ZKTeco Green Label ProCapture-T User manual

ProCapture-T Installation Guide 1
INSTALLATION GUIDE
ProCapture-T
Version: 1.1
Date: September 2021

ProCapture-T Installation Guide 1
Safety Precautions
Before installation, please read the following safety precautions for user
safety and to prevent product damage.
Do not install the device in a place subject to direct sun light, humidity, dust
or soot.
Do not place a magnet near the product. Magnetic objects such as magnet,
CRT, TV, monitor or speaker may damage the device.
Do not place the device next to heating equipment.
Do not to let liquid like water, drinks or chemicals leak inside the device.
Do not let children touch the device without supervision.
Do not drop or damage the device.
Do not disassemble, repair or alter the device.
Do not use the device for any purpose other than those specified.
Clean the device often to remove dust on it. In cleaning, do not splash water
on the device but wipe it out with smooth cloth or towel.
Contact your supplier in case of a problem!

2 ProCapture-T Installation Guide
Device Overview

Not all products have fingerprint or card function, the real product
shall prevail.

ProCapture-T
Camera
2.4-Inch Color Screen
Touch Keypad
Doorbell & LED Indicator
Fingerprint Sensor & Card
Reader Area
USB Slot
Reset Button
Front
Left Side

ProCapture-T Installation Guide 3
Device Overview
8 Pin Cable Connectors
4 Pin Cable Connectors Ethernet
2 Pin Cable Connectors
7 Pin Cable Connectors
12 Pin Cable Connectors
Tamper Alarm Button
RS485
RS232
Wiegand Out
Beep, LED
Wiegand In
Power Out
Power In
Alarm
Lock
Exit Button
Door Sensor
Doorbell
Auxiliary In

4 ProCapture-T Installation Guide
Product Dimensions & Installation

Product Dimensions
Mounting the Device on Wall
7.70 in
(195.5 mm)
3.43 in
(87 mm)
1.38 in
(35mm)
7.34 in
(186.5 mm)
3.0 in
(76.1 mm)
Fix the back plate onto the wall using wall mounting screws.
Note: We recommend drilling the mounting plate screws into solid
wood (i.e. stud/beam). If a stud/beam cannot be found, use supplied
drywall plastic anchors.
Insert the device to back plate. Use security screws to fasten the
device to back plate.
0.51 in
(13 mm)

ProCapture-T Installation Guide 5
Power Connection
Without UPS
With UPS (Optional)
Recommended Power Supply
GND
+12V
12V DC Adaptor
GND
+12V
12V DC Adaptor
12V±10%, at least 500MA.
To share the power with other devices, use a power supply with higher
current ratings.

6 ProCapture-T Installation Guide
Ethernet Connection
LAN Connection
Network Cable Adaptor
Ethernet Cable

ProCapture-T Installation Guide 7
Ethernet Connection
Direct Connection
Network Cable Adaptor
Ethernet Cable

8 ProCapture-T Installation Guide
RS485 Connection
RS485 Fingerprint Reader Connection
RS485 Fingerprint Reader
DIP Settings
1. There are six DIP switches on the back of RS485 fingerprint reader,
switches 1-4 are for RS485 address, switch 5 is reserved, switch 6 is for
reducing noise on long RS485 cable.
2. If RS485 fingerprint reader is powered from the terminal, the length of
wire should be less than 100 meters or 330 ft.
3. If the cable length is more than 200 meters or 600 ft., the number 6
switch should be ON as below.

ProCapture-T Installation Guide 9
Lock Relay Connection
Device Not Sharing Power with the Lock
COM1 +12V
GND
GND
Sensor NC1
FR107
Diode
12V DC Adaptor
Normally Closed Lock
Notes:
1. The system supports NO LOCK and NC LOCK. For example the NO
LOCK (normally opened at power on) is connected with 'NO1' and
'COM1' terminals, and the NC LOCK (normally closed at power on) is
connected with 'NC1'and 'COM1' terminals.
2. When electrical lock is connected to the Access Control System, you
must parallel one FR107 diode (equipped in the package) to prevent
the self-inductance EMF from affecting the system.
Do not reverse the polarities.
GND

10 ProCapture-T Installation Guide
Lock Relay Connection
Device Sharing Power with the Lock
COM1
+12V
Sensor NC1
GND
GND

ProCapture-T Installation Guide 11
Wiegand Output Connection
WD1
WD0 GND

12 ProCapture-T Installation Guide
Standalone Installation
Ethernet
Exit Button
Doorbell
Lock
Door Sensor
RS485 Fingerprint
Reader

ProCapture-T Installation Guide 13
Third Party Controller
Wiegand Output Connection
Ethernet
Wiegand
Output
Wiegand
Output
Wiegand
Output
Wiegand
Output
Outside Inside Lock Lock Inside Outside

14 ProCapture-T Installation Guide
How Does It Work
Fingerprint Registration Identification
Fingerprint Database
Verification
Event Log Stored
Verification Fails
Please try
again!
Granted
Thank You!
Door Opens

ProCapture-T Installation Guide 15
How to Place a Finger on Scanner
Note: ZKTeco’s fingerprint readers will give optimal results for fingerprint
matching, if the following recommendations and suggestions are followed.
Select a finger to enroll
It is recommended to use an index finger or a
middle finger.
Thumb, ring or little finger are relatively difficult to
place in the correct position.
How to place a finger on a sensor
Place a finger in a way that it completely covers the
sensor area with maximum contact.
Place the core of a finger at the center of the sensor. The
core of a finger is the center where the spiral of ridges is
dense (usually the finger core is at the opposite side of
the lowest point of the nail).
Place a finger in a way that the bottom end of a nail is
located at the center of the sensor.
DO NOT place the finger in the following positions
Upright Skewed
Sideways Partial

16 ProCapture-T Installation Guide
Tips
Tips for different fingerprint conditions
ZKTeco’s fingerprint products are designed to verify fingerprints with the
highest security irrespective of the skin conditions of finger. However, in
case a fingerprint cannot be read on the sensor, please refer to the
followings tips:
If a finger is stained with sweat or water, scan it after wiping the
moisture off.
If a finger is covered with dust or impurities, scan it after wiping them
off.
If a finger is too dry, try to exhale air onto your fingertip.
Tips for fingerprint enrollment
In fingerprint recognition, enrollment process is very important. When
enrolling a fingerprint, please place the finger correctly.
In case of low acceptance ratio, the following actions are recommended:
Delete the enrolled fingerprint and re-enroll the finger.
Try another finger if it is not easy to enroll a finger due to scar.
In case an enrolled fingerprint cannot be used due to injury or the hand
being full, it is recommended to enroll more than two fingers per user.

ProCapture-T Installation Guide 17
Troubleshooting
1. Fingerprint cannot be read or it takes too long?
Check whether the finger or fingerprint sensor is stained with sweat,
water or dust.
Retry after wiping off finger and fingerprint sensor with dry paper tissue
or a mildly wet cloth.
If the finger is too dry, exhale air onto it and retry.
2. “Invalid time zone” is displayed after verification?
Contact Administrator to check if the user has the privilege to gain
access within that time zone.
3. Verification succeeds but the user cannot gain access?
Check whether the user privilege is set correctly.
Check whether the lock wiring is correct.
Check whether anti-passback mode is in use. In anti-passback mode,
only the person who has entered through that door can exit.
4. The Tamper Alarm rings?
To cancel the triggered alarm mode, carefully check whether the device
and back plate are securely connected to each other, and reinstall the
device properly if necessary.

ProCapture-T Installation Guide 1
ZKTeco Industrial Park, No.32, Industrial Road,
Tangxia Town, Dongguan, China
Tel: [phone]
Fax: [phone]
www.zkteco.com
Copyright©2021 ZKTECO CO., LTD. All rights reserved.