Zest 4 Leisure Hollywood Swing with Canopy User manual

Assembly Instructions
(W x D x H): 2.40m x 1.90m x 2.14m
Product Name: Hollywood Swing with Canopy
Pressure Treated products should not be treated with any other products for the first month.
PLEASE KEEP THIS INSTRUCTION
Zest4Leisure
01352 752555 option 1 –[e-mail]
V1-10.16

Hollywood Swing Assembly Instructions
Requires 2 person assembly.
Tools required: Corded / Cordless Drill, Pozi-drive Bit / Screwdriver, Socket Set,
Hammer, 3mm Drill Bit required in order for you to drill all screw holes before
construction.
Hollywood Swing Pack List
Item Description Quantity
ALeg 4
B Beam 1
C Horizontal Short Brace 2
D Horizontal Long Brace 2
E Diagonal Brace 2
F Seat Back 1
G Seat 1
H Armrest Support 2
J Armrest 2
K Shelf (Optional Extra) 2
L Beam Capping 1
Fixings
60mm Screws 8
45mm Bolts, washers & nuts 6
100mm Bolts, washers & nuts 22
115mm Eye Bolts & small karabiner, washers & nuts 4
150mm Bolts, washers & nuts 2
150mm Eye Bolts & large karabiner, washers & nuts 2
990mm Chain 2
1140mm Chain 2
www.zest4leisure.co.uk

Please take a few moments to check all pack contents listed.
Assembly requires 2 persons.
Tools required: Corded/Cordless Drill, Pozi-drive Bit/Screwdriver, Socket Set,
Hammer, 3mm Drill Bit required in order for you to drill all screw holes before
construction.
Hollywood Swing is now complete.
1. Position 2no Legs A either side of Beam B (See Fig.1a), align bolt holes and attach using 1no
150mm Bolt, washer & nut (See Fig.1b). Do not fully tighten at this stage. Repeat procedure for
the remaining 2no Legs A at the other end of Beam B.
2. Position Horizontal Short Brace C (See Fig. 2a) and Horizontal Long Brace D (See Fig. 2b)
onto Legs A, align bolt holes and insert 8no 100mm Bolts –4no per horizontal brace. Repeat
procedure for the remaining braces and Legs A.
3. Turn over the Legs/Beam Assembly (See Fig. 3a), attach washers and nuts and fully tighten
(See Fig. 3b).
4. Attach Diagonal Brace E to Beam B using 2no 100mm Bolts, washers & nuts and fully tighten
(See Fig. 4a). Raise Leg Assembly, align Diagonal Brace E & Horizontal Short Brace C bolt
holes and fix in position using 1no 100mm Bolt, washer & nut (See Fig. 4b). Fully tighten all
nuts at this stage. Repeat procedure with the remaining Diagonal Brace E at the other end of
Beam B (See Fig. 4c).
5. Insert 2no 150mm Eye Bolts into the Beam B (See Fig. 5) and secure using washers and nuts.
6. Locate half lap joints of Seat Back F into half lap joints of Seat G and fix in position using 6no
45mm Bolts, washers & nuts –2no per joint (See Fig. 6b)
7. Locate the Armrest Support H dowels into the Armrest J holes (See Fig. 7a) and fix in position
using 1no 60mm Screw (See Fig. 7b). Repeat procedure for the remaining Armrest Support H
and Armrest J.
8. Attach Armrest Assembly to Seat Assembly using 2no 115mm Eye Bolts as shown in Figs. 8a
& 8b. Repeat procedure for the remaining Arm Assembly.
9. Hook 1no Short Chain & 1no Long Chain onto Large Karabiner ensuring Short Chain is at the
back (See Fig. 9a). Repeat procedure for remaining chains. Attach Short Chain to the back of
the Seat Assembly (See Fig. 9b) and Long Chain to the front of the Seat Assembly (See Fig.
9c) using 2no Small Karabiners. Repeat procedure for remaining Chains.
10. Locate Shelves K (Optional Extra) onto Long Braces D (See Fig. 10).
11. Position Beam Capping L centrally along Beam B (See Fig. 11a) and fix in position using 6no
60mm Screws –1no into each Leg A (See Fig. 11b) and 2no into Beam B (See Fig. 11c)

www.zest4leisure.co.uk
1b1a
2a 2b
3a 3b
4a 4b

www.zest4leisure.co.uk
54c
6a 6b
7a 7b
8a 8b

www.zest4leisure.co.uk
9b9a
9c 10
11a 11b
11b

Hollywood Swing with Canopy Assembly
Instructions
Requires 2 person assembly.
Tools required: Corded / Cordless Drill, 8mm Drill Bit, Adjustable Spanner, Pozi-drive
Bit / Screwdriver, 3mm Drill Bit required in order for you to drill all screw holes before
construction.
The colour version of this document can be downloaded from:
www.zest4leisure.co.uk/downloads/category/C1
Hollywood Swing with Canopy Pack List
Item Description Quantity
A Brackets 3
B Support Rails 3
C End Board 2
D Board 32
Fixings
40mm screws 102
60mm screws 12
70mm bolts 3
www.zest4leisure.co.uk

Please take a few moments to check all pack contents listed.
Assembly requires 2 persons.
Tools required: Corded/Cordless Drill, 8mm Drill Bit, Adjustable Spanner, Pozi-
drive Bit/Screwdriver, 3mm Drill Bit required in order for you to drill all screw
holes before construction.
Hollywood Swing with Canopy is now complete.
1. Position 1no Bracket A centrally along underside of 1no Support Rail B and fix
using 4no 60mm screws. (See Fig. 1)
Repeat procedure for remaining brackets and support rails. Ensure similar
orientation of brackets.
2. Begin at rear (See Fig. 1) and fix End Board C (groove uppermost) to topside of
2no Support Rails B using 2no 40mm screw (1no per end), ensuring 100mm
overlap at both ends beyond edges of Support Rails. (See Fig. 2a)
Position remaining 1no Support Rail B centrally along End Board C and similarly
fix using 1no 40mm screw. (Ensure all Brackets A are orientated correctly).
Interlock 1no Board D into End Board C to form an external overlap and fix to
Support Rails B using 3no 40mm screws (1no per support rail). Continue to
interlock and fix remaining 31no Boards D using 93no 40mm screws (3no per
board) ensuring 100mm overlap is maintained. (See Fig. 2b)
Interlock remaining End Board C and fix using 3no 40mm screws.(See Fig. 2c)
3. Position canopy onto beam of swing assembly, drill 8mm holes in beam (through
brackets) and fix using 3no 70mm bolts. (See Fig. 3) Fully tighten all nuts*.
*Nuts may need re-tightening periodically dependent on weather conditions.

www.zest4leisure.co.uk
2a
1
2b 2c
3a