ZKTeco HBL100 User manual

Installation Guide
HBL100/HBL200 (Double Latch)
Version: 1.0
Date:June2019

What’s in the Box..........................................................................................1
Installation Diagram...................................................................................2
Installation Preparation..............................................................................3
Installation Steps.........................................................................................4
Change Handle Direction.........................................................................11
Important Notes
Contents
vPlease read all instruction in this manual or call customer care before returning the product to the store.
vThe contents of this guide may vary without any notices to improve the performance of this product.
vCustomer's improper installation may result in a additional service costs. We highly recommend
professional installation.

30-37mm 38-45mm 46-53mm 54-60mm
Spindle
Screw A
Screw B
Screw C 40mm
Note: To ensure proper functioning of the lock, use the correct set of screws and spindle according
to your door thickness.
8mm
64mm 72mm 80mm 88mm
What’s in the Box
Door Thickness
Outdoor unit Indoor unit
Keys
Hex wrench
Latch
Strike
plate Strike
box
GasketMounting
plate Lithium Battety
1

Installation Diagram
Keys
Outdoor unit
Gasket
Latch
Screw A
Strike
plate
Strike
box
Gasket
Mounting
plate
Screw C
Spindle
Indoor unit
Screw B
Door
Battery Cover
Lithium battery
Cover
2

Left inward Right inward
Left outward Right outward
Standpoint
Latch
Strikeplate Latch
Strikeplate
Latch
Latch
Strikeplate
Strikeplate
Installation Preparation
2. Check door opening direction.
The handle of the door is determined by the swing (handing) direction of the door. Below is the graphical
representation of handing in reference to your location outside the room.
1. Check door thickness.
After measuring the door thickness, select the proper spindle and screw length. For details, please refer to
the table contents of page 1.
3

center line of handle
RecommendedInstallationHeight 1. Drilling holes in the door.
1) Paste the installation template at a desired handle
height.
2) Mark the holes and start drilling the holes.
Installation Steps
If the user height is 1.6-1.8m, the height
from handle centerline to ground is 1m.
1.0m
0.5m
desired handle height
30~60mm
60mm
4

2
1
Secure the latch by inserting the screws A.
Change latch direction. (if needed)
1. Push the reversing block down.
2. Push the latch bolt into mortise.
3. Rotate the latch bolt at 180° inside
mortise, then loose it.
1
2
3
Screws A
2. Installing the latch.
5

12
1. Attach the gasket to the outdoor unit.
2. Insert spindle into the clutch.
Route cable and attach the outdoor unit to the door
by inserting it through the drilled holes.
Clutch c orrect p osition:
T he triangle must be vertically centered.
3. Installing outdoor unit on the door.
6

2
1
Attach the mounting plate to the gasket and route
the cable through the hole on the mounting plate
and gasket.
Place the gasket and mounting plate on to
the door and use screws C to secure them.
Screws C
4. Installing mounting plate with gasket on the door.
7

2
1
Connect the cable connector to the port on indoor unit. Place the indoor unit properly on the
mounting plate. Then use screw B to
secure indoor unit.
Screws B
5. Installing the indoor unit.
8

1. Make sure that the strike box is in level of latch bolt, then use
installation template to drill holes.
Align the strike box and plate with the drilled hole and use 2.
screws A to secure them.
Insert the lithium battery and
install the battery cover.
Note: Eight alkaline batteries are
optional.
Screws A
6. Insert batteries.7. Mark and drill holes for the strike box and plate.
9

2
1
Test the lock from outdoor by rotating the
handle.
Note : When the door is l ocked , the front
handle can be turned, but the door will
remain locked.
Test the lock by using the mechanical key.
1) Remove the cover on the
mechanical key hole.
2) Insert the key and rotate
90° to the left or right.
3) Turn the handle
downward to open the door.
8. Testing the lock.
10

3) Change handle direction a nd replace.
4) Secure using the screw.
2
1
1) Use hex wrench to re move screw.
2) T ake the handle out from the lock.
Change Handle Direction
11

Copyright©2019 ZKTeco CO., LTD. All rights reserved.
ZKBuildingWuhe Road, Gangtou, Bantian, Buji Town,
Longgang District, Shenzhen China 518129
Tel: + 86 755-89602345
Fax: + 86 755-89602394
www.zkteco.com