ABB RELION 650 SERIES Quick start guide

—
RELION® 650 SERIES
Transformer protection RET650
Version 2.1
Commissioning manual

Document ID: 1MRK 504 160-UEN
Issued: March 2019
Revision: A
Product version: 2.1
© Copyright 2016 ABB. All rights reserved

Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third party, nor
used for any unauthorized purpose.
The software and hardware described in this document is furnished under a license and may
be used or disclosed only in accordance with the terms of such license.
This product includes software developed by the OpenSSL Project for use in the OpenSSL
Toolkit. (http://www.openssl.org/) This product includes cryptographic software written/
developed by: Eric Young ([email protected]) and Tim Hudson ([email protected]).
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or product names
mentioned in this document may be trademarks or registered trademarks of their respective
holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.

Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or product
description and are not to be deemed as a statement of guaranteed properties. All persons
responsible for applying the equipment addressed in this manual must satisfy themselves that
each intended application is suitable and acceptable, including that any applicable safety or
other operational requirements are complied with. In particular, any risks in applications where
a system failure and/or product failure would create a risk for harm to property or persons
(including but not limited to personal injuries or death) shall be the sole responsibility of the
person or entity applying the equipment, and those so responsible are hereby requested to
ensure that all measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be completely ruled
out. In case any errors are detected, the reader is kindly requested to notify the manufacturer.
Other than under explicit contractual commitments, in no event shall ABB be responsible or
liable for any loss or damage resulting from the use of this manual or the application of the
equipment.

Conformity
This product complies with the directive of the Council of the European Communities on the
approximation of the laws of the Member States relating to electromagnetic compatibility
(EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified
voltage limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests
conducted by ABB in accordance with the product standard EN 60255-26 for the EMC directive,
and with the product standards EN 60255-1 and EN 60255-27 for the low voltage directive. The
product is designed in accordance with the international standards of the IEC 60255 series.

Table of contents
Section 1 Introduction.........................................................................................................7
1.1 This manual......................................................................................................................................... 7
1.2 Intended audience..............................................................................................................................7
1.3 Product documentation................................................................................................................... 8
1.3.1 Product documentation set........................................................................................................ 8
1.3.2 Document revision history...........................................................................................................9
1.3.3 Related documents....................................................................................................................... 9
1.4 Document symbols and conventions...........................................................................................10
1.4.1 Symbols......................................................................................................................................... 10
1.4.2 Document conventions............................................................................................................... 11
1.5 IEC 61850 edition 1 / edition 2 mapping......................................................................................11
Section 2 Safety information........................................................................................... 15
2.1 Symbols on the product..................................................................................................................15
2.2 Warnings............................................................................................................................................ 15
2.3 Caution signs.................................................................................................................................... 16
2.4 Note signs.......................................................................................................................................... 17
Section 3 Available functions........................................................................................... 19
3.1 Main protection functions..............................................................................................................19
3.2 Back-up protection functions........................................................................................................19
3.3 Control and monitoring functions............................................................................................... 20
3.4 Communication................................................................................................................................ 22
3.5 Basic IED functions.......................................................................................................................... 23
Section 4 Starting up.........................................................................................................25
4.1 Factory and site acceptance testing............................................................................................25
4.2 Commissioning checklist............................................................................................................... 25
4.3 Checking the power supply............................................................................................................26
4.4 Energizing the IED............................................................................................................................26
4.4.1 Checking the IED operation.......................................................................................................26
4.4.2 IED start-up sequence................................................................................................................ 26
4.5 Setting up communication between PCM600 and the IED..................................................... 27
4.6 Writing an application configuration to the IED........................................................................32
4.7 Checking CT circuits........................................................................................................................ 32
4.8 Checking VT circuits........................................................................................................................ 33
4.9 Using the RTXP test switch............................................................................................................33
4.10 Checking the binary input/output circuits.................................................................................34
4.10.1 Binary input circuits.................................................................................................................... 34
4.10.2 Binary output circuits................................................................................................................. 34
4.11 Checking optical connections....................................................................................................... 34
Table of contents
1
Commissioning manual

Section 5 Configuring the IED and changing settings.................................................. 35
5.1 Overview............................................................................................................................................ 35
5.2 Configuring analog CT inputs....................................................................................................... 35
5.3 Supervision of input/output modules.........................................................................................36
Section 6 Establishing connection and verifying the SPA/IEC communication........ 37
6.1 Entering settings..............................................................................................................................37
6.1.1 Entering SPA settings................................................................................................................. 37
6.1.2 Entering IEC settings.................................................................................................................. 37
6.2 Verifying the communication........................................................................................................ 38
6.2.1 Verifying SPA communication.................................................................................................. 38
6.2.2 Verifying IEC communication....................................................................................................38
6.3 Fibre optic loop................................................................................................................................ 38
6.4 Optical budget calculation for serial communication with SPA/IEC ................................... 39
Section 7 Establishing connection and verifying the LON communication............... 41
7.1 Communication via the rear ports ...............................................................................................41
7.1.1 LON communication................................................................................................................... 41
7.1.2 The LON Protocol........................................................................................................................ 42
7.1.3 Hardware and software modules.............................................................................................42
7.2 Optical budget calculation for serial communication with LON ...........................................44
Section 8 Establishing connection and verifying the IEC 61850 communication.....45
8.1 Overview............................................................................................................................................ 45
8.2 Setting the station communication.............................................................................................45
8.3 Verifying the communication........................................................................................................45
Section 9 Testing IED operation...................................................................................... 47
9.1 Preparing for test.............................................................................................................................47
9.1.1 Requirements............................................................................................................................... 47
9.1.2 Preparing the IED to verify settings........................................................................................ 48
9.2 Activating the test mode............................................................................................................... 49
9.3 Preparing the connection to the test equipment..................................................................... 49
9.4 Connecting the test equipment to the IED................................................................................ 50
9.5 Releasing the function to be tested............................................................................................ 50
9.6 Verifying analog primary and secondary measurement.......................................................... 51
9.7 Testing the protection functionality............................................................................................51
9.8 Forcing of binary input/output signals for testing.................................................................. 52
9.8.1 Forcing concept........................................................................................................................... 52
9.8.2 How to enable forcing................................................................................................................ 52
9.8.2.1 Enable forcing by using LHMI................................................................................................ 52
9.8.2.2 Enable forcing using TESTMODE function block...............................................................52
9.8.3 How to change binary input/output signals using forcing................................................ 53
9.8.3.1 Forcing by using LHMI.............................................................................................................53
9.8.3.2 Forcing by using PCM600...................................................................................................... 54
9.8.4 How to undo forcing changes and return the IED to normal operation.......................... 56
9.8.4.1 Undo forcing by using TESTMODE component.................................................................56
Table of contents
2
Commissioning manual

9.8.4.2 Undo forcing by using LHMI.................................................................................................. 56
9.8.4.3 Undo forcing by using PCM600............................................................................................ 56
Section 10 Testing functionality by secondary injection............................................... 59
10.1 Testing disturbance report............................................................................................................59
10.1.1 Introduction..................................................................................................................................59
10.1.2 Disturbance report settings......................................................................................................59
10.1.3 Disturbance recorder (DR).........................................................................................................59
10.1.4 Event recorder (ER) and Event list (EL)...................................................................................60
10.2 Identifying the function to test in the technical reference manual ......................................60
10.3 Differential protection....................................................................................................................60
10.3.1 Transformer differential protection T3WPDIF...................................................................... 60
10.3.1.1 Verifying the settings.............................................................................................................. 61
10.3.1.2 Completing the test.................................................................................................................61
10.3.2 High impedance differential protection HZPDIF ................................................................. 61
10.3.2.1 Verifying the settings.............................................................................................................. 61
10.3.2.2 Completing the test.................................................................................................................62
10.3.3 Restricted earth-fault protection, low impedance REFPDIF ..............................................62
10.3.3.1 Verifying the settings..............................................................................................................62
10.3.3.2 Completing the test.................................................................................................................63
10.4 Current protection...........................................................................................................................63
10.4.1 Instantaneous phase overcurrent protection 3-phase output PHPIOC .......................... 63
10.4.1.1 Measuring the operate limit of set values.......................................................................... 63
10.4.1.2 Completing the test................................................................................................................ 64
10.4.2 Four step phase overcurrent protection 3-phase output OC4PTOC................................64
10.4.2.1 Verifying the settings..............................................................................................................64
10.4.2.2 Completing the test................................................................................................................ 65
10.4.3 Instantaneous residual overcurrent protection EFPIOC .................................................... 65
10.4.3.1 Measuring the operate limit of set values.......................................................................... 65
10.4.3.2 Completing the test................................................................................................................ 65
10.4.4 Four step residual overcurrent protection, (Zero sequence or negative sequence
directionality) EF4PTOC ............................................................................................................65
10.4.4.1 Four step directional earth fault protection...................................................................... 66
10.4.4.2 Four step non-directional earth fault protection..............................................................66
10.4.4.3 Completing the test................................................................................................................ 66
10.4.5 Thermal overload protection, one time constant, Celsius/Fahrenheit
LCPTTR/LFPTTR.......................................................................................................................... 66
10.4.5.1 Measuring the operate and time limit of set values......................................................... 66
10.4.5.2 Completing the test.................................................................................................................67
10.4.6 Thermal overload protection, two time constants TRPTTR ...............................................67
10.4.6.1 Checking operate and reset values...................................................................................... 67
10.4.6.2 Completing the test................................................................................................................ 68
10.4.7 Breaker failure protection, phase segregated activation and output CCRBRF..............68
10.4.7.1 Checking the phase current operate value, IP> ................................................................. 68
10.4.7.2 Checking the residual (earth fault) current operate value IN> set below IP> ..............68
10.4.7.3 Checking the re-trip and back-up times..............................................................................68
10.4.7.4 Verifying the re-trip mode......................................................................................................69
Table of contents
3
Commissioning manual

10.4.7.5 Verifying the back-up trip mode...........................................................................................69
10.4.7.6 Verifying instantaneous back-up trip at CB faulty condition......................................... 70
10.4.7.7 Verifying the case RetripMode = Contact ........................................................................... 70
10.4.7.8 Verifying the function mode Current&Contact .................................................................. 71
10.4.7.9 Completing the test................................................................................................................. 71
10.4.8 Pole discordance protection CCPDSC..................................................................................... 71
10.4.8.1 Verifying the settings.............................................................................................................. 71
10.4.8.2 Completing the test.................................................................................................................72
10.5 Voltage protection...........................................................................................................................72
10.5.1 Two step undervoltage protection UV2PTUV ....................................................................... 72
10.5.1.1 Verifying the settings.............................................................................................................. 72
10.5.1.2 Completing the test.................................................................................................................73
10.5.2 Two step overvoltage protection OV2PTOV ......................................................................... 74
10.5.2.1 Verifying the settings.............................................................................................................. 74
10.5.2.2 Extended testing...................................................................................................................... 74
10.5.2.3 Completing the test.................................................................................................................74
10.5.3 Two step residual overvoltage protection ROV2PTOV ....................................................... 74
10.5.3.1 Verifying the settings.............................................................................................................. 75
10.5.3.2 Completing the test.................................................................................................................75
10.5.4 Loss of voltage check LOVPTUV .............................................................................................. 75
10.5.4.1 Measuring the operate limit of set values...........................................................................75
10.5.4.2 Completing the test.................................................................................................................76
10.6 Multipurpose protection................................................................................................................ 76
10.6.1 General current and voltage protection CVGAPC................................................................. 76
10.6.1.1 Built-in overcurrent feature (non-directional)....................................................................76
10.6.1.2 Overcurrent feature with current restraint......................................................................... 77
10.6.1.3 Overcurrent feature with voltage restraint.........................................................................77
10.6.1.4 Overcurrent feature with directionality...............................................................................78
10.6.1.5 Over/Undervoltage feature....................................................................................................78
10.6.1.6 Completing the test.................................................................................................................78
10.7 Secondary system supervision......................................................................................................78
10.7.1 Fuse failure supervision FUFSPVC........................................................................................... 78
10.7.1.1 Checking that the binary inputs and outputs operate as expected ............................. 79
10.7.1.2 Measuring the operate value for the negative sequence function ............................... 79
10.7.1.3 Measuring the operate value for the zero-sequence function ...................................... 80
10.7.1.4 Measuring the operate value for the dead line detection function................................81
10.7.1.5 Checking the operation of the du/dt and di/dt based function ................................... 81
10.7.1.6 Completing the test.................................................................................................................82
10.8 Control............................................................................................................................................... 82
10.8.1 Synchrocheck, energizing check, and synchronizing SESRSYN......................................... 82
10.8.1.1 Testing the synchronizing function......................................................................................83
10.8.1.2 Testing the synchrocheck check...........................................................................................84
10.8.1.3 Testing the energizing check.................................................................................................85
10.8.1.4 Testing the voltage selection................................................................................................ 87
10.8.1.5 Completing the test.................................................................................................................87
10.8.2 Apparatus control APC............................................................................................................... 87
Table of contents
4
Commissioning manual

10.8.3 Single command, 16 signals SINGLECMD............................................................................... 87
10.9 Logic...................................................................................................................................................88
10.9.1 Tripping logic, common 3-phase output SMPPTRC ............................................................ 88
10.9.1.1 Three-phase operating mode................................................................................................88
10.9.1.2 1ph/3ph operating mode....................................................................................................... 88
10.9.1.3 1ph/2ph/3ph operating mode.............................................................................................. 89
10.9.1.4 Circuit breaker lockout........................................................................................................... 90
10.9.1.5 Completing the test................................................................................................................ 90
10.10 Monitoring........................................................................................................................................ 90
10.10.1 Gas medium supervision SSIMG.............................................................................................. 90
10.10.1.1 Testing the liquid medium supervision for alarm and lock out conditions..................91
10.10.1.2 Completing the test.................................................................................................................91
10.10.2 Liquid medium supervision SSIML........................................................................................... 91
10.10.2.1 Testing the liquid medium supervision for alarm and lock out conditions..................91
10.10.2.2 Completing the test.................................................................................................................91
10.10.3 Breaker monitoring SSCBR........................................................................................................92
10.10.3.1 Verifying the settings..............................................................................................................92
10.10.3.2 Completing the test.................................................................................................................93
10.10.4 Event function EVENT.................................................................................................................93
10.10.5 Limit counter L4UFCNT..............................................................................................................93
10.10.5.1 Completing the test................................................................................................................ 94
10.11 Metering............................................................................................................................................ 94
10.11.1 Pulse-counter logic PCFCNT..................................................................................................... 94
10.11.2 Function for energy calculation and demand handling ETPMMTR................................... 94
10.11.2.1 Verifying the settings..............................................................................................................94
10.11.2.2 Completing the test................................................................................................................ 95
10.12 Station communication..................................................................................................................95
10.12.1 Multiple command and transmit MULTICMDRCV / MULTICMDSND................................ 95
10.13 Basic IED functions..........................................................................................................................96
10.13.1 Parameter setting group handling SETGRPS........................................................................ 96
10.13.1.1 Verifying the settings..............................................................................................................96
10.13.1.2 Completing the test................................................................................................................ 96
10.14 Exit test mode.................................................................................................................................. 96
Section 11 Checking the directionality............................................................................. 97
11.1 Overview............................................................................................................................................ 97
11.2 Testing the directionality of the distance protection.............................................................. 97
Section 12 Commissioning and maintenance of the fault clearing system.................99
12.1 Commissioning tests......................................................................................................................99
12.2 Periodic maintenance tests...........................................................................................................99
12.2.1 Visual inspection....................................................................................................................... 100
12.2.2 Maintenance tests.....................................................................................................................100
12.2.2.1 Preparation............................................................................................................................. 100
12.2.2.2 Recording................................................................................................................................ 100
12.2.2.3 Secondary injection............................................................................................................... 100
12.2.2.4 Alarm test.................................................................................................................................101
Table of contents
5
Commissioning manual

12.2.2.5 Self supervision check........................................................................................................... 101
12.2.2.6 Trip circuit check.................................................................................................................... 101
12.2.2.7 Measurement of service currents........................................................................................101
12.2.2.8 Restoring..................................................................................................................................102
Section 13 Troubleshooting............................................................................................. 103
13.1 Checking the self supervision signals........................................................................................103
13.1.1 Checking the self supervision function.................................................................................103
13.1.1.1 Determine the cause of an internal failure........................................................................103
13.1.2 Self supervision HMI data........................................................................................................ 103
13.1.2.1 General IED status..................................................................................................................103
13.2 Fault tracing....................................................................................................................................104
13.2.1 Internal fault indications..........................................................................................................104
13.2.2 Using front-connected PC....................................................................................................... 105
13.2.3 Diagnosing the IED status via the LHMI hint menu............................................................106
13.2.4 Hardware re-configuration......................................................................................................107
13.3 Repair instruction.......................................................................................................................... 108
13.4 Repair support................................................................................................................................109
13.5 Maintenance................................................................................................................................... 109
Section 14 Glossary............................................................................................................ 111
Table of contents
6
Commissioning manual

Section 1 Introduction
1.1 This manual
GUID-AB423A30-13C2-46AF-B7FE-A73BB425EB5F v19
The commissioning manual contains instructions on how to commission the IED. The manual
can also be used by system engineers and maintenance personnel for assistance during the
testing phase. The manual provides procedures for the checking of external circuitry and
energizing the IED, parameter setting and configuration as well as verifying settings by
secondary injection. The manual describes the process of testing an IED in a station which is
not in service. The chapters are organized in the chronological order in which the IED should be
commissioned. The relevant procedures may be followed also during the service and
maintenance activities.
1.2 Intended audience
GUID-C9B8127F-5748-4BEA-9E4F-CC762FE28A3A v10
This manual addresses the personnel responsible for commissioning, maintenance and taking
the IED in and out of normal service.
The commissioning personnel must have a basic knowledge of handling electronic equipment.
The commissioning and maintenance personnel must be well experienced in using protection
equipment, test equipment, protection functions and the configured functional logics in the
IED.
1MRK 504 160-UEN A Section 1
Introduction
7
Commissioning manual

1.3 Product documentation
1.3.1 Product documentation set GUID-3AA69EA6-F1D8-47C6-A8E6-562F29C67172 v15
IEC07000220-4-en.vsd
Planning & purchase Engineering Installing Commissioning Operation Maintenance Decommissioning Deinstalling & disposal
Application manual
Operation manual
Installation manual
Engineering manual
Communication
protocol manual
Cyber security
deployment guideline
Technical manual
Commissioning manual
IEC07000220 V4 EN-US
Figure 1: The intended use of manuals throughout the product lifecycle
The engineering manual contains instructions on how to engineer the IEDs using the various
tools available within the PCM600 software. The manual provides instructions on how to set
up a PCM600 project and insert IEDs to the project structure. The manual also recommends a
sequence for the engineering of protection and control functions, LHMI functions as well as
communication engineering for IEC 60870-5-103, IEC 61850, DNP3, LON and SPA.
The installation manual contains instructions on how to install the IED. The manual provides
procedures for mechanical and electrical installation. The chapters are organized in the
chronological order in which the IED should be installed.
The commissioning manual contains instructions on how to commission the IED. The manual
can also be used by system engineers and maintenance personnel for assistance during the
testing phase. The manual provides procedures for the checking of external circuitry and
energizing the IED, parameter setting and configuration as well as verifying settings by
secondary injection. The manual describes the process of testing an IED in a station which is
not in service. The chapters are organized in the chronological order in which the IED should be
commissioned. The relevant procedures may be followed also during the service and
maintenance activities.
The operation manual contains instructions on how to operate the IED once it has been
commissioned. The manual provides instructions for the monitoring, controlling and setting of
the IED. The manual also describes how to identify disturbances and how to view calculated
and measured power grid data to determine the cause of a fault.
Section 1 1MRK 504 160-UEN A
Introduction
8
Commissioning manual

The application manual contains application descriptions and setting guidelines sorted per
function. The manual can be used to find out when and for what purpose a typical protection
function can be used. The manual can also provide assistance for calculating settings.
The technical manual contains operation principle descriptions, and lists function blocks, logic
diagrams, input and output signals, setting parameters and technical data, sorted per
function. The manual can be used as a technical reference during the engineering phase,
installation and commissioning phase, and during normal service.
The communication protocol manual describes the communication protocols supported by
the IED. The manual concentrates on the vendor-specific implementations.
The point list manual describes the outlook and properties of the data points specific to the
IED. The manual should be used in conjunction with the corresponding communication
protocol manual.
The cyber security deployment guideline describes the process for handling cyber security
when communicating with the IED. Certification, Authorization with role based access control,
and product engineering for cyber security related events are described and sorted by
function. The guideline can be used as a technical reference during the engineering phase,
installation and commissioning phase, and during normal service.
1.3.2 Document revision history GUID-C8027F8A-D3CB-41C1-B078-F9E59BB73A6C v2.1.1
Document revision/date History
January 2016 First Release
March 2019 Maintenance Release
1.3.3 Related documents GUID-94E8A5CA-BE1B-45AF-81E7-5A41D34EE112 v4
Documents related to RET650 Document numbers
Application manual 1MRK 504 158-UEN
Commissioning manual 1MRK 504 160-UEN
Product guide 1MRK 504 161-BEN
Technical manual 1MRK 504 159-UEN
Type test certificate 1MRK 504 161-TEN
650 series manuals Document numbers
Operation manual 1MRK 500 125-UEN
Engineering manual 1MRK 511 381-UEN
Installation manual 1MRK 514 025-UEN
Communication protocol manual, DNP3 1MRK 511 374-UUS
Communication protocol manual, IEC 60870-5-103 1MRK 511 377-UEN
Communication protocol manual, IEC 61850 Edition 1 1MRK 511 375-UEN
Communication protocol manual, IEC 61850 Edition 2 1MRK 511 376-UEN
Communication protocol manual, LON 1MRK 511 378-UEN
Communication protocol manual, SPA 1MRK 511 379-UEN
Point list manual, DNP3 1MRK 511 380-UUS
Table continues on next page
1MRK 504 160-UEN A Section 1
Introduction
9
Commissioning manual

650 series manuals Document numbers
Accessories guide IEC: 1MRK 514 012-UEN
ANSI: 1MRK 514 012-UUS
Cyber security deployment guideline 1MRK 511 382-UEN
Connection and Installation components 1MRK 513 003-BEN
Test system, COMBITEST 1MRK 512 001-BEN
1.4 Document symbols and conventions
1.4.1 Symbols GUID-2945B229-DAB0-4F15-8A0E-B9CF0C2C7B15 v12
The electrical warning icon indicates the presence of a hazard which could
result in electrical shock.
The warning icon indicates the presence of a hazard which could result in
personal injury.
The caution hot surface icon indicates important information or warning about
the temperature of product surfaces.
Class 1 Laser product. Take adequate measures to protect the eyes and do not
view directly with optical instruments.
The caution icon indicates important information or warning related to the
concept discussed in the text. It might indicate the presence of a hazard which
could result in corruption of software or damage to equipment or property.
The information icon alerts the reader of important facts and conditions.
The tip icon indicates advice on, for example, how to design your project or
how to use a certain function.
Although warning hazards are related to personal injury, it is necessary to understand that
under certain operational conditions, operation of damaged equipment may result in
degraded process performance leading to personal injury or death. It is important that the
user fully complies with all warning and cautionary notices.
Section 1 1MRK 504 160-UEN A
Introduction
10
Commissioning manual

1.4.2 Document conventions GUID-96DFAB1A-98FE-4B26-8E90-F7CEB14B1AB6 v8
• Abbreviations and acronyms in this manual are spelled out in the glossary. The glossary
also contains definitions of important terms.
• Push button navigation in the LHMI menu structure is presented by using the push button
icons.
For example, to navigate between the options, use and .
• HMI menu paths are presented in bold.
For example, select Main menu/Settings.
• LHMI messages are shown in Courier font.
For example, to save the changes in non-volatile memory, select Yes and press .
• Parameter names are shown in italics.
For example, the function can be enabled and disabled with the
Operation setting.
• Each function block symbol shows the available input/output signal.
• the character ^ in front of an input/output signal name indicates that the signal
name may be customized using the PCM600 software.
• the character * after an input signal name indicates that the signal must be
connected to another function block in the application configuration to achieve a
valid application configuration.
• Dimensions are provided both in inches and millimeters. If it is not specifically mentioned
then the dimension is in millimeters.
1.5 IEC 61850 edition 1 / edition 2 mapping
GUID-C5133366-7260-4C47-A975-7DBAB3A33A96 v3
Table 1: IEC 61850 edition 1 / edition 2 mapping
Function block name Edition 1 logical nodes Edition 2 logical nodes
AGSAL AGSAL
SECLLN0
AGSAL
ALMCALH ALMCALH ALMCALH
ALTIM - ALTIM
ALTMS - ALTMS
ALTRK - ALTRK
BRCPTOC BRCPTOC BRCPTOC
BTIGAPC B16IFCVI BTIGAPC
CCPDSC CCRPLD CCPDSC
CCRBRF CCRBRF CCRBRF
CCSSPVC CCSRDIF CCSSPVC
CMMXU CMMXU CMMXU
CMSQI CMSQI CMSQI
CVGAPC GF2LLN0
GF2MMXN
GF2PHAR
GF2PTOV
GF2PTUC
GF2PTUV
GF2PVOC
PH1PTRC
GF2MMXN
GF2PHAR
GF2PTOV
GF2PTUC
GF2PTUV
GF2PVOC
PH1PTRC
CVMMXN CVMMXN CVMMXN
DPGAPC DPGGIO DPGAPC
DRPRDRE DRPRDRE DRPRDRE
Table continues on next page
1MRK 504 160-UEN A Section 1
Introduction
11
Commissioning manual

Function block name Edition 1 logical nodes Edition 2 logical nodes
EF4PTOC EF4LLN0
EF4PTRC
EF4RDIR
GEN4PHAR
PH1PTOC
EF4PTRC
EF4RDIR
GEN4PHAR
PH1PTOC
EFPIOC EFPIOC EFPIOC
ETPMMTR ETPMMTR ETPMMTR
FUFSPVC SDDRFUF FUFSPVC
HZPDIF HZPDIF HZPDIF
INDCALH INDCALH INDCALH
ITBGAPC IB16FCVB ITBGAPC
L4UFCNT L4UFCNT L4UFCNT
LCPTTR LCPTTR LCPTTR
LD0LLN0 LLN0 LLN0
LDLPSCH LDLPDIF LDLPSCH
LFPTTR LFPTTR LFPTTR
LMBRFLO LMBRFLO LMBRFLO
LOVPTUV LOVPTUV LOVPTUV
LPHD LPHD LPHD
LT3CPDIF LT3CPDIF LT3CGAPC
LT3CPDIF
LT3CPHAR
LT3CPTRC
MVGAPC MVGGIO MVGAPC
NS4PTOC EF4LLN0
EF4PTRC
EF4RDIR
GEN4PHAR
PH1PTOC
EF4PTRC
EF4RDIR
PH1PTOC
OC4PTOC OC4LLN0
GEN4PHAR
PH3PTOC
PH3PTRC
GEN4PHAR
PH3PTOC
PH3PTRC
OV2PTOV GEN2LLN0
OV2PTOV
PH1PTRC
OV2PTOV
PH1PTRC
PCFCNT PCGGIO PCFCNT
PHPIOC PHPIOC PHPIOC
PRPSTATUS RCHLCCH RCHLCCH
SCHLCCH
QCBAY QCBAY BAY/LLN0
QCRSV QCRSV QCRSV
REFPDIF REFPDIF REFPDIF
ROV2PTOV GEN2LLN0
PH1PTRC
ROV2PTOV
PH1PTRC
ROV2PTOV
SCILO SCILO SCILO
SCSWI SCSWI SCSWI
Table continues on next page
Section 1 1MRK 504 160-UEN A
Introduction
12
Commissioning manual

Function block name Edition 1 logical nodes Edition 2 logical nodes
SESRSYN RSY1LLN0
AUT1RSYN
MAN1RSYN
SYNRSYN
AUT1RSYN
MAN1RSYN
SYNRSYN
SINGLELCCH - SCHLCCH
SLGAPC SLGGIO SLGAPC
SMBRREC SMBRREC SMBRREC
SMPPTRC SMPPTRC SMPPTRC
SP16GAPC SP16GGIO SP16GAPC
SPC8GAPC SPC8GGIO SPC8GAPC
SPGAPC SPGGIO SPGAPC
SSCBR SSCBR SSCBR
SSIMG SSIMG SSIMG
SSIML SSIML SSIML
SXCBR SXCBR SXCBR
SXSWI SXSWI SXSWI
T3WPDIF T3WPDIF T3WGAPC
T3WPDIF
T3WPHAR
T3WPTRC
TEIGAPC TEIGGIO TEIGAPC
TEILGAPC TEILGGIO TEILGAPC
TMAGAPC TMAGGIO TMAGAPC
TRPTTR TRPTTR TRPTTR
UV2PTUV GEN2LLN0
PH1PTRC
UV2PTUV
PH1PTRC
UV2PTUV
VMMXU VMMXU VMMXU
VMSQI VMSQI VMSQI
VNMMXU VNMMXU VNMMXU
VSGAPC VSGGIO VSGAPC
WRNCALH WRNCALH WRNCALH
ZCLCPSCH ZCLCPLAL ZCLCPSCH
ZCPSCH ZCPSCH ZCPSCH
ZCRWPSCH ZCRWPSCH ZCRWPSCH
ZCVPSOF ZCVPSOF ZCVPSOF
ZMFPDIS ZMFLLN0
PSFPDIS
ZMFPDIS
ZMFPTRC
ZMMMXU
PSFPDIS
PSFPDIS
ZMFPDIS
ZMFPTRC
ZMMMXU
1MRK 504 160-UEN A Section 1
Introduction
13
Commissioning manual

14