2N Helios IP Force User manual

2N TELEKOMUNIKACE a. s., Modřanská 621, 143 01 Praha 4, Czech Republic, tel.: [phone], fax: [phone],
e-mail: [email protected] IČO: 26183960, DIČ: CZ 26183960, Společnost je zapsaná v obchodním rejstříku vedeném Městským soudem
v Praze, oddíl B, vložka 6613. Č.Ú.: 51-1400870237/0100, 714154001/2400, 188430466/0300 www.2n.cz
How to install tamper switch to protect Helios IP against
unauthorized entry
This manual is valid for Helios IP Force and Helios IP Safety. You can use RFID card
reader as well as additional relay to place tamper switch!
Also mind that HW tamper switch can be used in Helios IP UNI, more info you can find in
installation manual of Helios IP UNI!
Since 2013 will be tamper switch attached to CPU, so you will have possibility to
configure function which will be started when activation tamper switch will be done,
more info in configuration manual!
1. As very first step you have to uncover front panel. Use torx screw 4 mm (Pic. 1). In
the (Pic. 2) see necessary accessories you will need during the installation.
Pic. 1 Pic. 2 Pic. 3
2. Then you need to remove key panel. Use cross-point screw driver.
Pic. 4

2N TELEKOMUNIKACE a. s., Modřanská 621, 143 01 Praha 4, Czech Republic, tel.: [phone], fax: [phone],
e-mail: [email protected] IČO: 26183960, DIČ: CZ 26183960, Společnost je zapsaná v obchodním rejstříku vedeném Městským soudem
v Praze, oddíl B, vložka 6613. Č.Ú.: 51-1400870237/0100, 714154001/2400, 188430466/0300 www.2n.cz
3. Remove screw stick and replace it by smaller one which you will find attached in box,
see (Pic. 2). After replacing of smaller screw stick (Pic. 3) place RFID card
reader/Additional relay to the connector (Pic. 5).
Pic. 5
4. In the (Pic. 6) you can see already placed RFID card reader (Additional relay can be
also used!!!).
Pic. 6

2N TELEKOMUNIKACE a. s., Modřanská 621, 143 01 Praha 4, Czech Republic, tel.: [phone], fax: [phone],
e-mail: [email protected] IČO: 26183960, DIČ: CZ 26183960, Společnost je zapsaná v obchodním rejstříku vedeném Městským soudem
v Praze, oddíl B, vložka 6613. Č.Ú.: 51-1400870237/0100, 714154001/2400, 188430466/0300 www.2n.cz
5. Then place key panel back. On the right side you can see connector for tamper switch
(Pic. 7).
Pic. 7
6. In the (Pic. 8.) you can see tamper switch placed.
Pic. 8

2N TELEKOMUNIKACE a. s., Modřanská 621, 143 01 Praha 4, Czech Republic, tel.: [phone], fax: [phone],
e-mail: [email protected] IČO: 26183960, DIČ: CZ 26183960, Společnost je zapsaná v obchodním rejstříku vedeném Městským soudem
v Praze, oddíl B, vložka 6613. Č.Ú.: 51-1400870237/0100, 714154001/2400, 188430466/0300 www.2n.cz
8. Once you will cover front plate, then two black buttons will be pressed, it will switch
on NO a C of the terminal block and close the circuit (Pic. 10). Since then if somebody
will try to entry the door IP intercom it will undo the circuit and send some information
to particular security localization (Pic. 11).
Pic. 9
Pic. 10 Pic. 11