ADF Web HD67155-A1 User manual

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 1 di 37
User Manual
Revision 1.100
English
CAN / SNMP Agent - Converter
(Order Code: HD67155-A1, HD67155-B2)
for Website information:
www.adfweb.com? roduct=HD67155
for rice information:
www.adfweb.com? rice=HD67155-A1
www.adfweb.com? rice=HD67155-B2
Benefits and Main Features:
Very easy to configure
Electrical isolation
Temperature range: -40°C/85°C (-40°F/185°F)
For others SNM Agent products, see also the following links:
Converter SNMP to
www.adfweb.com? roduct=HD67039 (DMX)
www.adfweb.com? roduct=HD67092 (M-Bus Wireless)
www.adfweb.com? roduct=HD67156 (CANo en)
www.adfweb.com? roduct=HD67159 (EtherNet/IP)
www.adfweb.com? roduct=HD67160 (DeviceNet Master)
www.adfweb.com? roduct=HD67161 (DeviceNet Slave)
www.adfweb.com? roduct=HD67162 (J1939)
www.adfweb.com? roduct=HD67163 (M-Bus Master)
www.adfweb.com? roduct=HD67164 (Modbus Master)
www.adfweb.com? roduct=HD67165 (Modbus Slave)
www.adfweb.com? roduct=HD67166 (Modbus TCP Master)
www.adfweb.com? roduct=HD67167 (Modbus TCP Slave)
www.adfweb.com? roduct=HD67168 (PROFIBUS Master)
www.adfweb.com? roduct=HD67169 (PROFIBUS Slave)
www.adfweb.com? roduct=HD67613 (PROFINET)
www.adfweb.com? roduct=HD67693 (BACnet Slave)
www.adfweb.com? roduct=HD67726 (BACnet Master)
www.adfweb.com? roduct=HD67820 (KNX)
www.adfweb.com? roduct=HD67850 (DALI)
Do you have an your customer protocol?
www.adfweb.com? roduct=HD67003
Do you need to choose a device? do you want help?
www.adfweb.com?Cmd=helpme
User Manual

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 2 di 37
INDEX:
age
INDEX 2
U DATED DOCUMENTATION 2
REVISION LIST 2
WARNING 2
TRADEMARKS 2
SECURITY ALERT 3
EXAM LE OF CONNECTION 4
CONNECTION SCHEME 5
CHARACTERISTICS 7
CONFIGURATION 7
OWER SU LY 8
FUNCTION MODES 9
LEDS 10
SNM 11
CAN 12
USE OF COM OSITOR SW67155 13
NEW ROJECT / O EN ROJECT 14
SOFTWARE O TIONS 15
SET COMMUNICATION 17
RECEIVE FRAMES 18
INFO RECEIVE 19
SEND FRAMES 20
INFO SEND 21
SET SNM ACCESS 22
U DATE DEVICE 24
SNM COMMUNICATION 26
SENDING ASYNCHRONOUS CAN MESSAGES
FROM ETHERNET
31
MECHANICAL DIMENSIONS 33
ORDERING INFORMATIONS 35
ACCESSORIES 35
DISCLAIMER 36
OTHER REGULATIONS AND STANDARDS 36
WARRANTIES AND TECHNICAL SU ORT 37
RETURN OLICY 37
UPDATED DOCUMENTATION:
Dear customer, we thank you for your attention and we remind you that
you need to check that the following document is:
Updated
Related to the product you own
To obtain the most recently updated document, note the “document code”
that appears at the top right-hand corner of each page of this document.
With this “Document Code” go to web page www.adfweb.com/download/
and search for the corresponding code on the page. Click on the proper
“Document Code” and download the updates.
REVISION LIST:
WARNING:
ADFweb.com reserves the right to change information in this manual about
our product without warning.
ADFweb.com is not responsible for any error this manual may contain.
TRADEMARKS:
All trademarks mentioned in this document belong to their respective
owners.
Revision Date Author Cha ter Descri tion
1.000 05/01/2015 Ff All First Release
1.100 01/02/2017 Ff All New software version

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 3 di 37
SECURITY ALERT:
G ENERAL I NFORMATION
To ensure safe operation, the device must be operated according to the instructions in the manual. When using the device, legal and
safety regulation are required for each individual application. The same applies also when using accessories.
I NTENDED U SE
Machines and systems must be designed so the faulty conditions do not lead to a dangerous situation for the operator (i.e.
independent limit switches, mechanical interlocks, etc.).
Q UALIFIED P ERSONNEL
The device can be used only by qualified personnel, strictly in accordance with the specifications.
Qualified personnel are persons who are familiar with the installation, assembly, commissioning and operation of this equipment and
who have appropriate qualifications for their job.
R ESIDUAL R ISKS
The device is state-of-the-art and is safe. The instruments can represent a potential hazard if they are inappropriately installed and
operated by untrained personnel. These instructions refer to residual risks with the following symbol:
This symbol indicates that non-observance of the safety instructions is a danger for people that could lead to serious injury or
death and / or the possibility of damage.
CE CONFORMITY
The declaration is made by our company. You can send an email to [email protected]om or give us a call if you need it.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 4 di 37
EXAMPLE OF CONNECTION:

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 5 di 37
CONNECTION SCHEME:
Figure 1a: Connection scheme for HD67155-A1

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 6 di 37
Figure 1b: Connection scheme for HD67155-B2

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 7 di 37
CHARACTERISTICS:
The HD67155-A1 and HD67155-B2 is a CAN / SNM Agent - Converter.
It has the following characteristics:
Up to 1024 bytes in reading and 1024 bytes in writing;
Triple isolation between CAN - ower Supply, CAN - Ethernet, ower Supply - Ethernet.
Two-directional information between CAN bus and SNM bus;
Mountable on 35mm Rail DIN;
Wide power supply input range: 8…24V AC or 12…35V DC;
Wide temperature range: -40°C / 85°C [-40°F / +185°F].
CONFIGURATION:
You need Compositor SW67155 software on your C in order to perform the following:
Define the parameter of SNM line;
Define the parameter of CAN line;
Define the CAN frames that the converter can accept;
Define the CAN frames that the converter sends trough the CAN line;
Define the map of CAN byte that must be written in the SNM array;
Define the map of which SNM bytes must be written in CAN frames;
Update the device.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 8 di 37
POWER SUPPLY:
The devices can be powered at 8…24V AC and 12…35V DC. For more details see the two tables below.
VAC
VDC
Vmin Vmax Vmin Vmax
8V 24V 12V 35V
Consumption at 24V DC:
Device Consum tion [W/VA]
HD67155-A1 3.5
HD67155-B2 3.5
HD67155
-
A1
Caution: Not reverse the olarity ower
HD67
15
5
-
B2

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 9 di 37
FUNCTION MODES:
The device has got two functions mode depending of the position of the ‘Dip2 of Dip-Switch A’:
The first, with ‘Dip2 of Dip-Switch A’ at “OFF” position, is used for the normal working of the device.
The second, with ‘Dip2 of Dip-Switch A’ at “ON” position, is used for upload the roject and/or Firmware.
For the operations to follow for the updating, see ‘U DATE DEVICE’ section.
According to the functioning mode, the LEDs will have specifics functions, see ‘LEDS’ section.
Warning:
Dip1 of ‘Dip-Switch A’ must be at ON position for working even if the Ethernet cable isn’t inserted.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 10 di 37
LEDS:
The devices has got four (five for HD67515-B2) LEDs that are used to give information of the functioning status.
The various meanings of the LEDs are described in the table below.
LED Normal Mode Boot Mode
1: Device State Blinks slowly (~1Hz) Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
2: Ethernet Link ON: Ethernet cable connected
OFF: Ethernet cable disconnected
ON: Ethernet cable connected
OFF: Ethernet cable disconnected
3: Ethernet Communication Blinks when SNM frames are received Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
4: CAN Communication Blinks when CAN frames are received Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
5: Not used ( resent only on
HD67155-B2) OFF Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 11 di 37
SNMP:
The SNM connection must be made using Connector5 of HD67155-A1/B2 with at least a Category 5E cable. The maximum length of the
cable should not exceed 100m. The cable has to conform to the T568 norms relative to connections in cat.5 up to 100 Mbps. To connect the
device to an Hub/Switch is recommended the use of a straight cable, to connect the device to a C/other is recommended the use of a cross
cable.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 12 di 37
CAN:
For terminate the CAN line with a 120Ω resistor it is necessary that the Dip1 of ‘Dip-Switch C’ is at ON position.
Cable characteristics:
DC arameter: Impedance 70 Ohm/m
AC arameters: Impedance 120 Ohm/m
Delay 5 ns/m
Length Baud Rate [b s] Length MAX [m]
10 K 5000
20 K 2500
50 K 1000
100 K 650
125 K 500
250 K 250
500 K 100
800 K 50
1000 K 25

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 13 di 37
USE OF COMPOSITOR SW67155:
To configure the Converter, use the available software that runs with Windows called SW67155. It is downloadable on the site
www.adfweb.com and its operation is described in this document. (This manual is referenced to the last version of the software present on
our web site). The software works with MSWindows (X , Vista, Seven, 8, 10; 32/64bit).
When launching the SW67155, the window below appears (Fig. 2).
Note:
It is necessary to have installed .Net Framework 4.
Figure 2: Main window for SW67155

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 14 di 37
NEW CONFIGURATION / OPEN CONFIGURATION:
The “New Configuration” button creates the folder which contains the entire device’s configuration.
A device’s configuration can also be imported or exported:
To clone the configurations of a rogrammable “CAN / SNM Agent - Converter” in
order to configure another device in the same manner, it is necessary to maintain the
folder and all its contents;
To clone a project in order to obtain a different version of the project, it is sufficient to
duplicate the project folder with another name and open the new folder with the
button “O en Configuration”.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 15 di 37
SOFTWARE OPTIONS:
By pressing the “Settings” ( ) button there is the possibility to change the language of the software and check the updatings for the
compositor.
In the section “Language” it is possible to change the language of the
software.
In the section “Connection Options”, it is possible to check if there are some
updatings of the software compositor in ADFweb.com website.
Checking the option “Check Software U date at Start of Program”, the
SW67155 check automatically if there are updatings when it is launched.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 16 di 37
In the section “Software Settings”, it is possible to enable/disable some
keyboard’s commands for an easier navigation inside the tables contained in
the different sections of the software.

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 17 di 37
SET COMMUNICATION:
This section define the fundamental communication parameters of two buses, SNM and CAN.
By ressing the “Set Communication” button from the main window for SW67155 (Fig. 2) the
window “Set Communication” appears (Fig. 3).
The window is divided in two sections, one for the SNM and the other for the CAN.
The means of the fields for “SNM ” are:
In the fields “IP ADDRESS” the I address of the converter is defined;
In the fields “SUBNET Mask” the SubNet Mask of the converter is defined;
In the fields “GATEWAY” the default gateway of the network is defined. This feature can be
enabled or disabled pressing the Check Box field. This feature is used for going out of the net;
In the field “Tunneling Port” the port to use for the “Tunneling mode” is defined (see page 31
for more details);
In the field "Send Back CAN messages" it is possible to enable the transmission of CAN
messages in a transparent mode;
If the option "Re ly on the Tunneling Port" is checked, the CAN messages are sent to the
Tunneling ort (applicable only if the "Send back CAN messages" is enabled);
In the field "SNMP Name of Station" the name for SNM Agent station is defined;
In the field "Contact" the contact for SNM Agent station is defined;
In the field "Location" the location for SNM Agent station is defined.
The means of the fields for the “CAN” section are:
In the field “Baudrate” the CAN baudrate is defined.
Figure 3: “Set Communication” window

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 18 di 37
RECEIVE FRAMES:
By pressing the “Receive Frames” button from the main window for SW67155 (Fig. 2) the “Receive CAN Frames” window appears (Fig. 4).
The COB inserted in this table contains the Output data of SNM . These frames are accepted by the Converter.
The data of the columns have the following meanings:
In the field “Cob-ID” the COB-ID of the CAN frame is defined;
In the field “Ty e” the type of CAN message is defined (2.0A (11 bits) or 2.0B (29 bits));
In the field “Dimension” the number of data bytes of the message (from 1 to 8) is defined;
In the field “TimeOut” the time (in ms) of the timeout of the data is defined. If a CAN frame is not received in this time, all the data
of the CAN frame will be set to zero. It is possible to disable this function by setting this field to ‘0’;
In the field “Mnemonic” a brief description is defined.
Figure 4: “Receive
CAN
Frames” window

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 19 di 37
INFO RECEIVE:
By pressing the “Info Receive” button from the main window for SW67155 (Fig. 2) the “Receive CAN Frames Info” window appears (Fig.
5):
In the column “COB ID” there are the COB-IDs listed in the “Receive Frames” section;
In the fields “Bytes” the bytes of the internal array of the converter where mapping the data from CAN are defined.
Figure 5: “Receive
CAN
Frames Info” window

Industrial Electronic Devices
ADFweb.com Srl – IT31010 – Mareno – Treviso INFO: www.adfweb.com hone +39.0438.30.91.31
User Manual
CAN / SNMP Agent
Document code: MN67155_ENG Revision 1.100 agina 20 di 37
SEND FRAMES:
By pressing the “Send Frames” button from the main window for SW67155 (Fig. 2) the “Send CAN frames” window appears (Fig. 6).
The COB inserted in this table contains the Input data of SNM . These frames are sent by the Converter.
The data of the columns have the following meanings:
In the field “Cob-ID” the COB-ID of the CAN frame is defined;
In the field “Ty e” the type of CAN message sent is defined (‘2.0A (11bits)’ or ‘2.0B (29bits)’);
In the field “Dimension” the number of bytes of the CAN frame (from 1 to 8) is defined;
In the field “Send Frame Ty e” the transmission type of the CAN frame is defined. There are two options:
o“On Data Change”: the frame is sent when the data changes;
o“On Times”: the frame is sent cyclically;
In the field “Timer Send” the delay (in ms) between two CAN frames is defined (if the option “On Timer” is checked);
In the field “Mnemonic” a brief description is defined.
Figure 6
: “
Send CAN Frames
” window