ABB CAP 501 Guide

Relay Setting Tools
CAP 501
Installation and Commissioning Manual
$%%

1MRS751270-MEN
Issue date: 31.01.2000
Program revision: 2.0.0
Documentation version: B
Copyright © 2000 ABB Substation Automation Oy
All rights reserved.
CAP 501
Relay Setting Tools
Installation and
Commissioning Manual
ABB Automation
3
Notices
Notice 1
The information in this document is subject to change without notice and should not
be construed as a commitment by ABB. ABB assumes no responsibility for any error
that may occur in this document.
Notice 2
This document complies with the CAP 501 version 2.0.0.
Notice 3
Additional information may be found in the Release Notes.
Trademarks
Microsoft is a registered trademark of Microsoft Corporation.
Windows NT is a registered trademark of Microsoft Corporation.
Intel and Pentium are registered trademarks of Intel Corporation.
Other brand or product names are trademarks or registered trademarks of their respective holders.
All Microsoft products referenced in this document are either trademarks or registered trademarks of Microsoft
Corporation.

1MRS751270-MEN Installation and Commissioning Manual CAP 501
Contents
ABB Automation 5
Contents
Page
Notices ..................................................................................................3
Contents................................................................................................5
1 Introduction......................................................................................8
1.1 Contents..............................................................................................8
1.1.1 Software .......................................................................................8
1.1.2 Documentation..............................................................................8
1.1.3 Hardware......................................................................................9
2 Requirements.................................................................................10
2.1 CAP 501 requirements......................................................................10
2.1.1 Software requirements................................................................10
2.1.2 Hardware requirements...............................................................10
2.1.3 Additional requirements ..............................................................11
3 Installation......................................................................................12
3.1 Overview...........................................................................................12
3.1.1 Product’s current version ............................................................12
3.1.2 About older product versions.......................................................12
3.1.3 Non-forced installation................................................................12
3.1.4 Forced installation.......................................................................12
3.1.5 Applications running at install-time..............................................12
3.1.6 System-wide product interdependencies.....................................13
3.1.6.1 Multiple installations of the kernel software...........................13
3.1.6.2 MicroSCADA service............................................................13
3.1.6.3 The Windows NT MicroSCADA user account.......................13
3.1.6.4 Kernel incompatibility issues.................................................13
3.2 Software installation procedure outlined............................................14
3.3 Installing the software........................................................................15

CAP 501
Contents Installation and Commissioning Manual 1MRS751270-MEN
ABB Automation
6
3.3.1 Starting the installation................................................................15
3.3.2 Installation Wizard.......................................................................16
3.3.2.1 Welcome...............................................................................16
3.3.2.2 Product License Agreement..................................................17
3.3.2.3 System Information 1............................................................17
3.3.2.4 System Information 2............................................................18
3.3.2.5 System Information 3............................................................19
3.3.2.6 Select - forced installation.....................................................20
3.3.2.7 Select - non-forced installation..............................................21
3.3.2.8 Destination Drive...................................................................22
3.3.2.9 Installing................................................................................24
3.3.2.10 MicroSCADA user account....................................................24
3.3.2.11 MicroSCADA Service Access Manager.................................25
Overview................................................................................................. 25
Purpose.................................................................................................... 25
Granting the rights to a group ................................................................. 26
Revoking the rights from a group ........................................................... 26
Saving the configuration......................................................................... 26
Discarding changes to the configuration................................................. 26
3.3.2.12 Installation completed ...........................................................27
3.3.2.13 System reboot.......................................................................27
3.3.3 Cancelling the installation............................................................27
3.3.4 CAP 501 program folder..............................................................28
3.3.4.1 Shortcut to the CAP 501 program folder................................29
3.4 Uninstalling the software....................................................................29
4 Commissioning ..............................................................................30
4.1 CAP 501 commissioning....................................................................30
5 Troubleshooting.............................................................................31
5.1 Insufficient user rights to install..........................................................31
5.2 MicroSCADA service is running.........................................................31
5.3 Failing to install the MicroSCADA service..........................................32
5.4 Troubleshooting destination drive error messages.............................32
5.5 Insufficient disk space........................................................................34
5.6 No suitable destination drive available...............................................35

1MRS751270-MEN Installation and Commissioning Manual CAP 501
Contents
ABB Automation 7
5.7 Incompatible SYS 500 and/or COM 500 installed..............................35
5.8 Miscellaneous ...................................................................................36
5.8.1 Repaired Windows NT installations.............................................36
5.8.2 TEMP environment variable........................................................36
6 References......................................................................................37
Index....................................................................................................38

CAP 501
Introduction Installation and Commissioning Manual 1MRS751270-MEN
ABB Automation
8
1 Introduction
This chapter describes the contents of CAP 501.
1.1 Contents
1.1.1 Software
Categorization of the software:
Base System Kernel software, additional base tools and services,
providing a framework for the object types and tools.
RED 500 Support RED 500 object types and the RED Relay Tool for
parameterization of RED 500 series relays.
SPACOM Support SPACOM object type and the SPA Relay Tool for
parameterization of SPACOM series relays.
DR-Collector Tool DR-Collector Tool for working with the disturbance
recorders.
Documentation CAP 501 documentation in PDF format and an installer for
installing the Acrobat®1 Reader (version 3.01) from Adobe
Corporation. The Acrobat Reader is needed to view the
documentation.
This ategorization is also present as installation options in the CAP 501 installation
application.
1.1.2 Documentation
CAP 501 manuals are listed in Table 1.
1Acrobat is a registered trademark of Adobe Corporation.

1MRS751270-MEN Installation and Commissioning Manual CAP 501
Introduction
ABB Automation 9
Manual Code Description
CAP 501
Installation and
Commissioning Manual
1MRS751270-MEN Provides installation and
commissioning instructions for CAP
501 software.
CAP 501
Operator’s Manual 1MRS751271-MUM Provides information on using the base system functions of CAP 501.
SM/RED
Configuration Manual 1MRS751392-MEN Provides information on using the object types for the RED 500 series of
relays.
SM/SPACOM
Configuration Manual 1MRS751393-MEN Provides information on using the SPACOM object type.
RED Relay Tool
Operator’s Manual 1MRS751383-MUM Provides information on using the RED Relay Tool.
SPA Relay Tool
Operator’s Manual 1MRS751385-MUM Provides information on using the SPA Relay Tool.
DR-Collector Tool
Operator’s Manual 1MRS751387-MUM Provides information on using the DR- Collector Tool.
Release Notes 1MRS751730-MZA Provides general information on this
release of CAP 501.
Table 1. CAP 501 Manuals.
Manuals are shipped in printed and in electronic format.
1.1.3 Hardware
Table 2 lists the communication cables included in the CAP 501 delivery.
Cable Communication Type Relays
1MKC950001-1 Opto RED500
SPA-ZP 17A3 RS 232 SPAC
SPA-ZP 5A3 RS 485 SPA
SPA-ZP 6A2 RS 485 SACO
SPA-ZP 21A RS 485 SACO
Table 2. Communication hardware.

CAP 501
Requirements Installation and Commissioning Manual 1MRS751270-MEN
ABB Automation
10
2 Requirements
This chapter describes the requirements for installing the CAP 501 software.
2.1 CAP 501 requirements
CAP 501 v. 2.0.0 sets the following hardware and software requirements on the PC.
Notice also the kernel-related dependencies, explained in section 3.1.6.
2.1.1 Software requirements
Table 3 lists the software requirements set by CAP 501.
Item Required
Operating system Microsoft®2Windows NT®34.0 Workstation. It is
recommended to have the Service Pack 5 installed.
Network Windows NT Network software installed with at least one
network protocol (e.g. TCP/IP).
Table 3. CAP 501 software requirements.
2.1.2 Hardware requirements
Table 4 lists the hardware requirements set by CAP 501.
2Microsoft is a registered trademark of Microsoft Corporation.
3Windows NT is a registered trademark of Microsoft Corporation.