ABB i-bus EIB/KNX AA/S 4.1 User manual

Product Manual ABB i-bus®EIB / KNX
Analogue Actuator AA/S 4.1
Analogue Actuator Module
AAM/S 4.1
Intelligent Installation Systems

This manual describes the function of the Analogue Actuator AA/S 4.1
and the Analogue Actuator Module AAM/S 4.1 with the application program
“Analogue output 4-8f /1.2”.
Subject to changes and errors excepted.
Exclusion of liability:
Despite checking that the contents of this document match the hardware and
software, deviations cannot be completely excluded. We therefore cannot
accept any liability for this. Any necessary corrections will be inserted
in new versions of the manual.
Please inform us of any suggested improvements.

1
Seite
1 General 2
1 General.................................................................................... 2
1.1 Product and functional overview............................................. 2
2 Device technology AA/S 4.1 3
2.1 Technical Data......................................................................... 3
2.1.1 Circuit diagram........................................................................ 4
2.1.2 Dimension drawing ................................................................. 5
2.1.3 Installation............................................................................... 5
3 Device technology AAM/S 4.1 6
3.1 Technical data ......................................................................... 6
3.1.1 Circuit diagram........................................................................ 7
3.1.2 Dimension drawing ................................................................. 8
3.1.3 Installation............................................................................... 8
4 Commissioning 9
4.1 Application program................................................................ 9
4.2 Parameter window .................................................................. 10
4.2.1 Parameter window “General Parameters” .............................. 10
4.2.2 Parameter window “Output X 1/2”.......................................... 11
4.2.3 Parameter window “Output X 2/2”.......................................... 13
4.3 Communication object............................................................ 15
4.3.1 Communication objects AA/S 4.1, Output 1-4........................ 15
4.3.2 Communications objects AAM/S 4.1, Output 5-8................... 17
5 Planning and application 19
5.1 Status displays........................................................................ 19
5.1.1 Analogue Actuator AA/S 4.1 ................................................... 19
5.1.2 Analogue Actuator Module AAM/S 4.1 ................................... 20
5.2 Use of 16-bit values ................................................................ 21
5.3 Use of 8-bit values .................................................................. 23
5.3.1 Dim actuator function.............................................................. 23
5.4 Forced control......................................................................... 24
5.5 Cyclical monitoring.................................................................. 25
A Appendix 26
Contents

2
ABB i-bus®EIB / KNX
The analog actuator converts measuring data received via EIB / KNX
telegrams into analog output signals. The analog output signals enable
heating, ventilation and air conditioning units to adapt their output values
to information received from the bus and thus to take part in control
processes.
Voltage signals: 0 ... 1 V DC
0 ... 10 V DC
Current signals: 0 ... 20 mA
4 ... 20 mA
The Analogue Actuator features four analogue outputs which can be
parameterised to a previously set format. Outputs which are not required
can be switched off. The output signals can be forced controlled.
The number of analogue outputs can be increased to 8 using the Analogue
Actuator Module AAM/S. When combined with the “Dimming” switch sensor
function the Analogue Actuator and the Analogue Actuator Module can be
used as an active control unit for dimming applications.
Note: The Analogue Actuator AA/S requires an external 24 V AC
voltage supply for operation. This voltage supply can also
simultaneously assume the supply of power to a connected
Analogue Actuator Module AAM/S.
1 General
1.1 Product and
functional overview
General

3
ABB i-bus®EIB / KNX
The Analogue Actuator converts measured data received via the EIB / KNX
to analogue output signals. The device features four outputs. The analogue
outputs can be used as current or voltage outputs with adjustable out-
put signals. The number of analogue outputs can be increased to 8 using
the Analogue Actuator Module AAM/S. The Analogue Actuator is a DIN
rail device for installation in the distribution board. The connection to the
EIB / KNX is established using a bus connection terminal. The device needs
an external 24 V AC power supply.
Device Technology
Analogue Actuator AA/S 4.1
2 Device technology
AA/S 4.1
Fig. 1: AA/S 4.1
2.1 Technical Data
Power supply Operating voltage 24 V AC ± 10 %
Bus voltage 21 … 30 V DC via EIB / KNX
Current consumption device / EIB / KNX Max. 310 mA / < 10 mA
Power consumption typ. 150 mW
Outputs 4 analogue outputs A1…A4 Extendable with Analogue Actuator Module
AAM/S to 8 outputs
Signal type 0 ... 1 V DC 0 ... 20 mA
0 ... 10 V DC 4 ... 20 mA
depending on parameterisation
Output signal load Voltage signal: 욷1 kΩ
Current signal: 울500 Ω
Output current Voltage signal Max. 10 mA per channel
Current signal Max. 20 mA per channel
Operating and display elements Device status display Status LED (3-colour: red, orange, green)
Output signal A1…A4 display Status LED (yellow)
Programming button and LED (red) For assignment of the physical address
Connections EIB / KNX Bus connection terminal (black/red)
Analogue outputs A1…A4
24 V AC power supply 2 screw terminals per output/terminal
Conductor cross-section:
single-core: 0.50 – 4.0 mm²
stranded: 0.34 – 4.0 mm²
stranded: 0.14 – 2.5 mm²
System connector, 6-pole Connection for max. 1 analogue actuator
module
Enclosure IP 20, EN 60 529
Ambient temperature range Operation – 5 °C ... + 45°C
Storage – 25 °C ... + 70°C
Transport – 25 °C ... + 70°C
Humidity Ambient/Storage/Transport Max. 93 % rel. humidity, no condensation
Design Modular installation device
Housing, colour Plastic housing, grey
Installation On 35 mm mounting rail to DIN EN 50 022
Dimensions 90 x 72 x 69.5 mm (H x W x D)
Mounting depth / width 70 mm / 4 modules at 18 mm
Weight approx. 180 g
Mounting position as required
Approvals EIB / KNX to EN 50 090-1, -2
CE mark in accordance with the EMC guideline and low
voltage guideline
2CDC 071 156 F0006

4
ABB i-bus®EIB / KNX
Note: The programming requires EIB Software Tool ETS2 V1.3 or
higher. If ETS3 is used a “.VD3” type file must be imported.
The application program is available in the ETS2 / ETS3 at
ABB/output/analogue output.
Fig. 2: Circuit diagram AA/S 4.1
1
2
3
4
Bus connecting terminal
Programming LED/button
Status LED output A1…A4
Status LED device
5
6
7
Connection terminals A1…A4
Connection for Analogue Actuator
Module
Connection terminal 24 V AC
2.1.1 Circuit diagram
Device Technology
Analogue Actuator AA/S 4.1
Application program Number
communication objects
Max. number of
group addresses
Max. number of
associations
Analogue output 4-8f /1.2 58 200 200

5
ABB i-bus®EIB / KNX
Fig. 3: Analogaktor AA/S 4.1
The connection to a max. of one Analogue Actuator Module is implemented
via a 6-pole system connector (included with the Analogue Actuator
Module).
쐌Do not connect electronic ballast’s or electronic
transformers with 1 – 10 V control input to the outputs!
쐌Do not connect external voltages to the outputs.
Connected components must ensure safe separation from
other voltages.
쐌The 0 V terminals must not be connected with the
terminals of the same designation of an Analogue Actuator
(risk of irreparable damage!).
쐌The 0 V terminals of outputs A5...A8 are internally
connected.
2.1.2 Dimension drawing
2.1.3 Installation
Device Technology
Analogue Actuator AA/S 4.1

6
ABB i-bus®EIB / KNX
The Analogue Actuator Module expands the Analogue Actuator AA/S 4.1
by four analogue outputs. The device converts measured data received via
the EIB / KNX to analogue output signals. The analogue outputs can be
used as current or voltage outputs with adjustable output signals.
The Analogue Actuator Module is a DIN rail device for installation in the
distribution board. For operation the 24 V AC power supply can be carried
out by AA/S 4.1.
Note: Programming of the Analogue Actuator Module AAM/S 4.1
is implemented via the application of the Analogue Actuator
AA/S 4.1. The programming requires EIB Software Tool ETS2
V1.3 or higher. If ETS3 is used a “.VD3” type file must be im-
ported. The application program is available in the ETS2 / ETS3
at ABB/output/analogue output.
3 Device technology
AAM/S 4.1
Fig. 4: AAM/S 4.1
3.1 Technical Data
Power supply Operating voltage 24 V AC ± 10 %
Current consumption Max. 120 mA
Current consumption on system connector Max. 6 mA
Outputs 4 analogue outputs Outputs A5…A8
Signal type 0 ... 1 V DC 0 ... 20 mA
0 ... 10 V DC 4 ... 20 mA
depending on parameterisation
Output signal load Voltage signal: 욷1 kΩ
Current signal: 울500 Ω
Output current Voltage signal Max. 10 mA per channel
Current signal Max. 20 mA per channel
Operating and display elements Device status displayStatus LED (red)
Output signal A5…A8 display Status LED (yellow)
Connections Analogue outputs A5…A8
24 V AC power supply
2 screw terminals per output/terminal
Conductor cross-section:
single-core: 0.50 – 4.0 mm²
stranded: 0.34 – 4.0 mm²
stranded: 0.14 – 2.5 mm²
System connector, 6-pole Connection to analogue actuator
Enclosure IP 20, EN 60 529
Ambient temperature range Operation – 5°C ... + 45°C
Storage – 25 °C ... + 70°C
Transport – 25 °C ... + 70°C
Humidity Ambient/Storage/Transport Max. 93 % relative humidity, no condensation
Design Modular installation device
Housing, colour Plastic housing, grey
Installation On 35 mm mounting rail to DIN EN 50 022
Dimensions 90 x 72 x 69.5 mm (H x W x D)
Mounting depth / width 70 mm / 4 modules at 18 mm
Weight approx. 150 g
Mounting position as required
Approvals EIB / KNX
CE mark in accordance with the EMC guideline and low
voltage guideline
Device Technology
Analogue Actuator Module AAM/S 4.1
2CDC 071 157 F0006

7
ABB i-bus®EIB / KNX
Fig. 5: Circuit diagram AAM/S 4.1
1Connection to analogue actuator 4 Connection terminals A5…A8
2Status LED output A5…A8 5Connection terminal 24 V AC
3Status LED device
3.1.1 Circuit diagram
Device Technology
Analogue Actuator Module AAM/S 4.1

8
ABB i-bus®EIB / KNX
Fig. 6: Analogue Actuator Module AAM/S 4.1
The connection to the Analogue Actuator will by carried out via a 6-pole
system connector (supplied with the Analogue Actuator Module).
A maximum of one Analogue Actuator Module can be connected.
An Analogue Actuator Module can be replaced while the system is in opera-
tion (disconnect voltage supply from module!). After the replacement, the
Analogue Actuator makes a reset after approx. 25 s. This action reinitialises
all outputs of the Analogue Actuator and resets them to their original state.
Removal or addition of modules without adapting the project and
subsequent downloading into the Analogue Actuator is not permitted
as this will result in system malfunctions.
쐌
Do not connect electronic ballast’s or electronic transformers
with 1 – 10 V control input to the outputs!
쐌Do not connect external voltages to the outputs.
Connected components must ensure safe separation from
other voltages.
쐌The 0 V terminals must not be connected with the terminals
of the same designation of an Analogue Actuator (risk of
irreparable damage!).
쐌 The 0 V terminals of outputs A5...A8 are internally connected.
3.1.2 Dimension drawing
3.1.3 Installation
Device Technology
Analogue Actuator Module AAM/S 4.1