3One data 1100 Series User manual

MODEL1100 Series
Media Converter
Quick Installation Guide
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website:
www.3onedata.com
Tel:
[phone]
Fax:
[phone]
【Package Checklist】
Please check whether the package and accessories are intact
while using the media converter for the first time.
1.
Media Converter (equipped with
terminal blocks)
2.
Certification
3.
Quick installation guide
4.
Warranty card
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
This series of products are media converters. Its models are
as follows:
Model I MODEL1100-5VDC (1 100M Copper Port + 1 100M
Fiber Port + 1 External 5VDC Power Supply)
Model II MODEL1100-220VAC (1 100M Copper Port + 1
100M Fiber Port + 1 Built-in 220VAC Power Supply)
Model III MODEL1100-48VDC (1 100M Copper Port + 1
100M Fiber Port + 1 Built-in 48VDC Power Supply)
【Panel Design】
Front view
Model I
Model II, Model III
Top view
Model I
Model II, Model III
Bottom view
Model I
Model II
Model III
Side view

Model I
Model II, Model III
1. Copper port rate status indicator
2. Fiber port rate status indicator
3. Copper port connection status indicator
4. Fiber port connection status indicator
5. Power supply indicator
6. Copper port working mode indicator
7. Hanger
8. 100M fiber port
9. 100M copper port
10. External DC round head power supply input
terminal
11. AC outlet
12. AC outlet switch
13. Built-in 48VDC power supply input terminal
【Mounting Dimension】
Unit: mm
Model I
Model II, Model III
Notice before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【Wall-mounting the Device】
Step 1 Put the device on the wall it will be mounted as
reference or to refer to its mounting dimension, and
mark the locations of 2 expansion screws.
Step 2 Put the device on the marked wall and tighten the
screws toward the marked locations, mounting
ends.
【Disassembling the Device】
Step 1 Device powers off
Step 2 Hold the device steady and unscrew the nuts on
the wall.
Step 3 Take out the device, disassembling ends.
Notice before powering on：
Power ON operation: first connect power line to the
connection terminal of device power supply, then power
on.
Power OFF operation: first unpin the power plug, then

remove the power line, please note the operation order
above.
【Power Supply Connection】
External 5VDC power supply
Model I provides external 5VDC power supply, DC
round head.
Built-in 220VAC power supply
Model II provides built-in 220VAC power supply,
and AC outlet with switch.
Power supply range: 85~265VAC.
Built-in 48VDC power supply
Model III provides 3-pin 5.08mm pitch
terminal blocks and built-in 48VDC power
supply.
【Checking LED Indicator】
The device provides LED indicators to monitor its operating
status, which has simplified the overall troubleshooting
process. The function of each LED is described in the table as
below:
LED
Status
Description
PWR
ON
PWR is connected and running
normally
OFF
PWR is disconnected and running
abnormally
Link/Act
（TX）
ON
Copper port has established valid
connection
Blinking
Copper port is in an active
network status
OFF
Copper port hasn’t established
valid connection
Link/Act
(FX)
ON
Fiber port has established valid
connection
Blinking
Fiber port is in an active network
status
OFF
Fiber port hasn’t established valid
connection
100(TX)
ON
Copper port rate is 100Mbps
OFF
Copper port rate is 10Mbps or it is
not connected
100(FX)
ON
Fiber port rate is 100Mbps
OFF
Fiber port is not connected
FDX
ON
Copper port is in full duplex mode
OFF
Copper port is in half duplex mode
【Specification】
Panel
100M copper port
10Base-T/100Base-TX
self-adaption
100M fiber port
100Base-FX fiber port
Indicator
Power supply indicator, fiber
port rate status indicator,
copper port rate status
indicator, fiber port connection
status indicator, copper port
connection status indicator,
copper port duplex indicator
Power supply
Model I
External 5VDC power supply,
DC round head
Model II
Built-in 220VAC (85~265VAC)
power supply, AC outlet with
switch
Model III
Built-in 48VDC power supply,
3-pin 5.08mm pitch terminal
blocks
Operating
environment
Operating temperature
-10~60℃
Storage temperature
-20~70℃
Operating humidity
5%~95% (no condensation)
Protection grade
IP30