ABB DPA UPScale ST40 User manual

© Copyright 2017 ABB, All rights reserved
User Manual
DPA UPScaleTM ST S2
10 – 200 kW

Modifications reserved
Page 2/79
Document information
File name
: 4NWP101759R0001_OPM_ABB_DPA_UPSCALE_ST_S2-10-200kW_EN_REV-C.docx
UPS model
:
DPA UPScale ST S2
Date of issue
: 10.12.2015
Article number
: 4NWP101759R0001
Document number
: 4NWD002986
Revision
: C
Foreword
This UPS operates with mains, battery or bypass power. It contains components that carry high
currents and voltages. The properly installed UPS is grounded to earth and IP20 rated against electric
shock and foreign objects. Installation and service have to be performed by the manufacturer’s
qualified technicians or their certified service partners.
COMMISSIONING AND OPERATIONS INSIDE THE UPS
MUST BE PERFORMED BY A CERTIFIED SERVICE
ENGINEER FROM THE MANUFACTURER OR FROM AN
AGENT CERTIFIED BY THE MANUFACTURER.
BY NOT FULFILLING THIS OBLIGATION, THE
PRODUCT MAY LOSE ITS WARRANTY
This user manual contains guidelines for delivery, installation and commissioning of the UPS, and is
intended for personnel who plan the installation, commissioning, use and service of the UPS. The
reader is expected to know the fundamentals of electricity, wiring, electrical components and
electrical schematic symbols.
CAREFULLY READ THE USER MANUAL BEFORE
OPERATING THE UPS OR WORKING ON IT.

Modifications reserved
Page 3/79
Contents
1Safety regulation ....................................................................................... 6
1.1 Safety rules .......................................................................................................... 6
1.2 Safety symbols and warnings ............................................................................. 7
2General information................................................................................... 8
2.1 Declaration of safety conformity and CE marking.............................................. 8
2.2 Nameplate and identification .............................................................................. 9
3System description.................................................................................. 10
3.1 System architecture........................................................................................... 11
3.2 Main elements description ................................................................................ 12
3.2.1 Single line diagram.........................................................................................................................12
3.2.2 Functional description ....................................................................................................................12
3.2.3 Control and monitoring ..................................................................................................................14
3.3 Multi cabinet configuration ............................................................................... 15
3.4 Operating modes ............................................................................................... 16
3.4.1 Mode “ON-LINE” ...........................................................................................................................16
3.4.2 Mode “OFF-LINE” (Eco or bypass mode)........................................................................................17
3.4.3 Mode “ON-BATTERY” (Battery mode) ............................................................................................18
3.4.4 Maintenance bypass ......................................................................................................................19
4Packing, transportation & storage .......................................................... 20
4.1 Packing & transportation................................................................................... 21
4.2 Unpacking.......................................................................................................... 22
4.2.1 Standard package (film) .................................................................................................................22
4.2.2 Sea freight light package (cardboard box) ...................................................................................... 23
4.2.3 Sea freight cases (wooden box) ..................................................................................................... 24
4.3 Storage............................................................................................................... 25
4.3.1 UPS...............................................................................................................................................25
4.3.2 Batteries ........................................................................................................................................25
5Installation ............................................................................................... 26
5.1 Environmental condition.................................................................................... 26
5.1.1 Climatic conditions.........................................................................................................................26
5.1.2 Biological conditions ......................................................................................................................26
5.1.3 Mechanical active substance..........................................................................................................26
5.1.4 Chemical active substance.............................................................................................................26
5.1.5 Mechanical conditions....................................................................................................................26
5.2 Enviromental condition for UPS with inside battery modules ......................... 26
5.2.1 Climatic conditions.........................................................................................................................26
5.3 UPS and battery location .................................................................................. 27
5.4 UPS connections ............................................................................................... 28

Modifications reserved
Page 4/79
5.4.1 Input connections...........................................................................................................................29
5.4.1.1 Mains supply and earth connection ...............................................................................29
5.4.1.2 Single input feed............................................................................................................30
5.4.1.3 Dual input feed ..............................................................................................................30
5.4.2 Output connections........................................................................................................................31
5.4.2.1 Load connection ...........................................................................................................31
5.5 Internal batteries ................................................................................................32
5.5.1 Internal battery modules DPA UPScale ST S2 40...........................................................................32
5.5.2 Internal battery modules DPA UPScale ST S2 60...........................................................................32
5.6 External batteries ...............................................................................................34
5.6.1 External battery configuration .........................................................................................................34
5.6.2 Connection of external battery cabinet for DPA UPScale™.............................................................36
5.6.3 Connection of external separate battery for DPA UPScaleTM ...........................................................37
5.6.4 Connection of external common battery for DPA UPScaleTM ...........................................................37
5.7 Electrical wiring..................................................................................................38
5.7.1 Cable sections and fuse ratings......................................................................................................38
5.7.2 Terminal connections .....................................................................................................................38
5.7.3 Single input feed (standard version) ................................................................................................40
5.7.3.1 Block diagram ...............................................................................................................40
5.7.3.2 Cable sections...............................................................................................................40
5.7.4 Dual input feed (optional version) ....................................................................................................41
5.7.4.1 Block diagram ...............................................................................................................41
5.7.4.2 Cable sections...............................................................................................................41
6Control and monitoring ........................................................................... 42
6.1 Control panel module.........................................................................................42
6.1.1 Status and alarm indication ............................................................................................................42
6.1.2 Buttons ..........................................................................................................................................43
6.2 LCD description .................................................................................................44
6.2.1 Status ............................................................................................................................................44
6.2.2 Main menu .....................................................................................................................................45
6.2.3 Commands ....................................................................................................................................45
6.3 Metering .............................................................................................................45
6.3.1 Measurements ...............................................................................................................................45
6.3.2 Event log........................................................................................................................................46
6.3.3 UPS Data .......................................................................................................................................46
6.3.4 Set-up user ....................................................................................................................................47
6.3.5 Set-up service................................................................................................................................47
6.4 Communication interfaces.................................................................................48
6.4.1 Customer interface and DRY PORTs ..............................................................................................48
6.4.1.1 Output interfaces: terminal blocks x2 (DRY PORTs)........................................................48
6.4.1.2 Input interfaces: teminal blocks X1.................................................................................48
6.4.2 JD1 / RS232 smart port computer interface ...................................................................................50
6.4.3 USB computer interface .................................................................................................................50
7Commissioning........................................................................................ 51
7.1 Start-up procedure ............................................................................................51
7.2 Shut-down procedure ........................................................................................53
7.2.1 Remote shutdown..........................................................................................................................54

Modifications reserved
Page 5/79
7.2.2 Generator ON facilities ...................................................................................................................54
7.3 Manual bypass................................................................................................... 55
7.3.1 From invert to bypass ....................................................................................................................55
7.3.2 From bypass to inverter .................................................................................................................56
7.4 Adding & replacement of a power module ....................................................... 57
7.4.1 In a single-module system.............................................................................................................. 57
7.4.1.1 How to extract a ups-module in single module systems.................................................57
7.4.1.2 How to fit back a ups-module in single-module-systems ............................................... 58
7.4.2 In a redundant multi-module system...............................................................................................60
7.4.2.1 How to extract a module in redundant multi-module system..........................................60
7.4.2.2 How to insert a module in a redundant multi module system .........................................61
7.4.3 In capacity multi-module system ....................................................................................................62
7.4.3.1 How to extract a module in a capacity multi-module system.......................................... 62
7.4.3.2 How to fit back a module in a capacity multi-module system ......................................... 63
7.5 Multi cabinet configuration ............................................................................... 65
7.5.1 DIP switch SW1-6..........................................................................................................................66
8Options .................................................................................................... 67
8.1 System ............................................................................................................... 67
8.1.1 Backfeed protection.......................................................................................................................67
8.2 Power module.................................................................................................... 68
8.2.1 Battery start ...................................................................................................................................68
8.2.2 Battery enhancement.....................................................................................................................68
8.2.3 Output short capability 3 x In.......................................................................................................... 69
8.3 Wiring ................................................................................................................. 69
8.3.1 Halogen free cable ......................................................................................................................... 69
8.4 Control and monitoring...................................................................................... 69
8.4.1 Network interface cards .................................................................................................................70
8.4.1.1 CS141 basic .................................................................................................................71
8.4.1.2 CS141 advanced .......................................................................................................... 71
8.4.1.3 CS141 modbus.............................................................................................................72
9Maintenance & troubleshooting.............................................................. 73
9.1 General maintenance......................................................................................... 73
9.1.1 User responsibilities .......................................................................................................................73
9.1.2 Preventative maintenance ..............................................................................................................73
9.1.3 Deep battery test ........................................................................................................................... 74
9.1.4 Battery maintenance, disposal and recycling ..................................................................................74
9.2 Troubleshooting................................................................................................. 74
9.2.1 Alarms ...........................................................................................................................................74
9.2.2 Menu, commands, event log and measurements ...........................................................................74
9.2.3Fault identification and rectification .................................................................................................75
10 Attachments.......................................................................................... 76
10.1 Technical data sheet............................................................................. 76

Modifications reserved
Page 6/79
1Safety regulation
1.1 Safety rules
This UPS operates with mains, battery or bypass power. It contains components that carry high
currents and voltages. The properly installed UPS is grounded to earth and IP20 rated against electric
shock and foreign objects. Installation and service have to be performed by the manufacturer’s
qualified technicians or their certified service partners.
WARNING!
THERE IS DANGER OF ELECTRICAL SHOCK
This user manual contains guidelines for delivery, installation and commissioning of the UPS, and is
intended for personnel who plan the installation, commissioning, use and service of the UPS. The
reader is expected to know the fundamentals of electricity, wiring, electrical components and
electrical schematic symbols.
NOTE!
READ THE INFORMATION IN ORDER TO AVOID EQUIPMENT DAMAGE
The only user operations permitted are:
•Use of the LCD control panel (LCD) and of the maintenance bypass
•Start-up and shut-down of the UPS user field (except during commissioning start-up)
•Operation of additional connectivity modules:
•SNMP adapters and their software
•Modem/GSM or modem/Ethernet adapters and their software
The user must take the precautions set out in this manual and only perform the operations described.
The UPS operator must adhere to the instructions in this manual. Any deviations from the instructions
could be dangerous to the user or could cause accidental load loss.
THE MANUFACTURER DOES NOT TAKE ANY RESPONSIBILITY FOR DAMAGE CAUSED BY
INCORRECT USE OF THE UPS.
WARNING!
IT IS PROHIBITED TO REMOVE ANY SCREWS FROM THE UPS OR FROM
THE BATTERY CABINET. THERE IS A DANGER OF ELECTRIC SHOCK.

Modifications reserved
Page 7/79
WARNING!
HIGH FAULT CURRENTS (LEAKAGE CURRENTS):
BEFORE CONNECTING THE MAINS, YOU MUST ENSURE THAT THERE IS
A PROPER EARTH CONNECTION!
WARNING!
THE USER MUST DISPLAY A WARNING SHIELD ON ALL PRIMARY UPS
CIRCUIT BREAKERS. THE SERVICE PERSONNEL HAS TO BE INFORMED
ABOUT DANGEROUS VOLTAGES. THE WARNING PANELS MUST CONTAIN
THE FOLLOWING TEXT: “ BEFORE STARTING WITH MAINTENANCE WORK
ON THE CIRCUIT BREAKERS, MAKE SURE THE UPS IS ISOLATED.”
1.2 Safety symbols and warnings
PROTECTIVE GROUNDING TERMINAL
A terminal which must be connected to earth ground prior to making any
other connection to the equipment.
A terminal to which or from which a direct current or voltage may be
applied or supplied.
This symbol indicates the word “phase”.
ON The principal power switch is in the “ON” position
OFF The principal power switch is in the “OFF” position.
CAUTION: REFER TO MANUAL
Refer to the Operator’s manual for more information
DANGER: RISK OF ELECTRIC SHOCK
There is a risk of electric shock present, and you should observe
associated warnings. The UPS contains high voltages.

Modifications reserved
Page 8/79
2General information
WARNING!
THIS IS A PRODUCT FOR COMMERCIAL AND INDUSTRIAL APPLICATION
IN THE SECOND ENVIRONMENT AS DEFINED IN IEC/EN 62040-2
CHAPTER 4 – INSTALLATION RESTRICTIONS OR ADDITIONAL
MEASURES MAY BE NEEDED TO PREVENT DISTURBANCES
The UPS must be installed according to the recommendations in this manual. To operate the UPS at
peak efficiency, your installation site should meet the environmental parameters outlined in this
manual. Excessive amounts of dust in the operating environment of the UPS may cause damage or
lead to malfunction. The UPS should always be protected from weather and sunshine. If you intend
to operate the system at an altitude higher than 1000 m, contact your local sales or service office for
important information about high-altitude operation. The operating environment must meet the weight,
airflow, size and clearance requirements specified in the technical datasheet.
Under no circumstances should the UPS be installed in an airtight room, in the presence of flammable
gases, or in an environment exceeding the specification. The basic environmental requirements of the
UPS are:
•Ambient temperature Range: 0 to +40˚C (32 – 104˚F)
•Recommended operating Range: +20 to +25˚C (68 – 77˚F)
•Maximum relative Humidity: 95% (non-condensing)
The UPS cabinet uses forced air cooling to regulate internal component temperature. Air inlets are
sited in the sides and front of the cabinet, at the bottom, and air outlets are sited in the rear of the
cabinet. You must allow clearance at the back of the cabinet for proper air circulation. Refer to
chapter 5.3: UPS and battery location.
2.1 Declaration of safety conformity and CE marking
The product has the CE marking in compliance with the following European directives:
•Low Voltage Directive: 2006/95/EC
•EMC Directive: 2004/108/EC
Declaration of conformity with UPS harmonized standards and directives
EN 62040-1-1 (Safety) and EN 62040-2 (EMC) are available in the annex 1
Product Standards Standards
Safety Standard: IEC/EN 62040-1 IEC/EN 60950-1
Electromagnetic Compatibility
Standard (EMC):
IEC/EN 62040-2
Emission cat. C3
Immunity cat. C3
IEC/EN 61000-6-2
IEC/EN 61000-6-4
IEC/EN 61000-4-2
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
Performance Standard: IEC/EN 62040-3

Modifications reserved
Page 9/79
The DPA UPScale TM will provide your critical equipment with a steady and reliable power supply for
many years.
The unique and modular UPS DPA UPScale belongs to the newest generation of midrange three-
phase UPS systems. High reliability, low operating costs and excellent electrical performance are only
some of the highlights of this innovative UPS solution.
The criteria and methods implemented at ABB for the design and manufacture correspond to the
most stringent quality standards.
The manufacturer is certified successfully in every area required by the international standard ISO
9001/EN 29001. The UPS is certified according to the norm IEC 62 040-3 and VDE 0558 Part 530 is
also accomplished.
The UPS has the
Classification Code VFI-SS-111.
2.2 Nameplate and identification
The technical specifications of the equipment are provided on the nameplate, which is situated at the
front of the UPS. Check if it corresponds to the purchased material mentioned in the delivery note.
Fig 2.2-1: Nameplate
TYPE PRODUCT DESCRIPTION DIMENSIONS
S2UPxxx
DPA UPScale ST 40
Cabinet (550x1135x770mm)
S3UPxxx
DPA UPScale ST 60
Cabinet (550x1975x770mm)
S4UPxxx
DPA UPScale ST 80
Cabinet (550x1135x770mm)
S6UPxxx
DPA UPScale ST 120
Cabinet (550x1975x770mm)
S0UPxxx
DPA UPScale ST 200
Cabinet (550x1975x770mm)

Modifications reserved
Page 10/79
3System description
The DPA UPScale ST S2 is a three-phase transformerless uninterruptible power supply (UPS). It is a
true on-line double conversion UPS providing quality power for sensitive equipment. It is a modular
UPS consisting of:
-DPA UPScale modules, rated power 10kW or 20kW
-Maintenance bypass switch
-Incoming and outcoming terminals
-Communication interfaces
-Parallel interface (option)
-System graphical display (option)
-Internal battery modules (option)
The DPA UPScale ST S2 family has five models available:
DPA UPScale S2 ST40 ST60 ST80 ST120 ST200
Max rated power 40 kW 60 kW 80 kW 120 kW 200 kW
Max number of DPA
UPS modules 2 3 4 6 10
Internal battery
modules Yes Yes No No No

Modifications reserved
Page 11/79
3.1 System architecture
The DPA UPScale ST S2 System has a decentralized parallel architecture (DPA). Each DPA UPScale
module has its own:
-Rectifier and inverter
-DC booster
-Static bypass
-Battery connection
-Control logic
-LCD control panel
Fig 3.1-1: System architecture
Therefore, the UPS does not have common components. This offers high availability and no single
point of failure.
There are two types of DPA Upscale modules, as follows:
Module type UPScale M 10 UPScale M 20
Rated output power 10 kW 20 kW
Weight 18.6 kg 21.5 kg
Dimensions
(WxHxD) 488x132x540
The DPA UPScale Modules are “safe-swappable” - no disturbance to the operation of the load is
caused by inserting or extracting a module from a system while it is powered.

Modifications reserved
Page 12/79
3.2 Main elements description
3.2.1 Single line diagram
Fig 3.2.1-1: Single line diagram
3.2.2 Functional description
Section Component Functional Description
Main input terminals
1L1 Rectifier mains terminal, Phase 1 Provides a connection between the utility supply
and the rectifier input
1L2 Rectifier mains terminal, Phase 2
1L3 Rectifier mains terminal, Phase 3
1N Neutral terminal
PE Earth terminal
Bypass input terminals
2L1 Bypass Main Input Terminal, Phase 1 Provides a connection between the bypass
supply and UPS bypass input
2L2 Bypass Main Input Terminal, Phase 2
2L3 Bypass Main Input Terminal, Phase 3
2N
Neutral terminal
System output terminals
3L1 System Output Terminal, Phase 1 Provides a connection between the UPS system
and the load
3L2
System Output Terminal, Phase 2
3L3
System Output Terminal, Phase 3
3N
Neutral terminal
PE Earth terminal

Modifications reserved
Page 13/79
Battery terminals
+,N,- Battery Terminal Provides a connection between the external
battery and the UPS
Battery circuit breaker
FX-1 Battery circuit breaker Module 1 Battery overcurrent protective device (MCB).
FX-2
Battery circuit breaker Module 2
Each power module has a battery breaker
FX-3
Battery circuit breaker Module 3
FX-4
Battery circuit breaker Module 4
FX-5 Battery circuit breaker Module 5
FX-6
Battery circuit breaker Module 6
FX-7
Battery circuit breaker Module 7
FX-8
Battery circuit breaker Module 8
FX-9 Battery circuit breaker Module 9
FX-10
Battery circuit breaker Module 10
Maintenance bypass switch
IA1 Maintenance bypass switch
The manual bypass switch connects the load
direct to the bypass input supply when it is
closed (ON). The UPS is isolated for services or
maintenance work
Power Modules
A001 Power Module 1
The power module has a rated power of 10kW or
20kW.
A002 Power Module 2
It has a decentralized parallel architecture
(DPA) consisting of
A003 Power Module 3 -Rectifier
A004
Power Module 4
- DC boost converter
A005
Power Module 5
- Inverter
A006 Power Module 6 - Static bypass
A007 Power Module 7 - Control logic
A008
Power Module 8
-LCD control panel
A009 Power Module 9
The max number of modules inside the frame,
depends of the chosen cabinet.
A010 Power Module 10
Internal battery modules
Battery Module
Each battery module has the capacity to
take up to 10 VLRA battery blocks of 12 V
7/9 Ah. Max number of battery blocks per
power module is 50. The internal battery
modules are only available for ST40 and
ST60 UPS model
Backfeed protection
K1 Mains backfeed contactor
(option)
Prevents the occurrence of any hazardous
voltage at the rectifier mains terminal in the
event of an AC failure due to backfeed from
the rectifier modules powered by the battery
K2 Bypass backfeed contactor
(option)
Prevents the occurrence of any hazardous
voltage at the bypass input terminal in the
event of an AC failure due to backfeed from
the inverter modules powered by the battery

Modifications reserved
Page 14/79
3.2.3 Control and monitoring
Section Component Functional Description
Customer interface
X1 Customer input dry ports
Up to 5 input dry contacts used for remote
shut down and generator operation facilities,
battery temperature sensor or customer
function
X2 Customer output dry ports
Up to 5 output dry contacts used for
signaling UPS status (eg, mains failure, load
on inverter, battery low, common alarm, etc.)
JD1 RS232 Smart Port Computer Interface
RS-232 serial port to monitor the UPS using
the Wavemon software
USB Computer Interface
USB port to monitor the UPS using the
Wavemon software
SLOT1
Modem
Optional slot for modem/Ethernet card
SLOT2
SNMP
Optional slot for SNMP card
Parallel interface (optional)
JD8 Parallel Interface
The parallel interface is used to connect up
to 4 UPS frames in parallel (max number of
modules: 20)
SW1-6 Multi cabinet configuration switch
Determine the “position of the cabinet” in a
multi-cabinet chain
X1 Sync input
Allows to synchronize the output of a UPS
system (single UPS or parallel system) with
another UPS system, another electrical
equipment (AC) or an external grid.
X2 External manual bypass / External output
breaker input
Auxiliary signals from external manual
bypass switch and external output breaker
providing information of the status
(open/closed) for parallel system
configuration
Fig 3.2.3-1: Customer and Parallel interfaces

Modifications reserved
Page 15/79
3.3 Multi cabinet configuration
The DPA UPScale ST S2 may be paralleled to increase the power capacity up to 400 kW in steps of
10 or 20 kW. A maximum of 20 modules can be paralleled. The following system configurations are
available:
DPA UPScale S2 ST40 ST60 ST80 ST120 ST200
Number of modules
per frame
2 3 4 6 10
Parallel frames
per system
4 4 4 3 2
Max number of
modules per system
8 12 16 18 20
Max. total system
capacity w/o redundancy
160 kW 240 kW 320 kW 360 kW 400 kW
The multiple cabinet systems are delivered with:
UPS A UPS B UPS C
System graphical display •- -
Parallel interface •••
Parallel cable ••-
The start-up of a multiple cabinet systems is an operation which can be performed by a service
engineer form the manufacturer or by a service engineer from an agent certified by the manufacturer.
Please refer to the service manual to perform this operation.
Fig 3.3-1: Multi cabinet configuration

Modifications reserved
Page 16/79
3.4 Operating modes
3.4.1 Mode “ON-LINE”
In on-line mode, the load is connected to the inverter (INV) and the rectifier (Line1) is supplied by the
main utility supply. The on-line mode protects the load from any utility main disturbance or failure.
Fig 3.4.1-1: “ON LINE” operating mode
The on-line mode status is shown in the mimic of control panel per module as follows:
LED Indicator Color
LINE 1 Green
LINE 2 Green
BYPASS OFF
INVERTER Green
BATTERY Green
Fig 3.4.1-2: “ON LINE” control panel mimic
In the unlikely event of an inverter fault or overload condition, the UPS will transfer the load
automatically and without interruption to the static bypass (transfer time = 0 s).

Modifications reserved
Page 17/79
3.4.2 Mode “OFF-LINE” (Eco or bypass mode)
In "OFF-Line Mode”, the load is supplied from the bypass mains (LINE 2) through the static bypass
(BYPASS). The Inverter is OFF.
Fig 3.4.2-1: “OFF LINE” operating mode
The OFF-Line mode status is shown in the mimic of the control panel per module as follow:
LED Indicator Color
LINE 1 Green
LINE 2 Green
BYPASS Green
INVERTER OFF
BATTERY Green
Fig 3.4.2-2: “OFF LINE” control panel mimic
In off-line mode, the battery charger remains active. In the event of a bypass mains (LINE 2) failure,
the load will be automatically transferred from mains to inverter within 5 ms (this is valid for single and
parallel systems). If the utility mains supply (LINE 1) is not available, the energy is supplied by the
battery.
Bypass mode is recommended only if the loads can tolerate interruptions of 3-5 ms (transfer time
from bypass mode to on-line mode)
NOTE!
TO OBTAIN THE BEST POWER SECURITY, IT IS RECOMMENDED TO RUN
THE UPS ON NORMAL OPERATION MODE, IE, UPS MODE (MODE "ON-
LINE”)

Modifications reserved
Page 18/79
3.4.3 Mode “ON-BATTERY” (Battery mode)
In ON-Battery Mode, the load is connected to the inverter (INV) and the inverter is supplied by the
battery. The utility main supply is not available (LINE 1)
Fig 3.4.3-1: “ON BATTERY” operating mode
The ON-Battery Mode status is shown in the mimic of the control panel per module as follow:
LED Indicator Color
LINE 1 OFF
LINE 2 Green
BYPASS OFF
INVERTER Green
BATTERY Green
Fig 3.4.3-2: “ON BATTERY” control panel mimic

Modifications reserved
Page 19/79
3.4.4 Maintenance bypass
The maintenance bypass mode is achieved using the IA1 bypass switch on the front of the UPS:
POSITION OF SWITCH EFFECT
ON Bypass-Switch Closed (Load supplied directly from bypass mains)
OFF Bypass-Switch Open – Normal operating condition
(Load supplied by inverter)
Fig 3.4.4-1: “Maintenance bypass” operating mode
NOTE!
IN OPERATION MODE “MANUAL BYPASS,“ THE LOAD IS NOT
PROTECTED AGAINST ANY MAINS FAILURES OR MAINS DISTURBANCES.

Modifications reserved
Page 20/79
4Packing, transportation & storage
This chapter contains all the information necessary for the correct packing, transportation and
unpacking of the UPS.
NOTE!
IF THE UPS IS NOT INSTALLED IMMEDIATELY, THE FOLLOWING
GUIDELINES MUST BE FOLLOWED:
TRANSPORT:
UPS CABINETS AND/OR BATTERY CABINETS CAN FALL OVER. USE THE
SHIPPING BRACKETS ON THE REAR AND FRONT TO SECURE THE
CABINETS. DO NOT TILT THEM MORE THAN 10° FROM VERTICAL,
OTHERWISE THE CABINETS MAY TIP OVER.
POTENTIAL DANGERS:
- TILTING THE CABINET MIGHT DAMAGE THE SYSTEM AND
THEREFORE IT SHOULD NOT BE CONNECTED TO THE MAINS.
- IF IT TIPS, THE WEIGHT OF THE UPS COULD CAUSE SERIOUS
INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT IN THE
VICINITY.
STORAGE:
- THE UPS SHOULD BE STORED IN THE ORIGINAL PACKING AND
SHIPPING CARTON.
- THE RECOMMENDED STORING TEMPERATURE FOR THE UPS AND
BATTERIES IS BETWEEN +20°C AND +25°C.
- THE UPS AND THE BATTERY SETS MUST BE PROTECTED FROM
HUMIDITY > 95% (NON-CONDENSING).