ZMODO KW-0005 User manual

QUICK
START GUIDE
WIRELESS SECURITY SYSTEM

Congratulations on the purchase of your NVR system.
This quick start guide will assist you on getting your system up
and running as soon as possible. We recommend that you
connect everything and give it a try before you do a permanent
installation, to make sure nothing was damaged during
shipping.
WiFi antenna
Image sensor & lens
Infrared LEDs
1Introduction
Getting to Know Your NVR System:
2
5
6
5
6
1
For the Outdoor WiFi IP camera:
Weatherproof housing
Adjustable bracket
Mini USB power connector

For the MINI NVR
NVR Power Connector
Reset
USB
HDMI
LAN
HDD Installation
3
2

HDMI - Connect to your HDTV or computer monitor with an
HDMI port.
LAN - This is for connection to your home network so you
can connect from the internet.
USB - For connecting your USB mouse to control the
NVR, and also for you to back up the video from the
NVR. If you want to control USB mouse and USB
backup simultaneously at the back of the NVR,
please insert an external USB 2.0 hub with at least 2
ports.
What does this mean?
4
Once connected, place the HDD into the NVR with
the cables inside the NVR case, and cover the HDD
with the buffer rubber.
Make sure your NVR is unplugged from its power
source, and unscrew the four screws at the cover at
the bottom panel with a Philips screw driver.
Slide the cover off, and connect the SATA power and
data cables from the NVR to the corresponding ports
on your HDD.
Slide the bottom panel back on. Line up the holes on
the hard drive with the holes on the NVR cover, and
screw the four screws (found in kit) into the holes
using a Philips screwdriver.
When you power on your system and connect the
system to a monitor, you will see a popup on the
monitor asking you to format your HDD. Press [OK]
and wait 5-10 minutes. NOTE: If you do not see this
popup, please manually format your HDD by going
to the Disk Drive Info page.
3

Mini USB power connector - This is where you
connect the cameras in the kit to DC power supply.
Connect a monitor using the HDMI connection. Insert
one side of the HDMI cable into the back of the
monitor, the other side into the back of the NVR back
panel. (HDMI cable may not be provided).
Insert the provided 1M network cable to connect the
NVR to your router.
Plug the USB mouse (Not provided) into one of the
USB port.
Connect the NVR power adapter to your NVR directly.
And powers on the NVR.
Connecting Your NVR System
5
Fasten the four WiFi antennas to the back of the
included four cameras.
5
Note: this is necessary for mobile setup before
actual installation.
Connect the four cameras to the included four
camera power adapters, and plug the power
adapters to a power source.
6
NVR Power Connector - This is where you connect
the NVR's DC power supply.
4

Set up with Mobile Devices
6
It helps you connect the NVR and cameras to your
WiFi network, and also allows you to access your
NVR system from any location with available
network using any Android or iOS mobile devices
with our “MeShare” App installed.
The following images are captured from the iOS
version of the mobile app, the Android app works in
the same way.
TM ®
Connect your Android phone or iPhone to the WiFi
network that you want your camera to use. Make sure
that you know the password to connect to this
network.
System Requirements: Android™ (v.2.3 or newer) or
® ® ®
iPhone , iPad , iPod touch (v6 or newer) ,a
password-protected 2.4GHz WiFi network.
Mobile setup is necessary before you actually
install the cameras to your target area.
Download and install the ‘MeShare’ app from
TM TM
Google Play or the App Store . Launch the app
and sign up for a free MeShare account.
5

MeShare
6

Log in and press the Add
Device option located on the
bottom of the screen.
Tap “Ready” to start
searching the NVR devices
in your network.
7
Name your device and
tap” Finish”.
6
Found the NVR devices.
Tap “ADD”.
ZM-SS7008D4
(+08:00)Beijing,Urumqi,chongqing,H...

8
Enter the WiFi password in LAN,
make sure you saw the IP
camera's status indicator in this
kit is changing from sold green
to blinking green and tap
“Next”.
8
7Now the app will pop out a
message that “this kit has
wireless cameras that need to
be configured”, tap “OK” (in
Android) or “Set up wireless
cameras” (in iOS) to connect
with the wireless IP cameras in
the kit.
5454SDBDF455655
(+08:00)Beijing,Urumqi,chongqing,H...

9
9Now the NVR will start WiFi connection searching. The
result will be shown as a completed circle.
For the kit with four cameras, the circle will show four
cameras are connected successfully. Click “Finish” to
finish the mobile setup.
4
4