ZKTeco X7 User manual

Version: 1.2.1

I
门磁
1. Equipment Installation
(4) Fix the device to the
back cover.
(5) Fix the screw.
(1) Remove the screw on
the bottom of device.
(2) Take away the back cover.
(3) Fix the back cover on the
wall according to the
mounting paper.
2. Structure and Function
Access Control System Function:
(1) When a registered user's identity is verified, the
Access Control device will send out signal to unlock
the door.
(2) The door sensor will detect the status of the lock. If
the door is unexpectedly opened or improperly
closed, the alarm will be triggered.
(3) It supports the exit button for opening the door
from inside.
(4) It supports door bell.
(5) If the Access Control device is dismantled, the alarm
will be triggered.
Tamper Alarm Button
Lock
Lock Sensor
Exit Button
Bell
Alarm

II
Warning:No operation when power on!
(1) The system supports NO LOCK and NC LOCK. The NO LOCK (normally open at
power on) is connected with NO terminal, and the NC LOCK is connected with NC
terminal.
(2) To prevent the generation of self-inductance EMF which would affect the system,
when the electrical lock is linked to the Access Control System, it is required to
connect one FR107 diode (equipped in the package, do not reverse the polarities) in
parallel in order to release the self-inductance EMF.
(1) Device shares power with the lock (2) Does not share power with the lock
+12V
GND
BUT
GND
SEN
COM1
NC1
AL-
AL+
BELL-
BELL+
NO1
-
+
-
++
-
DC12V
+12V
GND
BUT
GND
SEN
COM1
NC1
AL-
AL+
BELL-
BELL+
NO1
-
+
-
++
-
DC12V
-
+
DC12V
I: device’output current, ULOCK: lock voltage, ILOCK: lock current.
(3) One device controls one lock
+12V
GND
BUT
GND
SEN
COM1
NC1
AL-
AL+
BELL-
BELL+
NO1
+
-
+12V
GND
NC
PUSH
NO
GND
V1+ V1-
NC Lock
Exit Button
Access Control Device
Professional Access Control Power Supply
When Device sharepower with the lock:
ULOCK=12V, I-ILOCK >1A… 
and the lock is nearto the device.
Devicedoes not share powerwith the lock:
A.When ULOCK =12V I-ILOCK ≤1A;
B.When ULOCK ≠12V;
C. When the lock is far apart from thedevice.
3. Lock Connection
NC Lock
NC Lock

III
Only devices with an alarm ≤ DC 12V can be connected.
Input DC 12V, 500mA (50mA in idle status) Positive is connected with
+12V, negative is connected with GND (do not reverse the polarities).
4. Connected with Other Devices
5. Connect with Power

Βιομετρικός Ελεγκτής SA-X6
Ο βιομετρικός ελεγκτής SA-X6 υποστηρίζει κλειδαριές NO Lock & NC Lock.
Προσοχή: θα πρέπει παράλληλα με το φορτίο (κλειδαριά) να συνδεθεί μία δίοδος
FR107, όπως φαίνεται στο σχήμα για προστασία από EMF.
1. User management
1.1 Administration Operations
For the security the data, admin password is needed to operate the machine.
 Register the admin fingerprint
Press [*]+[#]→Input [1234#]→register fingerprint 3 times (green light on and a
long buzz) →press [*] to exit (green light on and a long buzz)
 Modify the admin fingerprint
Press [*]+[#]→Press admin finger print → press [8] (green light on and a long
buzz) →register fingerprint 3 times → press [*] to exit (green light on and a long
buzz)
1.2 Add/Edit a User -Προσθήκη/επεξεργασία Χρήστη
Each user can register 10 fingerprint and 1 card/Tag at most.
Press [*]+[#]→ press admin finger print → press [#]→ Input a new/ existing work
code (user ID 1-8) → [#]→ register user fingerprint 3 times (green light on and a
long buzz) OR register user CARD or TAG →press [#] continue to add new users
OR press [*] to escape (green light on and a long buzz).
Notice:
a. New user has to put work code (user ID), the machine will defultly edit the present
user if the number existed.
b. After the first fingerprint registered, same user's other fingerprints can be added,
10 pieces at most
c. If there is wrong action or repeat occurred suring register fingeprint/ cards,
machine's red light will be on along with short buzz 4 times, then green light will be
on. Continue to register without exit, no operation limits.
1.3 Register 8 group open password.
Device maximum support 8 group open door password, each password with 1 group
(range:1-8).
Press * + # -- Administrator finger--Press 3 input group number (1-8) ---input 4 digits
password # (repeat it 2 times) Press * exit.
1:How to delete single user?
Answers: press * # press administrator finger (Green light blink) press 2 (Green light
blink)=input staff's ID number ---press finger or punch RFID cards. press * exit.

Remark: when we enrol users, we need to input staff's ID number such as : 001 and
then press finger or punch cards...
2:How to delete all users?
Press * + # - Press administrator finger -- Press 9 + # ---- Press * to exit.
3:Setup verify mode (factory FP/PW/RF)
Press * + # -- Press Administrator finger - Press 5---input verify mode number # and
press * exit.
Verify mode number:
PW: 1 RF:2 FP:3 FP/PW/RF:4 RF&PW:5 FP&PW:6
4:how to setup alarm?
illegal way to remove the device to alarm...or administrator with wrong finger to
setup alarm, or input wrong password etc.
Press * + # -- press administrator Finger ---Press 0 + 1 ----setup alarm swtich (0 :
open) (1 : close) press o or 1 and press # and press * to exit
5:how to set up door open delay time? Factory default is 6 seconds
Answers: Press * # press administrator finger -press 4, input door open time (1-10s)
press * exit
6:How to delete all users/reset to factory default?
Press * + # --- Press administrator finger -- Press 9 + # and press * to exit
7:How to delete administrator?
Open the back side cover, and press tamper switch with 3 times within 30-60
seconds.

9