete another assembly
A: Place Beam (1062) onto Right Post/Rail Assembly from previous step. ˜ush t o each end then
attach together using #8 x 3” Wood Screws and 1/4 x 5“ Hex Bolt (1/4” Large Washer, Lock Nut, 135º
Bracket)
B: Attach Short Gusset Left (1073) and Right (1072) using 5/16” x 2¼” Hex BLT (1/4 LG Washer, 5/16 T-
Nut, Lock Washer), then tighten corner using 1/4 x 1-15/16” Lag Screws (1/4” Lg Washers)
STEP 6 - Right Wall Assembly -(x1)
Follow steps below, then complete another assembly
A: Place Beam (1062) onto Right Post/Rail Assembly from previous step. ˜ush t o each end then
attach together using #8 x 3” Wood Screws and 1/4 x 5“ Hex Bolt (1/4” Large Washer, Lock Nut, 135º
Bracket)
B: Attach Short Gusset Left (1073) and Right (1072) using 5/16” x 2¼” Hex BLT (1/4 LG Washer, 5/16 T-
Nut, Lock Washer), then tighten corner using 1/4 x 1-15/16” Lag Screws (1/4” Lg Washers)
STEP 6 - Right Wall Assembly -(x1)
Follow steps below, then complete another assembly
A: Place Beam (1062) onto Right Post/Rail Assembly from previous step. ˜ush t o each end then
attach together using #8 x 3” Wood Screws and 1/4 x 5“ Hex Bolt (1/4” Large Washer, Lock Nut, 135º
Bracket)
B: Attach Short Gusset Left (1073) and Right (1072) using 5/16” x 2¼” Hex BLT (1/4 LG Washer, 5/16 T-
Nut, Lock Washer), then tighten corner using 1/4 x 1-15/16” Lag Screws (1/4” Lg Washers)
Step 6: Left and Right Wall Assemblies
HardwareWood Parts
A: On one Rail/Post Left Assembly place one (1062) Beam against the wide side of the posts, ush to the edges
then loosely attach with two 1/4 x 5” Hex Bolts (with 1/4-5/16” large washer, 135° Bracket and 1/4” lock nut) in the
bottom holes. Make sure assembly is square then attach (1062) Beam to posts with two #8 x 3” Wood Screws in
the top holes. Tighten bolts. (F6.1 and F6.2)
B: Place one (1073) Short Left Gusset and one (1074) Short Right Gusset tight to the Posts and bottom of (1062)
Beam then attach to beam with two 5/16 x 2-1/4” Hex Bolts (with 5/16” lock washer, 1/4-5/16” large washer and
5/16” t-nut) per gusset. Pre-drill with a 1/8” drill bit then attach gusset to posts with two 1/4 x 1-15/16” Lag Screws
(with 1/4-5/16” large washer) per gusset. (F6.1 and F6.3)
C: Repeat Steps A and B for the Rail/Post Right Assembly.
F6.1
4 x 1/4 x 5” Hex Bolt (1/4-5/16” large washer, 135° Bracket, 1/4” lock nut)
8 x 5/16 x 2-1/4” Hex Bolt (5/16” lock washer, 1/4-5/16” large washer, 5/16” t-nut)
8 x 1/4 x 1-15-16” Lag Screw (1/4-5/16” large washer)
4 x #8 x 3” Wood Screw
2 x (1062) Beam
2 x (1073) Short Left Gusset
2 x (1074) Short Right Gusset
F6.2
(1073)
Short Left
Gusset
(1074) Short
Right Gusset
Wide side
facing up
Post (1062)
Beam
1/4”
Lock
Nut
#8 x 3”
Wood
Screw
Flush
135°
Bracket
1/4 x 5”
Hex Bolt
1/4 - 5/16”
Large Washer
(1062)
Beam
Post
1/4 - 5/16”
Large Washer
5/16 x 2-1/4”
Hex Bolt
Post
(1062)
Beam
Tight
5/16” T-nut
5/16”
Lock
Washer
1/4 - 1-15/16”
Lag Screw
1/4 - 5/16”
Large Washer
Tight
Gusset
F6.3