Zodiac T5 Duo User manual

Zodiac is a registered trademark of Zodiac Group Australia Pty Ltd
ABN 87 002 641 965
219 Woodpark Rd, Smitheld, NSW 2164 Australia
For more information visit www.zodiac.com.au
or call Customer Care 1800 688 552
RISK OF SUCTION HAZARD, WHICH IF NOT AVOIDED, CAN RESULT IN SERIOUS INJURY OR DEATH.
READ THIS GUIDE IN ITS ENTIRETY BEFORE INSTALLING AND OPERATING THE CLEANER. Do not block
the suction ttings in the pool, the suction opening on the cleaner, or the cleaner hoses with any part of your body.
Do not expose your hair, loose clothing, jewellery, etc, to any suction outlet ttings in the pool/ spa or on the cleaner.
For complete installation instructions, download the owner’s manual from the website www.zodiac.com.au or
call the Customer Service Centre 1800 688 562.
Start to orientate the return line (s) down towards the walls so the water is divided.
1Example of a pool with 1 return line Example of a pool with 2 return lines
Cleaner Body
AD Flow Valve
Universal Weir Cu
Hose mesh
Hose Weight
Pool Pulse™
Hose Section
Wheel Deector
Quick Connector


 



 
Install the AD Flow valve into the skimmer box. The way you connect the AD ow valve varies depending on the type
of skimmer you have.
2
1st case: with Waterco skimmer box
Screw the AD FlowValve connector
into the top of the Vac Plate.
2nd case: with Poolrite skimmer box
Screw the AD FlowValve connector
into the bottom of the Vac plate.
3rd case: with other types of skimmer box
AD Flow valve
Universal Weir Cuff
Assemble the hose sections, starting from the skimmer box until you reach the furthest point of your pool and add
2 extra sections. Add the hose weight on the last hose section as per the drawing below.
Connect the hose to the valve in the skimmer box.
Submerge the whole hose under water until there is no air left in the hose.
3
H0386300 REV A
QUICK START GUIDE
TM

Zodiac is a registered trademark of Zodiac Group Australia Pty Ltd
ABN 87 002 641 965
219 Woodpark Rd, Smitheld, NSW 2164 Australia
For more information visit www.zodiac.com.au
or call Customer Care 1800 688 552
Keep the hose under water and attach the ring by inserting the end of the cleaner hose through the outer ring.
Then push the quick connector over the hose.
4
Then connect the Pool Pulse™ by pushing the connector onto the pipe until it clicks in place. Turn on the pool pump
to measure the suction ow.
For best performance the Pool Pulse™ needs
to read 2.5
Once this step is achieved, you can disconnect
the Pool Pulse™ from the leader hose.
5
NOTE:
If Pool Pulse™ reads less then 2.5, then increase AD Flow Valve setting at 3 to increase suction ow.
If the Pool Pulse™ reads more than 2.5, then decrease the AD Flow Valve setting at 1 to decrease suction ow.
Extremity of the hose
with Wheel Deflecor
and Quick Connector. Pool
Pulse®
While still keeping the hose under water, attach the hose to the cleaner head by pushing the connector onto the pipe
until it clicks in place. Allow the cleaner to drift to the bottom of the pool.
Turn the pool pump on again, and your Zodiac cleaner is ready for cleaning, leaving you with a sparkling pool.
6To avoid any serious injury and before starting step 6, turn o the pool pump.
a. It is most important to disconnect the head of
the cleaner from the leader hose section when
you take the Zodiac cleaner out of the pool.
b. From time to time, ensure the diaphragm is free of debris
and / or dirt and rinse it with water. Simply disconnect the
top of the cleaner to access the diaphragm.
For care and maintenance
7