ABB CONCEPTPOWER CLASSIC DPA-50 User manual

Conceptpower DPA
TM
S2 30 - 250 kVA
User Manual
04-3008_OPMCPDPA-S2_GB_121202
© Copyright 2012 ABB, All rights reserved.

Section-0
04-3008_CoverABB_OPMCPDPA-S2_GB_121202 Page 2/8
Printed in Switzerland – Modifications reserved
This page left intentionally blank

Section-0
04-3008_CoverABB_OPMCPDPA-S2_GB_121202 Page 3/8 ABB
Printed in Switzerland – Modifications reserved
GENERAL CONTENTS OF THE
USER MANUAL CONCEPTPOWER DPATM S2
0 SECTION-0:
0.1 FOREWORD
0.2 CONCEPTPOWER DPA™ S2 SYSTEM DESCRIPTION
1 SECTION-1:
1.1 MECHANICAL CHARACTERISTICS MX-FRAMES AND MODULES
1.2 SAFETY INSTRUCTIONS
1.2.1 GENERAL SAFETY INTRODUCTION
1.2.2 DESCRIPTION OF SYMBOLS USED IN THIS MANUAL
1.2.3 SYMBOLS, CONTROLS, AND INDICATORS
1.2.4 OPERATOR PRECAUTIONS
1.2.5 ENVIRONMENTAL CONSIDERATIONS
1.2.6 DECLARATION OF SAFETY CONFORMITY AND CE MARKING
1.2.7 INQUERIES
1.3 SYSTEM DESCRIPTION
1.3.1 GENERAL SYSTEM DESCRIPTION
1.3.2 CONCEPTPOWER DPATM S2 BASIC SYSTEM CONFIGURATION
1.3.3 QUALITY STANDARDS AND UPS CLASSIFICATION CODE
1.3.4 SINGLE/PARALLEL-MODULES OPERATION
1.3.5 SINGLE/MULTI-CABINET CONFIGURATIONS
1.4 DELVERY - TRANSPORT - STORAGE
1.4.1 INTRODUCTION
1.4.2 RECEIPT OF THE UPS AND VISUAL INSPECTION
1.4.3 UNPACKING
1.4.4 NAMEPLATE AND IDENTIFICATION
1.4.5 BATTERIES AND STORAGE
1.5 SITE PLANNING AND POSITIONING
1.5.1 PLANNING BEFORE THE INSTALLATION
1.5.2 POSITIONING OF UPS AND BATTERY CABINET
1.6 ELECTRICAL INSTALLATION
1.6.1 PREPARATION FOR THE INPUT CABLING
1.6.2 INSTALLATION CHECKLIST

Section-0
04-3008_CoverABB_OPMCPDPA-S2_GB_121202 Page 4/8 ABB
Printed in Switzerland – Modifications reserved
2 SECTION-2:
2.1 BLOCK DIAGRAM
2.1.1 WIRING AND BLOCK DIAGRAMS FOR ALL FRAMES AND MODULES
2.1.2 RECOMMENDED CABLE SECTIONS & FUSE RATINGS
2.1.3 BLOCK DIAGRAM CONCEPTPOWER DPATM
2.2 FRONT VIEW
2.2.1 FRONT VIEW OF MX-FRAMES
2.3 BATTERY CONNECTIONS
2.3.1 INTERNAL BATTERY MODULES
2.3.2 EXTERNAL BATTERY CABINET AND BATTERY CONNECTION
3 SECTION-3:
3.1 INTERFACING
3.1.1 SMART PORT JD1 ON EACH MODULE (SERIAL RS 232/SUB D9/MALE)
3.1.2 CUSTOMER INTERFACE AND DRY PORTS (VOLT-FREE CONTACTS)
3.1.3 JD11 / RS232 COMPUTER INTERFACE
3.1.4 JD12 / RS232 INTERFACE FOR MULTIDROP
3.1.5 USB/2 COMPUTER INTERFACE
4 SECTION-4:
4.1 OPERATION
4.1.1 COMMISSIONING
4.1.2 CONTROL PANEL
4.1.3 DESCRIPTION OF THE LCD
4.1.4 OPERATING MODES
5 SECTION-5:
5.1 OPERATION–PROCEDURES
5.1.1 START-UP PROCEDURE
5.1.2 SHUTDOWN PROCEDURE
5.1.3 LOAD TRANSFER: FROM INVERTER OPERATION TO MAINTENANCE BYPASS
5.1.4 LOAD TRANSFER: FROM MAINTENANCE BYPASS TO INVERTER OPERATIONS
5.2 REPLACEMENT OF UPS-MODULE
5.2.1 REPLACEMENT OF UPS-MODULE IN SINGLE-MODULE SYSTEMS
5.2.2 REPLACEMENT OF UPS-MODULE IN REDUNDANT MULTI-MODULE SYSTEM
5.2.3 REPLACEMENT OF A MODULE IN CAPACITY MULTI-MODULE SYSTEM

Section-0
04-3008_CoverABB_OPMCPDPA-S2_GB_121202 Page 5/8 ABB
Printed in Switzerland – Modifications reserved
6 SECTION-6:
6.1 MULTI-CABINET CONFIGURATION
6.1.1 CONCEPT OF MULTI-CABINET CONFIGURATION
6.1.2 INSTALLATION INSTRUCTIONS
6.1.3 COMMISSIONING OF MULTI-CABINET CONFIGURATION
7 SECTION-7:
7.1 MAINTENANCE
7.1.1 INTRODUCTION
7.1.2 USER RESPONSIBILITIES
7.1.3 ROUTINE MAINTENANCE
7.1.4 BATTERY TEST
7.1.5 BATTERY MAINTENANCE
7.1.6 BATTERY DISPOSAL AND RECYCLING
8 SECTION-8:
8.1 TROUBLESHOOTING
8.1.1 ALARMS
8.1.2 MENU, COMMANDS, EVENT LOG AND MEASUREMENTS,
8.1.3 FAULT IDENTIFICATION AND RECTIFICATION
9 SECTION-9:
9.1 OPTIONS
9.1.1 INTRODUCTION
9.1.2 REMOTE SHUTDOWN
9.1.3 GENERATOR ON FACILITIES
9.1.4 WAVEMON SHUTDOWN AND MANAGEMENT SOFTWARE
9.1.5 SNMP CARD/ADAPTER FOR NETWORK MANAGEMENT /REMOTE MONITORING

Section-0
04-3008_CoverABB_OPMCPDPA-S2_GB_121202 Page 6/8 ABB
Printed in Switzerland – Modifications reserved
10 SECTION-10: TECHNICAL DATA SHEET
10.1 CONCEPTPOWER DPA™ S2 SYSTEM DESCRIPTION
10.2 TECHNICAL CHARACTERISTICS
10.2.1 MECHANICAL CHARACTERISTICS MX-FRAMES AND MODULES
10.2.2 POWER SELECTION TABLE CONCEPTPOWER DPA MODULES
10.3 INPUT CHARACTERISTICS
10.3.1 GRAPH: INPUT PF VERSUS % LOAD
10.3.2 GRAPH: INPUT DISTORTION THDI VERSUS % LOAD
10.4 BATTERY CHARACTERISTICS
10.5 OUTPUT CHARACTERISTICS
10.5.1 GRAPH: AC – AC EFFICIENCY
10.5.2 GRAPH: OUTPUT POWER IN KW AND KVA VERSUS COSPHI
10.6 ENVIRONMENTAL CHARACTERISTICS
10.7 STANDARDS
10.8 COMMUNICATION
10.8.1 POWER MANAGEMENT DISPLAY (PMD)
10.8.2 MIMIC DIAGRAM
10.8.3 DISPLAY
10.8.4 CUSTOMER INTERFACES (TERMINALS X1….X4)
10.8.5 CUSTOMER INPUTS DRY PORTS: TERMINAL BLOCK X1
10.8.6 CUSTOMER OUTPUTS DRY PORTS: TERMINA BLOCKS X2, X3, X4
10.9 OPTIONS
10.9.1 SNMP CARD / WAVEMON MANAGEMENT SOFTWARE
10.9.2 BATTERY CABINETS
10.10 BATTERY AUTONOMIES
10.10.1 MX MODULES: EXAMPLES OF INTERNAL BATTERY AUTONOMY
10.10.2 MX MODULES: EXAMPLES OF EXTERNAL BATTERY AUTONOMY
10.11 INSTALLATION PLANNING
10.11.1 HEAT DISSIPATION PER MODULE WITH NON-LINEAR LOAD
10.12 WIRING AND BLOCK DIAGRAMS FOR ALL FRAMES AND MODULE
10.12.1 TERMINAL CONNECTIONS OVERVIEW
10.12.2 SINGLE FEED INPUT
10.12.3 DUAL FEED INPUT

Section-0
04-3008_CoverABB_OPMCPDPA-S2_GB_121202 Page 7/8 ABB
Printed in Switzerland – Modifications reserved
0.1 FOREWORD
The UPS System operates with mains, battery or bypass power. It contains components that carry high
currents and voltages. The properly installed UPS System is grounded to earth and IP 20 rated against
electrical shock and foreign objects. Installation and service have to be done by the manufacturer’s
qualified technicians or their authorized service partners.
OPERATIONS INSIDE THE UPS MUST BE PERFORMED
BY A SERVICE ENGINEER FROM THE MANUFACTURER
OR FROM AN AGENT AUTHORIZED BY THE
MANUFACTURER.
This user manual contains guidelines to check delivery, installing and commissioning of the UPS and is
intended for people who plan the installation, install, commission and use or service the UPS. The
reader is expected to know the fundamentals of electricity, wiring, electrical components and electrical
schematic symbols
CAREFULLY READ THE USER MANUAL BEFORE
OPERATING OR WORKING ON THE UPS.

Section-0
04-3008_CoverABB_OPMCPDPA-S2_GB_121202 Page 8/8 ABB
Printed in Switzerland – Modifications reserved
0.2 CONCEPTPOWER DPA™ S2 SYSTEM DESCRIPTION
In environments that demand zero downtime, continuous power protection availability is essential. In
order to respond to today’s dynamic IT and process-related environments that experience daily change
through new server technologies, migration and centralization, resilient and easily adaptable power
protection concepts are required.
CONCEPTPOWER DPA™ S2 is the foundation for continuous power protection availability of network-
critical infrastructures in enterprise data centers where business continuity has paramount importance
and in process control environment where manufacturing continuity is essential.
CONCEPTPOWER DPA™ S2’S is a second generation high-power-density (HPD), leading-edge
double-conversion power protection technology that has standardized on a modular component
approach which helps speed deployment, improve adaptability and increase system availability while
reducing total cost of ownership.
CONCEPTPOWER DPA™ S2’S is a unique on-demand architecture that integrates the power rack,
power distribution unit, back-up battery rack and monitoring and management solutions to allow easy
selection of optimized configurations.
CONCEPTPOWER DPA™ S2’S (Distributed Parallel Architecture) provides highest availability,
unmatched flexibility and at the same time lowest cost of ownership in IT environments.
This Technical Specification provides detailed technical information on the mechanical, electrical and
environmental performance of the CONCEPTPOWER DPA™ S2 that can support to give answers to
tender and end-user requirements. The CONCEPTPOWER DPA™ S2 was designed to respond to the
most stringent safety, EMC and other important UPS standards.
CONCEPTPOWER DPA™ S2 is a rack-mountable modular design. It offers 3-types of Racks (Frames)
and 3 types of DPA-Modules to accommodate a wide range of power requirements.
The three MX-Frames; Classic DPA-50, Triple DPA-150, Upgrade DPA-250 can accommodate the three
(3) MX-DPA-Modules types DPA 30 or 40 or 50 of: 30kVA/24kW - 40kVA/32kW - 50kVA/40kW power.
Key Features of CONCEPTPOWER DPA S2 Modules:
Highest Availability Near-zero down time
Modular, Decentralized Parallel Architecture (DPA)
High Power Density (up to 342kW / m2), Space-saving of expensive floor space
Small Footprint
Blade-server-friendly power No de-rating with leading PF loads
Full power from 0.9 lead to 0.8 lag
High Efficiency even with partial loads Energy cost saving during UPS-life-cycle
Efficiency up to 95.5%
(depending on Module power and type of load)
Very low input current distortion THDi Gen-set power and installation cost saving
THDi = < 3 - 4% for loads of 100 – 25 %

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 1/22 ABB
Printed in Switzerland – Modifications reserved
CONTENTS SECTION-1
1.1MECHANICAL CHARACTERISTICS MX-FRAMES AND MODULES..............................................2
1.2SAFETY INSTRUCTIONS...................................................................................................................3
1.2.1GENERAL SAFETY INTRODUCTION........................................................................................3
1.2.2DESCRIPITON OF SYMBOLS USED IN THIS MANUAL...........................................................3
1.2.3Symbols, Controls, and Indicators...............................................................................................4
1.2.4OPERATOR precautions.............................................................................................................5
1.2.5Environmental Considerations.....................................................................................................6
1.2.6Declaration of Safety conformity and CE marking.......................................................................6
1.2.7Inquiries .......................................................................................................................................6
1.3SYSTEM DESCRIPTION ....................................................................................................................7
1.3.1GENERAL SYSTEM DESCRIPTION..........................................................................................7
1.3.1.1Feature : Unique “Hot Swappable” Modules .......................................................................7
1.3.1.2Feature : Advanced-Booster Technology............................................................................7
1.3.1.3Feature : Flexible Battery Management (FBM) ...................................................................8
1.3.1.4Feature : DPA Technology - Decentralized Parallel Architecture........................................8
1.3.2Conceptpower DPATM S2 basic system configuration.................................................................9
1.3.3Quality Standards and ups classification code............................................................................9
1.3.4Single/Parallel-Modules operation.............................................................................................10
1.3.5Single/Multi-Cabinet Configurations..........................................................................................10
1.4DELVERY - TRANSPORT - STORAGE...........................................................................................11
1.4.1Introduction................................................................................................................................11
1.4.2Receipt of the UPS and visual inspection..................................................................................11
1.4.3Unpacking..................................................................................................................................12
1.4.4Nameplate and identification .....................................................................................................13
1.4.5Batteries And Storage................................................................................................................13
1.4.5.1Storage of battery ..............................................................................................................14
1.4.5.2Storage of UPS..................................................................................................................14
1.5SITE PLANNING AND POSITIONING .............................................................................................14
1.5.1PLANNING BEFORE THE INSTALLATION..............................................................................14
1.5.2POSITIONING OF UPS AND BATTERY CABINET..................................................................15
1.5.2.1Final Transport...................................................................................................................15
1.5.2.2Positioning .........................................................................................................................16
1.6ELECTRICAL INSTALLATION.........................................................................................................17
1.6.1PREPARATION FOR THE INPUT CABLING ...........................................................................18
1.6.1.1Earthing and Connection of Mains Supply ........................................................................18
1.6.1.2Single Input Feed...............................................................................................................19
1.6.1.3Dual Input Feed .................................................................................................................19
1.6.1.4Preparation for the Output Cabling....................................................................................19
1.6.1.5Connection of the Load......................................................................................................20
1.6.2Installation Checklist..................................................................................................................21

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 2/22 ABB
Printed in Switzerland – Modifications reserved
1.1 MECHANICAL CHARACTERISTICS MX-FRAMES AND MODULES
CONCEPTPOWER DPA CLASSIC DPA-50 TRIPLE DPA-150 UPGRADE DPA-250
MX - FRAMES
Configuration
accommodates: Max. 1 module
(30-50kVA) and
280 x 7/9Ah batteries
3 modules
(30-50kVA) and
240x 7/9Ah batteries
5 modules
(30-50kVA) and
no batteries
Max. Power connection kVA 50 150 250
Dimensions (WxHxD) mm 730x1650x800 730x1975x800 730x1975x800
Weight of Empty Frame
w/o modules and
w/o batteries kg 262 239 205
Weight of Frame
with modules and
w/o batteries kg 305 up to 309
(with 1 Module) 368 up to 379 (with 3 Modules) 420 up to 439
(with 5 Modules)
Colours Front door silver :RAL 9007 + black (inlets)
Side walls/top: Graphite grey (Pulverlacke No. 4222903402 serie 09RCCAT1)
MX- DPA MODULES
DPA 30 S2 DPA 40 S2 DPA 50 S2
Output Apparent Rated Power KVA 30 40 50
Output Active Rated Power KW 24 32 40
Output Power with Load PF=1 KVA / KW 24 / 24 32 / 32 40 /40
Variable Number of 12V Battery
Blocks No. 40-50 40-50 40-50
Dimensions (WxHxD) mm 663 x 225 x 720
Weight UPS Module kg 43.1 45.3 46.8
Colours Front : Graphite grey (Pulverlacke No. 4222903402
serie 09RCCAT1)

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 3/22 ABB
Printed in Switzerland – Modifications reserved
1.2 SAFETY INSTRUCTIONS
1.2.1 GENERAL SAFETY INTRODUCTION
The UPS System operates with mains, battery or bypass power. It contains components that carry high currents
and voltages. The properly installed UPS System is grounded to earth and IP 20 rated against electrical shock and
foreign objects. Installation and service have to be done by the manufacturer’s qualified technicians or their
authorized service partners.
WARNING!
OPERATIONS INSIDE THE UPS MUST BE PERFORMED BY A SERVICE
ENGINEER FROM THE MANUFACTURER OR FROM AN AGENT AUTHORIZED
BY THE MANUFACTURER.
This user manual contains guidelines to check delivery, installing and commissioning of the UPS and is intended
for people who plan the installation, install, commission and use or service the UPS. The reader is expected to
know the fundamentals of electricity, wiring, electrical components and electrical schematic symbols
NOTE!
CAREFULLY READ THE USER MANUAL BEFORE OPERATING OR WORKING
ON THE UPS.
1.2.2 DESCRIPITON OF SYMBOLS USED IN THIS MANUAL
WARNING!
THERE IS DANGER OF AN ELECTRICAL IMPACT
NOTE!
READ THE INFORMATION, IN ORDER TO AVOID EQUIPMENT DAMAGES
HEAVY!
THE WEIGHT OF A UPS MODULE CAN REACH 50KG, THEREFORE IT CAN BE
LIFTED ONLY BY 2 PERSON
!
!
!
KG

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 4/22 ABB
Printed in Switzerland – Modifications reserved
1.2.3 Symbols, Controls, and Indicators
PROTECTIVE GROUNDING TERMINAL
A terminal which must be connected to earth ground prior to making any
other connection to the equipment.
A terminal to which or from which a direct current or voltage may be
applied or supplied.
This symbol indicates the word “phase”.
ON The principal power switch is in the “ON” position
OFF The principal power switch is in the “OFF” position.
C CAUTION: REFER TO MANUAL
Refer to the Operator’s Manual for more information
DANGER: RISK OF ELECTRIC SHOCK
There is a risk of electric shock present, and you should observe
associated warnings. The UPS contains high voltages.

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 5/22 ABB
Printed in Switzerland – Modifications reserved
1.2.4 OPERATOR precautions
The only user operations permitted are:
Use of the LCD control panel (LCD Display) and of the Maintenance Bypass
Start up and shut down of the UPS of the user field (excluding the commissioning start up)
Operation of additional connectivity modules:
SNMP adapters and their software
Modem/GSM or Modem/Ethernet adapters and their software
Multidrop Kit for paralleling connectivity information between multi-frame configurations
The user must follow the precautions and only perform the described operations. Also in these measures the
operator of the USP System must adhere to the instructions in this manual. Any deviations from the instructions
could be dangerous to the user or cause accidental load loss.
THE MANUFACTURER DOES NOT TAKE ANY RESPONSIBILITY FOR DAMAGES CAUSED THROUGH
WRONG MANIPULATIONS OF THE UPS SYSTEM.
WARNING!
IT IS PROHIBITED TO REMOVE ANY SCREWS FROM THE UPS SYSTEM OR
FROM THE BATTERY CABINET. THERE IS A DANGER OF ELECTRICAL SHOCK.
WARNING!
HIGH FAULT CURRENTS (LEAKAGE CURRENTS):
BEFORE CONNECTING THE MAINS YOU MUST ENSURE THAT THERE IS A
PROPER EARTH CONNECTION!
WARNING!
THE USER MUST DISPLAY A WARNING SHIELD ON ALL PRIMARY UPS
CIRCUIT BREAKERS. THE SERVICE PERSONNEL HAS TO BE INFORMED
ABOUT DANGEROUS VOLTAGES. THE WARNING PANELS MUST CONTAIN
THE FOLLOWING TEXT: “ BEFORE STARTING WITH THE MAINTENANCE
WORK ON THE CIRCUIT BREAKERS MAKE SURE THE UPS IS ISOLATED

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 6/22 ABB
Printed in Switzerland – Modifications reserved
1.2.5 Environmental Considerations
The UPS must be installed according to the recommendations in this manual. To operate the UPS at peak
efficiency, your installation site should meet the environmental parameters outlined in this manual. Excessive
amount of dust in the operating environment of UPS may cause damage or lead to malfunction. The UPS should
be always protected from the outside weather and sunshine. If you intend to operate the system at an altitude
higher than 1000 meters, contact your local sales or service office for important information about high altitude
operation. The operating environment must meet the weight, airflow, size and clearance requirements specified in
the technical datasheet.
Under no circumstances the UPS should be installed in an airtight room, in the presence of flammable gases, or in
an environment exceeding the specification.
The basic environmental requirements of the UPS system are:
Ambient Temperature Range: 0 to +40˚C (32 – 104˚F)
Recommended Operating Range: +20 to +25˚C (68 – 77˚F)
Maximum Relative Humidity: 95% (non-condensing)
The UPS cabinet uses forced air cooling to regulate internal component temperature. Air inlets are in the bottom
sides and front of the cabinet, and outlets in the rear of the cabinet. You must allow clearance in back of the
cabinet for proper air circulation. Refer to 1.5.2.2 POSITIONING for clearance requirements.
1.2.6 Declaration of Safety conformity and CE marking
The product has the CE marking in compliance with the following European directives:
Low Voltage Directive: 2006/95/EC
EMC Directive: 2004/108/EC
Declaration of conformity with UPS harmonized standards and directives EN 62040-1-1 (Safety) and EN 62040-2
(EMC) are available on the web site of the manufacturer.
Product Standards Standards
Safety IEC/EN 62040-1 IEC/EN 60950-1
Electromagnetic Compatibility
EMC IEC/EN 62040-2
IEC/EN 61000-6-2
IEC/EN 61000-6-4
IEC/EN 61000-4-2
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
Performance IEC/EN 62040-3
1.2.7 Inquiries
Address inquiries about the UPS and battery cabinet to the local office or agent authorized by the manufacturer.
Please note the type code and the serial number of the equipment and contact your nearest agent authorized by
the manufacturer.
The Code and the serial no. are shown on the nameplate see 1.4.4 Nameplate and identification

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 7/22 ABB
Printed in Switzerland – Modifications reserved
1.3 SYSTEM DESCRIPTION
The product described in this manual is a transformerless Uninterruptible Power System (UPS). It is a true online,
continuous duty, double conversion, solid state, three-phase system, providing conditioned and uninterruptible AC
power to protect the customer’s load from all nine power failures.
1.3.1 GENERAL SYSTEM DESCRIPTION
The UPS’s are used to protect sensitive equipment and prevent loss of valuable electronic information, minimise
equipment downtime, and minimise the adverse effect on production equipment due to unexpected power
problems.
The UPS system continually monitors incoming electrical power and removes the surges, spikes, sags, and other
irregularities that are inherent in commercial utility power. Working with a building‘s electrical system, the UPS
system supplies clean, consistent power that sensitive electronic equipment requires for reliable operation. During
brownouts, blackouts, and other power interruptions, batteries provide emergency power to safeguard operation.
The UPS system is housed in single freestanding cabinets. The cabinets line up and match in style and colour,
and have safety shields behind the doors for hazardous voltage protection.
1.3.1.1 Feature : Unique “Hot Swappable” Modules
The unique Hot Swappable feature of the Modules indicates the ability to insert and extract the electronic/power
modules from a larger assembly while it is powered (hot). The hot swappable design allows live powered modules
to be attached to and removed from a powered set without causing disturbance to the operation of the load and
without need to go to bypass.
1.3.1.2 Feature : Advanced-Booster Technology
Traditional input THD filters are no longer needed with this UPS product. The build-in advanced booster
technology of UPS modules provides perfect sinusoidal input power quality at 0.99 input power factor with
harmonic content less than 3-4% THD(i). This leads to more reliable total system operation and savings in
generator and transformer sizing as losses in the windings are minimised.
Due to the active front booster, regulating each individual phase, the UPS is comparable to a clean resistor load
(unity) from the mains perspective. Thus, the high input power factor provides minimised cabling and fusing costs
due to no reactive power consumption. The low harmonic currents are due to high input power factor and provide
the benefits:
No additional losses in wires and cables
No extra heating of transformers and generators with shortened service life
No over sizing of generators
No false circuit breaker tripping and malfunction
No erratic operation of computers, telecommunication, monitors, electronic test equipment etc.
No Resonance with power factor correction capacitors

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 8/22 ABB
Printed in Switzerland – Modifications reserved
1.3.1.3 Feature : Flexible Battery Management (FBM)
The Flexible Battery Management (FBM) has been designed in all UPS products with the goal to avoid the
deterioration of battery age. The FBM – Key Features protect the battery from environmental negative impacts
(high temperature and false manipulations) and avoid deterioration of battery life by advanced management of
battery charging and preventive failure diagnostics. The implemented features result in benefits not only for the
end user, but also to the environment. The battery user will be required to replace his batteries less often. This
translates into financial and environmental benefits. Last but not least a well protected and managed battery is a
healthy battery and hence it enhance the overall availability of the UPS system.
The major benefits are:
AC-Ripple free battery charging due to DC-DC charger separated from the rectifier and inverter
Wide range of number of battery blocks (40-50 blocks of 12V)
UPS’S wide input voltage window tolerance extends the battery life due to less discharge cycles
Battery discharge protection caused by load jumps
Proactive battery protection from false manipulations and inadequate charging voltages
Proactive battery failure detection thanks to Advanced Battery Diagnosis (ABD) - Algorithm
User selectable battery tests
Optional temperature compensated charging to enhance battery life
Hence, the function of FBM system is to prolong the battery life considerably compared to traditional systems. In a
traditional online UPS the inverter also causes ripple-current to be fed to batteries causing corrosion.
1.3.1.4 Feature : DPA Technology - Decentralized Parallel Architecture
The UPS product features DPA paralleling technology that provides N+X redundancy without introducing a single-
point-of-failure. The products utilizing the DPA technology are completely autonomous be means of individual
Power Units, Bypasses, CPU’s, Control Panels and separate battery configuration for each single module.
The DPA technology makes it more reliable than traditional paralleling techniques. A parallel UPS system means
the linking together of two or more UPS units in parallel so that in the unlikely event one fails the other can
automatically take up the load. Traditionally a parallel redundancy configuration is achieved by having a random or
fixed master-slave relationship among the UPS units. This master logic gives out individual commands to all the
slaves units. Unfortunately this can lead to a single-point-of-failure for the whole system because if the master
logic or communication to slaves fails, and causes the whole UPS system to be in trouble.
The DPA technology was developed as a Multi-Master logic concept with separated independent regulation and
logic buses to allow parallel capacity system and to maintain the highest system availability. An industry leading
paralleling technology in its own right, the DPA technology enables you to set up a parallel redundant system
giving you 100% conditioned power at all times. Its unique decentralized design eliminates the system level single
point of failure inherent in traditional parallel UPS, and exponentially increases the reliability of the overall system.
DPA technology allows up to ten UPS modules to cover the same load in parallel and redundant configuration. No
vulnerable master logic is needed in this design. It provides automatic load sharing and module level redundancy
with nothing other than the power connecting to the Conceptpower DPATM S2 version of UPS modules.

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 9/22 ABB
Printed in Switzerland – Modifications reserved
1.3.2 Conceptpower DPATM S2 basic system configuration
The UPS system is housed in single freestanding cabinets. The cabinets line up and match in style and colour, and
have safety shields behind the doors for hazardous voltage protection.
The following basic UPS systems configuration are available:
Fig. 1) Fig. 2) Fig. 3)
UPS Frame
Type Module no.
Packed
Weight with
DPA 30 w/o
Batt. in kg
Packed
Weight with
DPA 40 w/o
Batt. in kg
Packed
Weight with
DPA 50 w/o
Batt. in kg
Packed
Dimension mm Unpacked Weight
with DPA 30 w/o
Batt. in kg
Unpacked
Weight with
DPA 40 w/o
Batt. in kg
Unpacked
Weight with
DPA 50 w/o
Batt. in kg
Unpacked
Dimension mm
Module 43.1 45.3 46.8 WxHxD 43.1 45.3 46.8 WxHxD
Fig. 1 CLASSIC-
DPA-50 1 328 330 332
890x1800x920 305 307 309 730x1650x800
Fig. 2 TRIPLE-
DPA-150
1 307 309 311
890x2120x920 282 284 286 730x1975x800
2 350 355 358 890x2120x920 325 330 333 730x1975x800
3 393 400 404 890x2120x920 368 375 379 730x1975x800
Fig. 3 UPGRADE-
DPA-250
1 273 275 277
890x2120x920 248 250 252 730x1975x800
2 316 321 324 890x2120x920 291 296 299 730x1975x800
3 359 366 370 890x2120x920 334 341 345 730x1975x800
4 402 411 417 890x2120x920 377 386 392 730x1975x800
5 446 457 464 890x2120x920 421 432 439 730x1975x800
1.3.3 Quality Standards and ups classification code
The Conceptpower DPATM S2 will provide your critical equipment with a steady and reliable power supply for many
years.
The unique and modular UPS Conceptpower DPATM S2 belongs to the newest generation of midrange 3phase
UPS-Systems. High reliability, low operating cost and excellent electrical performance are only some of the
highlights of this innovative UPS solution.
The criteria and methods implemented for the design and manufacture correspond to the most stringent quality
standards.
The manufacturer is certified successfully in every areas according to the model of the International Standard
ISO9001/EN 29001. The Certification of UPS with the operating performance according to the Norm
IEC 62 040-3 and VDE 0558 Part 530 is accomplished.
With it the UPS has the Classification Code VFl-SS-111.
Product Standards Standards
Safety IEC/EN 62040-1 IEC/EN 60950-1
Electromagnetic Compatibility
EMC IEC/EN 62040-2
IEC/EN 61000-6-2
IEC/EN 61000-6-4
IEC/EN 61000-4-2
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
Performance IEC/EN 62040-3

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 10/22 ABB
Printed in Switzerland – Modifications reserved
1.3.4 Single/Parallel-Modules operation
The Conceptpower DPATM S2 has unique paralleling features. We distinguish: Single or Parallel-Modules
A) Single-Module
CLASSIC DPA-50 TRIPLE DPA-150 UPGRADE DPA-250 1 single module
If a configuration consists of one single Module it is defined as a Single-Module Configuration even being in
different cabinets like CLASSIC DPA-50, TRIPLE DPA-150, UPGRADE DPA-250 with a single Module.
B) Parallel-Module:
TRIPLE DPA-150
A Parallel-Module is a Module that is operating in parallel with other equivalent Modules, but still within the same
cabinet (e.g. TRIPLE DPA-150) using the DPA technology
1.3.5 Single/Multi-Cabinet Configurations
Single-Cabinet Configuration:
A single-cabinet configuration means, that there are no cabinets operating in a chain.
Multi-Cabinet Configurations:
It is possible to parallel Conceptpower DPATM S2 CLASSIC DPA-50,
TRIPLE DPA-150, UPGRADE DPA-250 Cabinets into a Multi-Cabinet Configuration
(including total up to 30 Modules) in order to increase the number of paralleled Modules.
+ +

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 11/22 ABB
Printed in Switzerland – Modifications reserved
1.4 DELVERY - TRANSPORT - STORAGE
1.4.1 Introduction
This chapter contains all the necessary information for the correct unpacking, positioning, cabling and installation
of the UPS
The UPS and accessories are delivered on a specifically designed pallet that is easy to move with a forklift or a
pallet jack. Keep the UPS always in upright position and do not drop the equipment. Do not either stack the pallets
because of high-energy batteries involved and the heavy weight
NOTE!
IF THE UPS IS NOT IMMEDIATELY INST
A
LLED THE FOLLOWING GUIDELINES
MUST BE FOLLOWED:
TRANSPORT:
UPS CABINETS AND/OR BATTERY CABINET CAN FALL OVER. USE THE
SHIPPING BRACKETS ON THE REAR AND FRONT TO SECURE THE
CABINETS. DO NOT TILT THEM MORE THAN 10° FROM VERTICAL,
OTHERWISE CABINETS MAY TIP OVER.
POTENTIAL DANGERS:
- TILTING THE CABINET MIGHT DAMAGE THE SYSTEM AND THEREFORE
SHOULD NO LONGER BE CONNECTED TO THE MAINS.
- WEIGHT OF THE UPS SYSTEM COULD CAUSE SERIOUS INJURIES TO
PERSONS OR ANYTHING IN THE SURROUNDING AREA.
STORAGE:
- THE UPS SHOULD BE STORED IN THE ORIGINAL PACKING AND
SHIPPING CARTON
- THE RECOMMENDED STORING TEMPERATURE FOR THE UPS SYSTEM
AND BATTERIES IS BETWEEN +20 °C AND +25°C.
- THE UPS SYSTEM AND THE BATTERIE SETS MUST BE PROTECTED FROM
HUMIDITY < 95% (NON-CONDENSING)
1.4.2 Receipt of the UPS and visual inspection
Upon receiving the UPS, carefully examine the packing container and the UPS for any sign of physical damage.
The outside ’Tip&Tel’ ( "FRAGILE" and "ARROW") indicator should be intact if the equipment has been transported
in the upright position. In case of rupture or suspect inform immediately:
The carrier and
The manufacturer.
Ensure that the received UPS corresponds to the material indicated in the delivery note.
The packing container of the UPS protects it from mechanical and environmental damage. To increase its
protection the UPS is wrapped with a plastic sheet.
NOTE!
V
ISIBLE TRANSPORT D
A
MAGES MUST BE CLAIMED TO THE CARRIER
IMMEDIATELY AFTER RECEIPT !!
OTHER CLAIM FOR SHIPPING DAMAGE MUST BE FILED IMMEDIATELY TOO
AND THE CARRIER MUST BE INFORMED WITHIN 7 DAYS OF RECEIPT OF THE
EQUIPMENT. THE PACKING MATERIALS SHOULD BE STORED FOR FURTHER
INVESTIGATION.
!
!

Section-1
04-3008_S1_ABB_OPMCPDPA-S2_GB_121202 Page 12/22 ABB
Printed in Switzerland – Modifications reserved
1.4.3 Unpacking
Unpack the equipment by removing the packing and shipping materials. Make a visual inspection and check that
’Tip&Tel’ indicator ( "FRAGILE" and "ARROW") on the packing container is intact.
Perform the following steps to unpack the UPS equipment from the pallet and make sure that the floor surface is
solid and suitable for the wheeling and heavy weight:
1) Examine the UPS for any sign of damage. Notify your carrier or supplier immediately if damage is
apparent;
2) Remove the plastic cover from the UPS;
3) Remove pallet from the UPS;
!
KG HEAVY !
1)1)
2)
3)
3)