ABB PowerValue 11 RT User manual

PowerValue 11 RT
1-3 kVA B
1-3 kVA S
Quick guide

Quick guide | PowerValue 11 RT 1-3 kVA 1
1
2

2 PowerValue 11 RT 1-3 kVA | Quick guide
3
4

Quick guide | PowerValue 11 RT 1-3 kVA 3
5
6

4 PowerValue 11 RT 1-3 kVA | Quick guide
7

Quick guide | PowerValue 11 RT 1-3 kVA 5
8
9
10
11

6 PowerValue 11 RT 1-3 kVA | Quick guide

Quick guide | PowerValue 11 RT 1-3 kVA 7
PowerValue 11 RT 1-3 kVA
1en
es
da
zh
fr
fi
ru
nl
de
pt
cz
el
it
sv
pl
Quick guide 9
Kurzanleitung 21
Guide de référence rapide 33
Guida rapida 45
Guía rápida 57
Guia de consulta rápida 69
Pikaopas 81
Snabbinstruktion 93
Kvikguide 105
Rychlý průvodce 117
Краткое руководство 129
Skrócony podręcznik 141
速成指南 153
Σύντομος οδηγός 165
Beknopte installatiehandleiding 177

8 PowerValue 11 RT 1-3 kVA | Quick guide

Quick guide | PowerValue 11 RT 1-3 kVA 9
1en
PowerValue 11 RT 1-3 kVA
Quick guide
Safety instructions 10
Installation 15
Operation 17
Troubleshooting 19

10 PowerValue 11 RT 1-3 kVA | Quick guide
en
Safety instructions
Read carefully
Always follow the precautions and instructions described in this manual. Any
deviations from the instructions may result in electrical shock or cause accidental
load loss.
ABB DOES NOT TAKE ANY RESPONSIBILITY FOR DAMAGES CAUSED THROUGH INCORRECT
MANIPULATIONS OF THE UPS SYSTEM.
Safety notices
WARNING WARNING INDICATES THE PRESENCE OF A HAZARD WHICH COULD
RESULT IN SEVERE INJURY AND/OR SERIOUS DAMAGE TO THE SYSTEM.
CAUTION CAUTION INDICATES THE PRESENCE OF A HAZARD WHICH COULD
RESULT IN MINOR INJURY AND/OR DAMAGE TO THE PRODUCT.
NOTE NOTE INDICATES THE PRESENCE OF A HAZARD WHICH COULD LEAD TO
PROPERTY DAMAGE.
Safety symbols
SAFETY WARNING: THE SYMBOL IS USED TO ALERT THE USER TO WARNINGS,
CAUTIONS AND NOTES.
DANGER: THE SYMBOL IS USED TO ALERT THE USER TO THE OCCURRENCE
OF ELECTRICAL LIVE PARTS WITH HAZARDOUS VOLTAGES.

Quick guide | PowerValue 11 RT 1-3 kVA 11
1en
Batteries
DANGER WARNING
COMPONENTS INSIDE THE UPS ARE CONNECTED TO THE
BATTERY EVEN WHEN THE UPS IS DISCONNECTED FROM
THE MAINS POWER SUPPLY.
DANGER WARNING
DISCONNECT THE BATTERIES BEFORE CARRYING OUT ANY
KIND OF SERVICE AND/OR MAINTENANCE. VERIFY THAT NO
CURRENT IS PRESENT AND NO HAZARDOUS VOLTAGE
EXISTS IN THE CAPACITOR OR BUS CAPACITOR TERMINALS.
DANGER WARNING
A BATTERY CAN PRESENT A RISK OF ELECTRICAL SHOCK
AND HIGH SHORT CIRCUIT CURRENT. THE FOLLOWING
PRECAUTIONS MUST BE OBSERVED WHEN WORKING ON
BATTERIES:
• REMOVE WATCHES, RINGS OR OTHER METAL OBJECTS
• MAKE USE OF PROPER PPE (PERSONAL PROTECTION
EQUIPMENT) AS PER LOCAL POLICIES AND RULES
—WEAR FLAME/ARC RESISTANT WHOLE BODY
CLOTHING
—WEAR SUITABLE VOLTAGE RATED GLOVES
—USE SAFETY DIELECTRIC FOOTWEAR
—WEAR ARC FLASH FACE SHIELD
—USE VOLTAGE RATED TOOLS
• DO NOT LAY TOOLS OR METAL PARTS ON TOP OF
BATTERIES
• DISCONNECT THE CHARGING SOURCE PRIOR TO
CONNECTING OR DISCONNECTING BATTERY TERMINALS.
DANGER WARNING
THE BATTERY CIRCUIT IS NOT ISOLATED FROM THE INPUT
VOLTAGE. HAZARDOUS VOLTAGES MAY OCCUR BETWEEN
THE BATTERY TERMINALS AND THE GROUND. VERIFY THAT
NO VOLTAGE IS PRESENT BEFORE SERVICING.
WARNING
NEVER DISPOSE BATTERIES ON FIRE AS THEY MAY EXPLODE.

12 PowerValue 11 RT 1-3 kVA | Quick guide
en
WARNING
DO NOT OPEN OR MUTILATE THE BATTERIES.
WARNING
RELEASED ELECTROLYTE IS HARMFUL TO THE SKIN AND EYES.
CAUTION
REPLACE BATTERIES WITH THE SAME NUMBER AND SAME TYPE OF
BATTERIES.
Installation
DANGER WARNING
HIGH FAULT CURRENTS (LEAKAGE CURRENTS). BEFORE
CONNECTING THE MAINS ENSURE THAT the UPS IS
ELECTRICALLY GROUNDED!
DANGER WARNING
DO NOT REMOVE ANY SCREWS FROM THE UPS SYSTEM OR
FROM THE BATTERY CABINET: DANGER OF ELECTRICAL
SHOCK.
DANGER WARNING
WHEN OPENING OR REMOVING THE UPS-COVERS YOU ARE
EXPOSED TO DANGEROUS VOLTAGES.

Quick guide | PowerValue 11 RT 1-3 kVA 13
1en
WARNING
WATER CONDENSING MAY OCCUR IF THE UPS IS UNPACKED IN A VERY
LOW TEMPERATURE. IN THIS CASE IT IS NECESSARY TO WAIT UNTIL THE
UPS IS FULLY DRIED INSIDE OUT BEFORE PROCEEDING INSTALLATION
AND USE TO AVOID HAZARDS AND ELECTRIC SHOCK, WAIT UNTIL THE
UPS IS FULLY DRY BOTH INSIDE AND OUTSIDE BEFORE INSTALLING.
CAUTION
AN INTEGRAL SINGLE EMERGENCY SWITCHING DEVICE THAT PREVENTS
FURTHER SUPPLY TO THE LOAD BY THE UPS IN ANY MODE OF
OPERATION MUST BE PROVIDED IN THE BUILDING WIRING INSTALLATION.
CAUTION
DO NOT CONNECT EQUIPMENT THAT COULD OVERLOAD THE UPS
SYSTEM (FOR EXAMPLE LASER PRINTERS).
Operation
CAUTION
DO NOT OPERATE IN CASE OF PRESENCE OF WATER OR MOISTURE.
CAUTION
DO NOT DISCONNECT THE MAINS CABLE FROM THE UPS OR THE
BUILDING WIRING SOCKET DURING OPERATION AS THIS REMOVES THE
GROUND FROM THE UPS AND ALL CONNECTED LOADS.
CAUTION
SWITCH OFF THE CONNECTED LOADS BEFORE TURNING ON THE UPS.
THEN SWITCH ON THE LOADS ONE BY ONE AFTER THE UPS IS TURNED
ON. SWITCH OFF ALL OF THE CONNECTED LOADS BEFORE TURNING OFF
THE UPS.
CAUTION
REPLACE FUSES ONLY BY DEVICES OF THE SAME TYPE AND OF THE
SAME AMPERAGE TO AVOID FIRE HAZARDS.

14 PowerValue 11 RT 1-3 kVA | Quick guide
en
CAUTION
INDISCRIMINATE OPERATION OF SWITCHES MAY CAUSE OUTPUT LOSS OR
DAMAGE TO EQUIPMENT.
NOTE
PRESS THE OFF BUTTON TO FULLY DISCONNECT THE UPS. WAIT UNTIL
THE UPS IS ON BYPASS OR ON STAND-BY MODE BEFORE
DISCONNECTING IT FROM THE MAINS.

Quick guide | PowerValue 11 RT 1-3 kVA 15
1en
Installation
Planning before installation
Install the unit to a position where any danger to the UPS is minimized to ensure a
long service life:
• Install the UPS indoors.
• Leave 25 cm of space on each side of the cabinet to enable cooling airflow and
ensure that the circulation of air to the ventilation slits is not obstructed.
• Avoid excessively high temperature and excessive moisture.
• Make sure that the surface is solid and flat.
Rack mount installation – requires rack mounting kit, to be purchased
separately
PowerValue 11 RT can be installed in a 19-inch rack. Both the UPS and the external
battery enclosure are 2U in height.
• Align the rack mounting ears on the side of the UPS and tighten the screws.
(Fig.1)
• Assemble the rack rails with the rack-mounting kit. (Fig.2)
• Slide the UPS into the rack rail and lock it into the structure. (Fig.3)
• Tighten the screws and then proceed with wiring of the UPS .
Tower installation
• Place the UPS in a vertical position with the front panel screws orientated as in
Fig.4
• Place the two stands on a horizontal surface (Fig.4)
• Place the UPS carefully on the UPS stands (Fig.4-5)
• Pull out the LCD box. Rotate it 90º clockwise and then push it back into the front
panel (Fig.6-7)

16 PowerValue 11 RT 1-3 kVA | Quick guide
en
Electrical connections
• PowerValue 11 RT 1 kVA B, 1 kVA S, 2 kVA B (see Fig.8)
• PowerValue 11 RT 2 kVA S (see Fig.9)
• PowerValue 11 RT 3 kVA B (see Fig.10)
• PowerValue 11 RT 3 kVA S (see Fig.11)
Legend
1AC output
2EPO / Dry contact input port
3USB port
4AC input
5Dry contact output port
6SNMP/ AS400 slot
7RS232
8HI-POT screw
9GND contact

Quick guide | PowerValue 11 RT 1-3 kVA 17
1en
Operation
You can operate the UPS through the user-friendly display (see chapter 4 of the user
manual for a full list of possible operations).
Power on/off
Scroll up Scroll down
Select / Edit
UPS start-up
To start up the UPS with mains supply:
1. Check that all cables are connected correctly and well-fixed mechanically.
2. Connect the UPS to the power supply.
3. Keep the power-on button pressed for longer than 1 second. The alarm buzzer
will sound for 1 second and the UPS will start up.
4. After a few seconds, the UPS goes to online-mode. If the mains power is
abnormal, the UPS will transfer to battery-mode without interruption in the output
of the UPS.

18 PowerValue 11 RT 1-3 kVA | Quick guide
en
To start up the UPS without mains supply (cold start):
1. Check that all cables are connected correctly and well-fixed mechanically.
2. Press the power-on button. The UPS will perform a self-test and display the
status screen.
3. Keep the power-on button pressed for longer than 1 second. The alarm buzzer
sounds and the UPS will start up.
4. After a few seconds, the UPS transfers to battery-mode. When the UPS is
supplied with power from the mains, the UPS transfers to online-mode without
interruption in the output of the UPS.
UPS Shutdown
To shut down the UPS with mains supply:
1. If the UPS is working on bypass-mode, go to step 3.
2. If the UPS is on online-mode, keep the power-on button pressed for more than 3
seconds. The alarm buzzer will sound and the UPS will transfer to bypass-mode.
Note that the output is still energized.
3. Disconnect the mains power supply. The display will shut down and the output
voltage will be removed from the UPS output terminal.
4. In case bypass has been disabled through the Settings menu, keep the power-
on button pressed for more than 3 seconds to shut down the UPS. The unit will
transfer from online to stand-by mode. Disconnect the input power cable and the
display will shut down.
To shut down the UPS without mains supply:
1. To power off the UPS, keep the power on/off button pressed for more than 3
seconds. The alarm buzzer will sound for 3 seconds and the output power will be
immediately cut-off.
2. The display will shut down and the output voltage will be removed from the UPS
output terminal.