Roger MCT12E User manual

MCT12E MCT64E MCT66E Installation Manual.doc 2018-03-06
1/2
Roger Access Control System
MCT12E / MCT64E / MCT66E Installation Manual
Firmware version: 1.0.2 and newer
Document version: Rev. A
This document contains minimum information that is necessary for initial setup
and installation of the device. The detailed description of configuration
parameters and functionalities is specified in respective Operating manual
available at www.roger.pl.
INTRODUCTION
The MCT reader is designed to operate in RACS 5 system as peripheral device
connected to RS485 bus of MC16 access controller. Factory new reader is
configured with default settings including ID=100 address. Before connecting to
controller, the reader should be assigned with unoccupied address in range of
100-115. Programming of other parameters depends on the individual
requirements and is not obligatory. Addressing of the reader can be done from
computer by means of RogerVDM program or manually within memory reset
procedure. Configuration of the reader with RogerVDM requires RUD-1 interface.
CONFIGURATION WITH ROGERVDM PROGRAM
The configuration requires connection of reader to computer with RUD-1
interface (fig. 1) and starting RogerVDM software.
Fig. 1 Connection of MCT reader to RUD-1 interface
Programming procedure:
1. Connect the reader to RUD-1 interface (fig. 1) and connect the RUD-1 to
computer’s USB port.
2. Start RogerVDM program, select MCT device, firmware version, RS485
communication channel and serial port with RUD-1 interface.
3. Click Connect, the program will establish connection and will automatically
display Configuration tab.
4. Enter unoccupied RS485 address in range of 100-115 and other settings
according to requirements of specific installation.
5. Click Send to Device to update the configuration of reader.
6. Optionally make a backup by clicking Send to File… and saving settings to
file on disk.
7. In the top menu select Device->Disconnect.
8. Disconnect reader from RUD-1 interface.
Note: Do not read any cards nor press reader keypad when reader is configured
with RogerVDM.
MEMORY RESET PROCEDURE
Memory reset procedure enables configuration of RS485 address and resets all
other settings to factory default ones.
Memory reset procedure:
1. Remove all connections from A and B lines.
2. Connect CLK and DTA lines.
3. Restart the reader (switch power supply off and on or short RST contacts for
a moment).
4. When red LED STATUS, green LED OPEN and orange LED SYSTEM are on
then disconnect CLK and DTA lines.
5. When orange LED SYSTEM is on then enter 3 digits of RS485 address in
range of 100-115 with reader keypad or with any EM125kHz proximity card.
6. When the third digit is defined then the reader will restart with the new
address.
Readers without keypad can be addressed with multiple card readings where the
N number of readings emulates digit of the address. Three series of readings
with any EM125kHz proximity card are necessary to set the address. After each
series wait for two beeps and proceed with the next digit. Zero digit is emulated
with 10 readings.
Example:
Programming of ID=101 address with card readings:
1. Read card 1 time and wait for two beeps.
2. Read card 10 times and wait for two beeps.
3. Read card 1 time and wait for two beeps.
4. Wait till reader is restarted with the new address and other default settings.
FIRMWARE UPDATE
The update requires connection of reader to computer with RUD-1 interface
(fig. 1) and starting RogerISP software. The latest firmware file is available at
www.roger.pl.
Firmware update procedure:
1. Connect the reader to RUD-1 interface (fig. 1) and connect the RUD-1 to
computer’s USB port.
2. Place jumper on FDM contacts (fig. 2).
3. Restart the reader (switch power supply off and on or short RST contacts for
a moment).
4. Start RogerISP program.
5. Select serial port with RUD-1 interface and USB-RS485 Converter option.
6. Specify path to firmware file (*.hex).
7. Click Program and proceed according to displayed messages.
8. Remove jumper from FDM contacts and restart the reader.
APPENDIX
Fig. 2 Service contacts
Table 1. Terminals and wires
Screw
terminal
Wire colour
(MCTxxE-IO)
Wire colour
(MCTxxE)
Description
12V
Red
Red
Supply plus
GND
Black
Blue
Ground
IN1
Pink
IN1 input line
IN2
Blue
IN2 input line
IN3
White-yellow
IN3 input line
RS485 A
Brown
Brown
RS485 bus, line A
RS485 B
Green-white
White
RS485 bus, line B
CLK
White
Green
CLK line
DTA
Green
Yellow
DTA line
TMP
Yellow
Pink
Tamper switch
TMP
Grey
Grey
Tamper switch
IO1
Yellow-brown
IO1 output line
IO2
Green-brown
IO2 output line
REL1-NC
Grey-pink
REL1 relay output
(NC)
REL1-COM
Red-blue
REL1 relay common
terminal
REL1-NO
Violet
REL1 relay output
(NO)

MCT12E MCT64E MCT66E Installation Manual.doc 2018-03-06
2/2
Fig. 3 Connection of readers and expanders to MC16 access controller
Fig. 4 Connection of door lock, door contact and exit button to MCTxx-IO reader
Table 2. Specification
Supply voltage
Nominal 12VDC, min./max. range 10-15VDC
Current consumption
(average)
MCT12E/MCT12E-IO: ~50 mA
MCT12E-BK/MCT12E-BK-IO: ~40 mA
MCT64E-IO: ~50 mA
MCT66E-IO: ~40 mA
Inputs
Three NO/NC inputs (IN1..IN3) internally
connected to the power supply plus through a
15kΩ resistor, approx. 3.5V triggering level
Relay output
Relay output (REL1) with single NO/NC contact,
30V/1.5A DC/AC max. load
Transistor outputs
Two (IO1, IO2) open collector outputs, 15VDC/1A
max. load
Tamper protection
Isolated 50mA/24V contacts, shorted when
enclosure is closed
Proximity cards
EM 125 kHz UNIQUE according to EM4100/4102
Reading range
up to 10 cm for MCT66E
up to 7 cm for remaining readers
Distance
1200m maximal cable length for RS485 bus
between controller and reader
IP Code
IP65
Environmental class
(according to EN 50133-1)
Class IV, outdoor general conditions, temperature:
-25°C to +60°C, relative humidity: 10 to 95% (no
condensation)
Dimensions H x W x D
MCT12E: 152,5 x 46 x 23(35) mm
MCT64E-IO: 115 x 80 x 35 mm
MCT66E-IO: 85 x 85 x 27 mm
Weight
~150g
Certificates
CE
This symbol placed on a product or packaging indicates that the
product should not be disposed of with other wastes as this may
have a negative impact on the environment and health. The user is
obliged to deliver equipment to the designated collection points of
electric and electronic waste. For detailed information on recycling,
contact your local authorities, waste disposal company or point of
purchase. Separate collection and recycling of this type of waste
contributes to the protection of the natural resources and is safe to
health and the environment. Weight of the equipment is specified in
the document.
Contact:
Roger Sp. z o. o. sp. k.
82-400 Sztum
Gościszewo 59
Tel.: [phone]
Fax: [phone]
Tech. support: [phone]
E-mail: [email protected]l
Web: www.roger.pl