ABB SV/S 30.160.1.1 User manual

—
PRODUCT MANUAL
ABB i-bus® KNX
SV/S
KNX-Power Supplies

ABB i-bus®KNX
Contents
SV/S xx.xxx.x.1 | 2CDC501049D0201 Rev. A i
Contents
side
1General ................................................................................................. 3
1.1 Using the product manual.............................................................................................................3
1.1.1 Structure of the product manual ...................................................................................................4
1.1.2 Notes............................................................................................................................................4
1.2 Product and functional overview...................................................................................................5
1.2.1 Brief overview...............................................................................................................................5
2Device technology............................................................................... 7
2.1 Standard Power Supply, 640/320/160 mA, MDRC.......................................................................7
2.1.1 Technical data..............................................................................................................................7
2.1.2 Connection schematic..................................................................................................................9
2.1.3 Dimension drawing.....................................................................................................................10
2.1.4 Operating and display elements.................................................................................................11
2.1.5 Mounting and installation............................................................................................................11
2.2 KNX Power Supply with diagnostics, 640/320 mA, MDRC.........................................................12
2.2.1 Technical data............................................................................................................................12
2.2.2 Connection schematic................................................................................................................15
2.2.3 Dimension drawing.....................................................................................................................16
2.2.4 Operating and display elements.................................................................................................17
2.2.5 Mounting and installation............................................................................................................18
3Start-up............................................................................................... 19
3.1 Overview.....................................................................................................................................19
3.2 Conversion of previous application program versions................................................................20
3.2.1 Procedure...................................................................................................................................20
3.3 Parameters.................................................................................................................................21
3.3.1 Parameter window General........................................................................................................22
3.4 Communication objects..............................................................................................................24
3.4.1 Summary of communication objects...........................................................................................24
3.4.2 Communication objects, General................................................................................................25
4Planning and application .................................................................. 27
4.1 Additional voltage output............................................................................................................27
4.2 Reset..........................................................................................................................................28
4.3 Faults..........................................................................................................................................29
AAppendix ............................................................................................ 31
A.1 Ordering details..........................................................................................................................31

ABB i-bus®KNX
General
SV/S xx.xxx.x.1 | 2CDC501049D0201 Rev. A 3
1 General
KNX power supplies provide the system voltage (SELV) for KNX components. The choked output voltage
powers individual components and enables them to communicate.
1.1 Using the product manual
This manual provides detailed technical information about the power supplies and how to mount and
program them. Device application is explained using examples.
This manual is subdivided into the following sections:
Section 1 General
Section 2 Device technology
Section 3 Commissioning
Section 4 Planning and application
Section A Appendix

ABB i-bus®KNX
General
42CDC501049D0201 Rev. A | SV/S xx.xxx.x.1
1.1.1 Structure of the product manual
All parameters are initially described in chapter 3. Following the parameter descriptions are descriptions
for the communication objects.
Please note
The descriptions of parameters and communication objects in section 3 apply only to those power
supplies with diagnostics functions (SV/S 30.320.2.1 and SV/S 30.640.5.1).
1.1.2 Notes
Notes and safety instructions are represented as follows in this manual:
Please note
Tips for usage and operation
Examples
Application examples, installation examples, programming examples
Important
These safety instructions are used as soon as there is danger of a malfunction without risk of damage
or injury.
Caution
These safety instructions are used as soon as there is danger of a malfunction without risk of damage
or injury.
Danger
These safety instructions are used if there is a danger to life and limb with inappropriate use.
Danger
These safety instructions are used if there is an extreme danger to life with inappropriate use.

ABB i-bus®KNX
General
SV/S xx.xxx.x.1 | 2CDC501049D0201 Rev. A 5
1.2 Product and functional overview
ABB power supplies are designed to be fully compatible with each other. Devices with diagnostics or bus
functions for complex applications are available alongside standard devices. An uninterruptable battery
backed-up version is also available.
All KNX power supplies have an integrated choke. They connect to the ABB i-bus®KNX via a bus
connection terminal.
1.2.1 Brief overview
SV/S
30.160.1.1
SV/S
30.320.1.1
SV/S
30.640.3.1
SV/S
30.320.2.1
SV/S
30.640.5.1
SU/S
30.640.1**
Property
Standard
Diagnostics
Back-up
supply
Supply voltage (in V AC) 100 – 240 100 – 240 100 – 240 100 – 240 100 – 240 210 – 240
KNX rated voltage (in V DC)
30
30
30
30
30
30
KNX rated current (in mA) 160 320 640 320 640 640
Type of installation
MDRC
MDRC
MDRC
MDRC
MDRC
MDRC
Mounting width in space units
4
4
4
4
4
8
Integrated choke 





Short-circuit and overload
monitoring 





Mains failure back-up time
(in ms) 200 ms 200 ms 200 ms 200 ms 200 ms 200 ms
without
battery
Mains failure back-up time
If used with a
sealed lead-acid battery, e.g.
- AM/S 12.1
- SAK 7
- 2 x SAK 7 in parallel
- SAK 12
- 2 x SAK 12 in parallel
- SAK 17:
- 2 x SAK 17 in parallel
- - - - -
10 min.*
up to 2.5 h*
up to 5 h*
up to 5.5 h*
up to 11 h*
up to 8 h*
up to 16 h*
Output voltage without
choke (30 V DC) - - - -
Diagnostics or bus function - - - -
Output voltage indicator 
Overload Indicator 





Bus current indicator
-
-
-


-
Telegram traffic indicator - - - -
Communication error indicator
-
-
-


-
Bus reset button and indicator
-
-
-


-
Mains voltage OK indicator - - - - - 
Battery voltage OK indicator
-
-
-
-
-

Floating contact
for fault reporting - - - - - 
* Times based on a new battery at rated load
** see product manual 2CDC501002D0203

ABB i-bus®KNX
Device technology
SV/S xx.xxx.x.1 | 2CDC501049D0201 Rev. A 7
2 Device technology
2.1 Standard Power Supply, 640/320/160 mA, MDRC
KNX power supplies generate and
monitor the KNX system voltage (SELV).
The b
us line is decoupled from the power
supply by an
integrated choke.
The voltage output is short
-circuit and
overload protected
.
The two
-color LED indicates device
output status.
Device type SV/S 30.640.3.1 has an
additional 30 V DC short-circuit and
overload protected voltage output that
can be used to power an additional bus
line (in combination with a separate
choke).
2.1.1 Technical data
Supply
Supply voltage U
s
100 – 240 V AC, 50/60 Hz
(85…265 V AC)
Power consumption
- SV/S 30.160.1.1
- SV/S 30.320.1.1
- SV/S 30.640.3.1
Normal operation Maximum
6.6 W 21 W
12.5 W 30 W
24 W 55 W
Power loss
- SV/S 30.160.1.1
- SV/S 30.320.1.1
- SV/S 30.640.3.1
Normal operation Maximum
1.8 W 4.4 W
2.5 W 6 W
4 W 9 W
Outputs
KNX voltage output I1
Rated voltage UN
Minimum distance between 2 SV/S in one line
1 line with integrated choke
30 V DC +1/-2 V, SELV
200 m (KNX bus line)
Voltage output I
2
(SV/S 30.640.3.1 only)
Rated voltage UN
without choke
30 V DC +1/-1 V, SELV
The voltage output without choke may only be
used to power an additional bus line in
combination with a separate choke.
Current
- SV/S 30.160.1.1
- SV/S 30.320.1.1
- SV/S 30.640.3.1 (total current I1and I2)
Rated curr. Overload curr. Short-circuit curr.
INIOvl ISc
160 mA 0.3 A 0.5 A
320 mA 0.5 A 0.8 A
640 mA 0.9 A 1.4 A
Power failure buffering time
200 ms
Connections
KNX
Bus connection terminal
Mains voltage input Screw terminal
0.2…2.5 mm2fine-strand
0.2…4 mm2solid
Tightening torque
Maximum 0.6 Nm
Operating and display elements
LED status (two-colored green/red)
Green: I < I
Ovl
Red: overload.
Red, flashing: short-circuit
Degree of protection
IP 20
EN 60 529
2CDC 071 004 S0014

ABB i-bus®KNX
Device technology
82CDC501049D0201 Rev. A | SV/S xx.xxx.x.1
Protection class
II EN 61 140
Isolation category Overvoltage category
Pollution degree III under EN 60 664-1 2 under EN 60 664-1
Temperature range
Operation
Storage
Transport
-5 °C…+45 °C
-25…+55 °C
-25…+70 °C
Ambient conditions Maximum air humidity 93 %, no condensation allowed
Design
Modular installation device (MDRC)
Modular installation device, Pro M
Main dimensions (H x W x D)
90 x 72 x 64.5 mm
Mounting width
4 x 18 mm modules
Mounting depth
64.5 mm
Mounting
On 35 mm mounting rail
EN 60 715
Mounting position
As required
Weight Approx. 0.25 kg
Housing, color Plastic housing, gray
Approvals KNX under EN 50 090-1, -2
CE mark
In accordance with the EMC guideline and low
voltage guideline
Important
If the device overheats due to extended overload (> 100 °C in housing) it switches off automatically.
The LED is off. The device can be switched on again only after it has been disconnected from the mains
for 60 seconds and has cooled to operational temperature internally.
Eliminate the cause of the overload before switching back on.
When commissioning the device, ensure that the rated current is not continuously exceeded.
The voltage output without choke ( I2) is not electrically isolated from the KNX voltage output (I1). It may
only be used to power an additional bus line in combination with a separate choke. It may not,
for example, be used to power IP devices (see SELV guidelines).
Devices are designed for continuous operation. They are not approved for frequent switching on and off.

ABB i-bus®KNX
Device technology
SV/S xx.xxx.x.1 | 2CDC501049D0201 Rev. A 9
2.1.2 Connection schematic
1 Bus connection terminal
2 Label carrier
3 Power supply connection Us
4 Status LED
5 Voltage output without choke, I2 (SV/S 30.640.3.1 only)
2CDC072007F0013

ABB i-bus®KNX
Device technology
10 2CDC501049D0201 Rev. A | SV/S xx.xxx.x.1
2.1.3 Dimension drawing
2CDC072013F0013

ABB i-bus®KNX
Device technology
SV/S xx.xxx.x.1 | 2CDC501049D0201 Rev. A 11
2.1.4 Operating and display elements
Indicator Description Function
LED status
(green/red)
Two-colored indicator for displaying mains
voltage, overload and short-circuit. For
SV/S 30.640.3.1, overload and short-circuit
current values apply to the total current,
I = I1+ I2
Green: Device operating normally (I < IOvl)
Red: Overload (IOvl < I < ISc)
Red, flashing: Current limiting is active
Output voltage regulated downwards
(I = ISc)
OFF: Mains voltage absent
2.1.5 Mounting and installation
Accessibility to the device for the purpose of operation, testing, visual inspection, maintenance and repair
must be provided compliant to VDE 0100-520.
Mounting
Mounting and commissioning may only be carried out by electrical specialists. The appropriate standards,
directives, regulations and specifications should be observed when planning and setting up electrical
installations.
Protect the device from moisture, dirt and damage during transport, storage and operation.
Only operate the device within the specified technical data!
The device should only be operated in an enclosed housing (distribution board)!
Cleaning
If devices become dirty, they can be cleaned using a dry cloth. Should a dry cloth not remove the dirt, they
can be cleaned using a slightly moistened cloth and soap solution. Corrosive agents or solutions should
never be used.
Maintenance
The device is maintenance-free. No repairs should be carried out by unauthorized personnel if damage
occurs, e.g. during transport and/or storage. The warranty expires if the device is opened.

ABB i-busKNX
Device technology
12 2CDC501049D0201 Rev. A | SV/S xx.xxx.x.1
2.2 KNX Power Supply with diagnostics, 640/320 mA, MDRC
KNX power supplies generate and
monitor the KNX system voltage (SELV).
The bus line is decoup
led from the power
supply by an
integrated choke.
Bus current, bus voltage, overload and
other messages can be sent via KNX for
monitoring and diagnostic purposes.
The voltage output is short
-circuit and
overload protected
.
The LEDs indicate the bus current
consumption and the status of the line or
device.
Device type SV/S 30.640.5.1 has an
additional 30 V DC short-circuit and
overload protected voltage output that
can be used to power an additional bus
line (in combination with a separate
choke).
2.2.1 Technical data
Supply
Supply voltage U
s
100 – 240 V AC, 50/60 Hz
(85…265 V AC)
Power consumption
- SV/S 30.320.2.1
- SV/S 30.640.5.1
Normal operation Maximum
12.5 W 30 W
24 W 55 W
Power loss
- SV/S 30.320.2.1
- SV/S 30.640.5.1
Normal operation Maximum
2.5 W 6 W
4 W 9 W
Outputs
KNX voltage output I
1
Rated voltage UN
Minimum distance between 2 SV/S in one line
1 line with integrated choke
30 V DC +1/-2 V, SELV
200 m (KNX bus line)
Voltage output I2(SV/S 30.640.5.1 only)
Rated voltage UNwithout choke 30 V DC +1/-1 V, SELV
The voltage output without choke may only be
used to power an additional bus line in
combination with a separate choke.
Current
- SV/S 30.320.2.1
- SV/S 30.640.5.1 (total current I1and I2)
Rated curr. Overload curr. Short-circuit curr.
INIOvl ISc
320 mA 0.5 A 0.8 A
640 mA 0.9 A 1.4 A
Power failure buffering time
200 ms
Connections
KNX
Bus connection terminal
Mains voltage input
Screw terminal
0.2…2.5 mm2fine-strand
0.2…4 mm2solid
Tightening torque Maximum 0.6 Nm
2CDC071017S0013

ABB i-busKNX
Device technology
SV/S xx.xxx.x.1 | 2CDC501049D0201 Rev. A 13
Operating and display elements Programming button and LED (red) For assignment of the physical address
U
N
OK LED (green)
ON: Bus voltage and mains voltage OK
LED I > I
max
(red)
ON: Short-circuit or overload
Bus current LEDs (7 x yellow)
ON: Indicates present bus current
Telegr. LED (yellow)
ON: Telegram traffic
Comm. error LED (yellow) ON: Communication error on bus
Reset button and LED (red) ON: Line reset.
To reset the device, press the button until the
LED comes on. The line is disconnected from
the voltage supply for 20 seconds. The LED then
goes off again.
OFF: Reset is complete.
Degree of protection IP 20 EN 60 529
Protection class
II
EN 61 140
Isolation category
Overvoltage category
Pollution degree
III under EN 60 664-1
2 under EN 60 664-1
Temperature range Operation
Storage
Transport
-5 °C…+45 °C
-25…+55 °C
-25…+70 °C
Ambient conditions
Maximum air humidity
93 %, no condensation allowed
Design
Modular installation device (MDRC)
Modular installation device, Pro
M
Main dimensions (H x W x D) 90 x 72 x 64.5 mm
Mounting width 4 x 18 mm modules
Mounting depth 64.5 mm
Mounting On 35 mm mounting rail EN 60 715
Mounting position
As required
Weight
Approx. 0.26 kg
Housing, color
Plastic housing, gray
Approvals
KNX under EN 50 090-1, -2
CE mark
In accordance with the EMC guideline and low
voltage guideline
Device type
Application
Maximum number of
communication objects
Maximum number of
group addresses
Maximum number
of associations
SV/S 30.320.2.1
SV/S 30.640.5.1
Power Supply, Diagnosis, 320mA/...*
Power Supply, Diagnosis, 640mA/...*
7
9
254
254
254
254
* … = current version number of the application

ABB i-busKNX
Device technology
14 2CDC501049D0201 Rev. A | SV/S xx.xxx.x.1
Please note
ETS and the current version of the device application are required for programming.
The current version of the application is available for download at www.abb.com/knx. After import it is
available in ETS under ABB/System devices/Power Supplies.
The device does not support the password function of the KNX device in ETS. If you inhibit access to all
the project devices using a BCU code, it has no effect on this device. Data can still be read and
programmed.
Important
If the device overheats due to extended overload (> 100 °C in housing) it switches off automatically.
All LEDs are OFF. The device can be switched on again only after it has been disconnected from the
mains for 60 seconds and has cooled to operational temperature internally.
Eliminate the cause of the overload before switching back on.
When commissioning the device, ensure that the rated current is not continuously exceeded.
The voltage output without choke ( I2) is not electrically isolated from the KNX voltage output (I1). It may
only be used to power an additional bus line in combination with a separate choke. It may not, for
example, be used to power IP devices.
Devices are designed for continuous operation. They are not approved for frequent switching on and off.

ABB i-busKNX
Device technology
SV/S xx.xxx.x.1 | 2CDC501049D0201 Rev. A 15
2.2.2 Connection schematic
1 Bus connection terminal
2 Programming button and LED (red)
3 Label carrier
4 Reset button and LED (red)
5 Comm. error LED (yellow)
6 Telegr. LED (yellow)
7 Power supply connection Us
8 UNOK LED (green)
9 I > Imax LED (red)
10 Bus current LED (7 x yellow)
11 Voltage output without choke, I2 (SV/S 30.640.5.1 only)
2CDC072001F0013

ABB i-busKNX
Device technology
16 2CDC501049D0201 Rev. A | SV/S xx.xxx.x.1
2.2.3 Dimension drawing
2CDC072004F0013

ABB i-busKNX
Device technology
SV/S xx.xxx.x.1 | 2CDC501049D0201 Rev. A 17
2.2.4 Operating and display elements
Operation/
Indicator light
Description
Function
LED green
Indicates status of mains and output
voltage
The LED is off during programming.
ON: Mains voltage present, device operating normally
(I < IOvl)
OFF: Mains voltage absent
LED red
Indicates overload/short-circuit current.
The LED lights up when the output
current exceeds the overload limit
(I > IOvl). For SV/S 30.640.5.1, overload
and short-circuit current values apply to
the total current, I = I1+ I2
SV/S 30.320.2.1 SV/S 30.640.5.1
ON (I > I
Ovl
)
I > 500 mA I > 900 mA
7 LEDs (yellow)
LED No.:
7.
6.
5.
4.
3.
2.
1.
Indicates present bus current
If a current value exceeds/falls below
the indicator value by +/- 5 % for at
least 110 ms, the LED comes ON/goes
OFF.
Example, SV/S 30.640.5.1:
LED No. 2 (200 mA) lights up if the
output current exceeds/stays at
210 mA for 110 ms. The LED goes off
if the current falls below 190 mA for at
least 110 ms.
LED
No.:
SV/S 30.320.2.1
SV/S 30.640.5.1
Indicator value
[mA] Indicator value [mA]
7.
350
700
6.
300
600
5. 250 550
4. 200 400
3. 150 300
2.
100
200
1.
50
100
Triggers and indicates a bus reset.
This function can be triggered only
when mains voltage is applied.
Operating one line with two power
supplies:
when the mains supply fails, the Reset
button on the affected device does not
function.
Reset button:Pressing the button for > 2 seconds triggers a
reset. The line shorts. Pressing the button again
during a reset has no effect (no reaction, no
retrigger, no interrupt, etc.)
ON: After pressing for > 2 secs. or for the duration of
the reset (20 s) after receiving the object value.
ON: After 20 s reset
Flashes: At 4.8 Hz while being pressed
Indicates a KNX telegram AN: Receiving telegram
OFF: Stand-by mode
Indicates a communication error on the
bus
ON: The LED comes ON for 1 second and is
retriggerable if there is a transmission error or if a
telegram fails or is incomplete (e.g. “BUSY”,
“NAK” (receipt not correct)).
OFF: Device working normally
Please note
Individual LEDs may flash during downloads or while the application is being unloaded.

ABB i-busKNX
Device technology
18 2CDC501049D0201 Rev. A | SV/S xx.xxx.x.1
2.2.5 Mounting and installation
Accessibility to the device for the purpose of operation, testing, visual inspection, maintenance and repair
must be provided compliant to VDE 0100-520.
Commissioning requirements
To commission the device you will need a PC with ETS, a connection to the ABB i-bus®,
e.g. via a KNX interface, and a supply voltage of 110/230 V.
Mounting
Mounting and commissioning may only be carried out by electrical specialists. The appropriate standards,
directives, regulations and specifications should be observed when planning and setting up electrical
installations.
Protect the device from moisture, dirt and damage during transport, storage and operation.
Only operate the device within the specified technical data!
The device should only be operated in an enclosed housing (distribution board)!
Supplied state
The device is supplied with the physical address 15.15.255.
The application program is pre-installed. It is therefore only necessary to load group addresses and
parameters during commissioning.
However, the complete application program can be reloaded if required. Downloads may take longer after
a change of application program, an interrupted download or after unloading a device.
Assignment of the physical address
The assignment and programming of the physical address is carried out in ETS.
The device features a programming button for assignment of the physical device address. The red
Programming LED lights up after the button has been pushed. It goes off as soon as ETS has assigned
the physical address or the Programming button is pressed again.
Cleaning
If devices become dirty, they can be cleaned using a dry cloth. Should a dry cloth not remove the dirt, they
can be cleaned using a slightly moistened cloth and soap solution. Corrosive agents or solutions should
never be used.
Maintenance
The device is maintenance-free. No repairs should be carried out by unauthorized personnel if damage
occurs, e.g. during transport and/or storage. The warranty expires if the device is opened.