ZKTeco SBTL5000 series User manual

User Manual
Swing Barrier SBTL5000 series
Applicable Models: SBTL5000/5200, 5011/5211, 5022/5222
Version: 1.1
Date: August 2019

I
Content
1. Product Introduction............................................................................................................................................................. 1
1.1 Model number and access control...................................................................................................................... 1
1.2 Chassis design and dimensions............................................................................................................................. 1
1.3 Mechanical system of the swing barrier........................................................................................................... 2
1.4 Electronic control system........................................................................................................................................... 2
1.5 The working principle of swing barrier............................................................................................................. 2
1.6 System composition of the product................................................................................................................... 3
1.7 Specification........................................................................................................................................................................ 4
2. Installation of the Product.................................................................................................................................................. 4
2.1 Installation notes.............................................................................................................................................................. 4
2.2 Installation position of the swing barrier......................................................................................................... 5
2.3 Cables installation and fixing................................................................................................................................... 5
3. Menu Introduction.................................................................................................................................................................. 7
3.1 Function introduction .................................................................................................................................................. 7
3.2 Menu introduction.......................................................................................................................................................... 7
3.3 Functions introduction of wiring and terminal.........................................................................................11
4. Troubleshooting.....................................................................................................................................................................12
5. Product Maintenance..........................................................................................................................................................13
5.1 Chassis maintenance...................................................................................................................................................13
5.2 Movement maintenance..........................................................................................................................................13
5.3 Power maintenance.....................................................................................................................................................13

SBTL5000 series User Manual Page | 1
1. Product Introduction
1.1 Model number and access control
Access
Model
None C3-200 and 2*Wiegand
reader
inBio 260 and 2*
FR1500/ID reader
SBTL5000 √
SBTL5011 √
SBTL5022
√
SBTL5200 √
SBTL5211 √
SBTL5222 √
1.2 Chassis design and dimensions
SBTL5000 series is with SUS304 housing, provides simple and beautiful design with anti-corrosion. It
provides legal access to the persons while eliminating illegal personnel access. In case of emergency,
it ensures that evacuation passage runs smoothly and is convenient for personnel.
SBTL5000’s appearance and dimensions are as shown in Figure 1-2:
Figure 1-2

SBTL5000 series User Manual Page | 2
1.3 Mechanical system of the swing barrier
The mechanical system of a swing barrier turnstile includes the chassis and the core component. The
chassis is a carrier where the direction indicator, the reader, the Infrared sensor, and the door lock are
installed. The core component mainly consists of the motor, the frame, the belt, and the swing arm.
1.4 Electronic control system
The electronic control system of a swing barrier turnstile is mainly composed of the reader, the master
control panel, the access controller, the infrared sensor, the direction indicator, the alarm, and the
transformer.
Reader: The reader reads the data in the card and sends it to the controller.
Master control panel: The master control panel is the system’s control center that receives signals
from the reader and the photoelectric switch, performs logical judgment and processing of these
signals, and sends executive commands to the direction indicator, the electric motor and the alarm.
Infrared sensor: It detects the position of a pedestrian and plays the role of safety protection.
Direction indicator: This indicator displays the current status of the sign at the lane, and directs the
pedestrian to pass through the lane in a safe and orderly manner.
Alarm: The alarm gives an alarm voice if the system detects any unauthorized entry to the lane.
1.5 The working principle of swing barrier
After powered on, the system performs self-check. If no failure is detected, the machine starts
to operate normally. If a failure is detected, the system displays related messages on the LCD
display screen so that the user can have a quick knowledge of and solve the problem.
When the reader detects a valid card, the buzzer will give a nice audible prompt to the
pedestrian, indicating that the card is being read successfully. And then, the reader sends
signals to the access controller to request permission to pass through the lane. The access
controller will send the signal to the master control panel.

SBTL5000 series User Manual Page | 3
After receiving the signal from the access controller, the master control panel sends valid
control signals to the direction indicator and the electric motor. And the direction arrow turns
green.
Pedestrians passes through the lane according to the direction indicator signs, infrared sensors
detect the pedestrians pass through the whole process, and continue send signal to the
master control board until the pedestrian has been completely through the lane.
If the pedestrian enters the passage but forgets to flash the card read by the reader, or if the
card held by the pedestrian is invalid, the system will stop the pedestrian, and give an audible
alarm until the pedestrian retreats from the lane. The pedestrian can pass through the lane
only after a valid card is read by the card reader.
1.6 System composition of the product
The single-lane management system is composed of two single-core swing barrier turnstile. The
multi-lane management system is composed of two single-core barriers and multiple dual-core
barriers.
Working modes of the system
To meet the requirements of being used in different places, this system provides multiple working
modes for the user. Including normal working mode, normally open and normally close mode, testing
mode.
After powered on, the LCD screen on control board will display a default state, which displays
currently work mode.

SBTL5000 series User Manual Page | 4
1.7 Specification
Dimension(mm) SBTL5000 Series : L=1400, W=180, H=1000
Communication RS485 Input voltage AC100~240V, 50-60Hz
Input control signal Switching
signal
Output voltage DC 24V
Time of
opening/closing
0.8S(adjustabl
e)
Relative
humidity
20%-95%（Non-condensing）
Temperature -28℃-60℃Passage rate Maximum 30/minute
Infrared sensor 6 Working
environment
Indoor
2. Installation of the Product
2.1 Installation notes
1) It is recommended that the swing barrier turnstile be installed on a horizontal solid platform with
50mm to 100mm in height.
2) It is also recommended that the swing barrier turnstile should not be used in corrosive
environment.
3) Make sure the protective ground wire of the system is reliably connected to avoid personal
injuries or other accidents.
4) After installation, check whether connection is reliable at the connecting points of the protective
ground wire, at the connector assemblies and wiring points of the circuits, as well as at each
movable part of the swing barrier turnstile. Any loose nuts, screws and other fasteners should be
tightened in time to avoid swing barrier turnstile failures caused by long-time operations.

SBTL5000 series User Manual Page | 5
2.2 Installation position of the swing barrier
A distance of 100mm between the swing barrier turnstile and the wall needs to be reserved for ease
of opening the top cover of the machine to perform maintenance and adjustment. The reference
figure as below:
Figure 2-2 SBTL5000 series dual-lane
2.3 Cables installation and fixing
For the outlets of the concealed cables, please refer to the drawing showing the mounting holes. The
input voltage for this swing barrier turnstile is AC100-120V/200-240V and its master and slave are
connected by a 5-core cable (signal) and a 2-core cable (power). When installing this swing barrier
turnstile, the user only needs to connect it to the corresponding ports. Note that the PVC conduits are
buried 100mm under the ground, with the height of the exposed part not exceeding 100mm. In
addition, the conduit outlet is bent back to prevent ingress of water into the conduit.
SBTL 5000 series installation holes and cabling positions as shown in Figure 2-3a:

SBTL5000 series User Manual Page | 6
Figure 2-3a
Mark the screw hole centre of the stand, and the edge of the chassis base on the ground according to
the sizes as shown on the Figure 2-3a. Use a hammer drill to perforate M12 screw holes and then
install the screws. Place the swing barrier turnstile according to the sizes and positions as shown in
the figure before installation and fixing. Connect the online cables and perform the power-on test. If
the test is OK, tighten the screws. It is recommended that a warning line be marked out on the
ground after the machine is installed, so as to prompt the pedestrian to stand behind the warning line
when swiping the card. As shown in Figure 2-3b:
Figure 2-3b

SBTL5000 series User Manual Page | 7
3. Menu Introduction
3.1 Function introduction
1) After powered on, the LCD screen on control board will display a default state, which displays
current work mode.
2) There are 4 buttons 'UP, DOWN, ENT, ESC'on the control board, show as Figure 3-1:
UP: to move up menu item or increase the value.
DOWN: to move down menu item or decrease the value.
ENT: to enter menu setting item or confirm the current modified value.
ESC: to return to the previous menu or to cancel the current operation.
Figure 3-1
3) Operation and instruction of menu
Press the ENT button, enter the password input interface, the default password is: UP, UP, DOWN,
DOWN, DOWN, DOWN. If any step fails please press the ESC button to get back. After entering the
menu press UP or DOWN to choose a menu item and then press ENT to enter the interface and
adjust function or value.
3.2 Menu introduction
1. Barrier positioning
Zero position (Default).

SBTL5000 series User Manual Page | 8
Left opening position.
Right opening position.
2. Opening mode
Bi-direction swiping card. (Default)
Left free + Right swiping card.
Left swiping card + Right free.
Bi-direction control by IR sensor.
Left forbidden + Right swiping card.
Left swiping card + Right forbidden.
Left forbidden + Right free.
Left free + Right forbidden.
Bi-direction forbidden.
3. Open duration
5~60s (The default is 10s).
4. False direction entry
Close door and voice alarm.
Voice alarm (Default).
Alarm disabled.
5. Speed of barrier closing and opening
Low speed.
Middle speed (Default).
High speed.
6. Anti-tailgate
Alarm disabled.
Voice alarm (Default).
Close door and voice alarm.
7. Reset counter
Exit counter (Default).
Entry counter.
Both.

SBTL5000 series User Manual Page | 9
8. Gate closing delay time
0~10s (The default is 0).
9. Unlock brake
Delay to unlock (Default).
Unlock after card swiping.
10. Brake starting angle
3~10°(The default is 3°).
11. Fire signal setting
Right opening (Default).
Left opening.
Disable.
12. System working mode
Working mode (Default).
Test mode.
Factory reset.
13. Volume setting
Disable.
1~16 (The default is 5).
14. Exchange voice of door opening
No (Default).
Yes.
15. IR anti-pinch setting
Disable.
Stop turning for anti-pinch (Default).
Open the barrier for anti-pinch.
16. Memory function
Disable (Default).
Enable.

SBTL5000 series User Manual Page | 10
17. Select anti-pinch area
No anti-pinch (Default).
All IR areas for anti-pinch.
18. Master device speed compensation
0~20 (The default is 0).
19. Slave device speed compensation
0~20 (The default is 0).
20. Swiping card mode
Allow to swipe card in passage (Default).
Not allow to swipe card in passage.
21. Version
V6.0.3.

SBTL5000 series User Manual Page | 11
3.3 Functions introduction of wiring and terminal
1) Wiring diagram
Figure 3-2
2) Functions of terminals at each zone:
System power input: The mains voltage is changed by a transformer to 24V and supplied to the
master panel.
Firefighting board: After a power outage, the swing barrier of the machine is opened with power
from the backup battery and is no longer closed.
Right open (DOWN button), left open (UP button): Controls the barrier to open to left or right side.
Access control power supply: Supplies power for the access board.
RS485 communication port: Receiving external signals.
Master/slave terminal: It is connected to the master and slave boards to transfer signals.
IR-L：IR1
IR-R：IR4
AP-L：IR2
AP-R：IR3
IR1，IR4 at the bottom
IR2，IR3 on the top
LED light
LED light

SBTL5000 series User Manual Page | 12
Electromagnetic clutch: It is connected to the electromagnet inside the core component to prevent
collision and pinch.
Connecting cable of the motor: It is connected to the motor and supplies power to the motor.
Left infrared detector, left anti-pinch/right infrared detector, right anti-pinch detector: It detects
the position of a pedestrian in the passage. It has the detecting and anti-pinch function.
Direction indicator board terminal: This terminal is connected to the LED board to indicate whether
or not the pedestrian can pass through the passage.
Firefighting port: During emergencies ensuring users fast unencumbered exit to safety.
4. Troubleshooting
Number Failure description Analysis and solution
1 No response from direction indicator
or indication is not correct.
Check whether the connection of the roof
lamp is correct or not.
2 After swiping the card there is only a
swing arm action.
Check the master and slave machine type
setting and the 5-core, 2-core connection
line.
3 Barrier open after a long time no
closing.
Check whether the time of the opening is
too long or the IR sensor is covered by
others.
4 Motor doesn’t rotating or the
resistance too great or belt loosen.
If the motor working properly, but the
rotated angle not enough, which may
caused by belt loosen. If can’t solve it, try to
increase the value of twelfth menu.
5 When power on, the swing arm can’t
turn back to the initial position
Ensure that no obstacle in the passway, then
restart the equipment.

SBTL5000 series User Manual Page | 13
5. Product Maintenance
5.1 Chassis maintenance
The chassis is made up of 304 stainless steels. There may be rust stains on its surface after being used
for a long time. Regularly sand the surface along the grain softly and carefully. Coat the surface with
anti-rust oil, do not cover the infrared sensor.
5.2 Movement maintenance
Cut off power supply before maintenance. Open the door, clean surface dust, apply butter to the
transmission mechanism. Check whether the belt is loose, if found loose, adjust the position of the
motor to make the belt tight. Check and tighten others connection parts.
5.3 Power maintenance
Cut off power supply before maintenance. Check whether the plug is loose, if found loose, tight it. Do
not replace the connection position at random. Check whether the external power supply is exposed,
timely wrap it. Whether there is any leakage, do timely treatment. Check if the technical parameters of
interface is normal, the aged electronic components should be replaced.
(Attention: Above swing barrier maintenance must be maintained by professional personnel.
Especially the movement and the electric control part, first cut off the power supply, ensure the
operation safety.

Copyright©2019 ZKTECO CO., LTD. All rights reserved.
ZK Building, Wuhe Road, Gangtou, Bantian, Buji Town,
Longgang District, Shenzhen China 518129
Tel: [phone]
Fax: [phone]
www.zkteco.com