Zodiac AX20 ACTIV User manual

1. Clean the weir basket, pump basket and clean the lter before installing the
cleaner.
2. Always disconnect the cleaner from the Weir/Skimmer Box before cleaning or
backwashing the pool lter.
3. After cleaning or backwashing, let the ltration system run for at least ve (5)
minutes before re-connecting the cleaner.
4. Remove the cleaner from the pool before chemical or shock treatments.
5. Wait a minimum of four (4) hours after super chlorination before re-installing the
cleaner.
Assemble the Hoses
2
Before You Start
1
WARNING
Determine Required Hose Length
3
1. Temporarily disconnect hose from skimmer.
Turn on pool lter pump.
2. Flood the hose with water by placing the
end in front of one of the pool water return
inlets.
3. Turn o pool lter pump, reconnect hose to
skimmer, attach cleaner, and then turn pool
lter pump back on.
4
Connect to Weir
6
x 1
x 7
Read owner's manual
completely before
operating.
Do not operate cleaner
outside of pool.
Do not let children play
with cleaner.
Ensure all return lines point toward the
bottom of the pool.
Measure the hose length to the furthest
point of the pool plus one hose.
Submerge the Cleaner
Connect the Weir Fittings
5
90oElbow
Insert Into the Weir
Automatic Weir Valve
Male Hose Cu
Into Automatic Pool Cleaner
(APC)
a
c
g
e
x 1
x 11
x 1
f
x 1
d
b
x 1
h
1. Connect 90 degree elbow.
2. Connect Weir Valve.
3. Add hose protector to the hose.
4. Place hose in one half of hose protector.
5. Place the other half over hose ensuring male clips line up with the female clips.
NOTE: Before connecting to the weir
valve, ensure that all the hoses are
lled with water and all the air has been
expelled.

Quick Start Guide
WARNING
RISK OF SUCTION ENTRAPMENT HAZARD WHICH, IF NOT AVOIDED, CAN RESULT IN SERIOUS INJURY
OR DEATH.
READ THIS QUICK START GUIDE IN ITS ENTIRETY BEFORE INSTALLING AND OPERATING THE CLEANER.
Do not block the suction fittings in the pool, the suction opening on the cleaner, or the cleaner hoses with any part
of your body. Do not expose your hair, loose clothing, jewellery, etc, to any suction outlet fittings in the pool / spa or
on the cleaner.
For completeoperating instructions, please
downloadthe manual from the website, callthe
customer service number or submit a written
request to:
Fluidra Waterlinx (PTY) LTD
5 Kruger Street, Denver
Johannesburg
2094
0860 887 665
www.zodiac.co.za
©2020 ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license.
H0680500 REVC
Check Cleaner Flow
7
IF
20-25
10-19 Possible Damage Decrease Flow
+
_
Time is ...
26-50
Result ... Adjust Flow ...
Poor Performance Increase Flow
seconds
10 rotations
1. Watch the wheel speed indicator tab.
2. Use a stopwatch to time ten (10) wheel
rotations.
3. If wheels change direction during timing,
start over.
Adjust Auto Weir Valve
8
If the cleaner moves too fast and/or
climbs above the level of the pool water,
reduce Auto Weir Valve to medium (2) or
low (1) setting.
If the cleaner is moving slowly and/or not
climbing the pool walls, increase Auto Weir
Valve to medium (2) or high (3) setting.
This end plugs
into the weir
90oElbow
attaches to
this end
123
2