ADF Web HD67647-A1 User manual

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 1 of 23
User Manual
Revision 1.000
English
EtherNet/IP Master / DeviceNet Slave -
Converter
(Order Code: HD67647-A1 )
For Website information:
www.adfweb.com? roduct=HD67647
For rice information:
www.adfweb.com? rice=HD67647-A1
Benefits and Main Features:
Very easy to configure
Triple Electrical isolation
Temperature range: -40°C/+85°C (-40°F/+185°F)
For other EtherNet/I Master Slave products see also the following link:
Converter EtherNet/IP Master to
www.adfweb.com? roduct=HD67B38 (OPC A Server)
www.adfweb.com? roduct=HD67D24 (LoRaWAN)
www.adfweb.com? roduct=HD67E26 (EtherCAT)
www.adfweb.com? roduct=HD67158 (SNMP Agent)
www.adfweb.com? roduct=HD67643 (PROFIB S Slave)
www.adfweb.com? roduct=HD67645 (CAN)
www.adfweb.com? roduct=HD67646 (CANopen)
www.adfweb.com? roduct=HD67647 (DeviceNet Slave)
www.adfweb.com? roduct=HD67661 (PROFINET)
www.adfweb.com? roduct=HD67665 (Modbus TCP Slave)
www.adfweb.com? roduct=HD67667 (Serial)
www.adfweb.com? roduct=HD67668 (Ethernet)
www.adfweb.com? roduct=HD67669 (Modbus Slave)
www.adfweb.com? roduct=HD67689 (BACnet Slave)
www.adfweb.com? roduct=HD67743 (IEC 61850 Server)
www.adfweb.com? roduct=HD67806 (KNX)
www.adfweb.com? roduct=HD67955 (MQTT)
www.adfweb.com? roduct=HD67973 (IO-Link Slave)
User Manual

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 2 of 23
INDEX:
age
INDEX 2
U DATED DOCUMENTATION 2
REVISION LIST 2
WARNING 2
TRADEMARKS 2
SECURITY ALERT 3
EXAM LE OF CONNECTION 4
CONNECTION SCHEME 5
CHARACTERISTICS 6
CONFIGURATION 6
OWER SU LY 7
FUNCTION MODES 8
LEDS 9
CAN 10
ETHERNET 11
USE OF COM OSITOR SW67647 12
NEW CONFIGURATION / O EN CONFIGURATION 13
SOFTWARE O TIONS 14
SET COMMUNICATION 16
ETHERNET/I SET ACCESS 17
U DATE DEVICE 18
MECHANICAL DIMENSIONS 20
ORDERING INFORMATIONS 21
ACCESSORIES 21
DISCLAIMER 22
OTHERS REGULATIONS AND STANDARDS 22
WARRANTIES AND TECHNICAL SU ORT 23
RETURN OLICY 23
PDATED DOC MENTATION:
Dear customer, we thank you for your attention and we remind you that
you need to check that the following document is:
Updated
Related to the product you own
To obtain the most recently updated document, note the “document code”
that appears at the top right-hand corner of each page of this document.
With this “Document Code” go to web page www.adfweb.com/download/
and search for the corresponding code on the page. Click on the proper
“Document Code” and download the updates.
REVISION LIST:
WARNING:
ADFweb.com reserves the right to change information in this manual about
our product without warning.
ADFweb.com is not responsible for any error this manual may contain.
TRADEMARKS:
All trademarks mentioned in this document belong to their respective
owners.
Revision Date Author Chapter Description
1.000 18/09/2020 Ff All First Release

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 3 of 23
SEC RITY ALERT:
G ENERAL I NFORMATION
To ensure safe operation, the device must be operated according to the instructions in the manual. When using the device, legal and
safety regulation are required for each individual application. The same applies also when using accessories.
I NTENDED SE
Machines and systems must be designed so the faulty conditions do not lead to a dangerous situation for the operator (i.e.
independent limit switches, mechanical interlocks, etc.).
Q ALIFIED P ERSONNEL
The device can be used only by qualified personnel, strictly in accordance with the specifications.
Qualified personnel are persons who are familiar with the installation, assembly, commissioning and operation of this equipment and
who have appropriate qualifications for their job.
R ESID AL R ISKS
The device is state-of-the-art and is safe. The instruments can represent a potential hazard if they are inappropriately installed and
operated by untrained personnel. These instructions refer to residual risks with the following symbol:
This symbol indicates that non-observance of the safety instructions is a danger for people that could lead to serious injury or
death and / or the possibility of damage.
CE CONFORMITY
The declaration is made by our company. You can send an email to [email protected]om or give us a call if you need it.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 4 of 23
EXAMPLE OF CONNECTION:

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 5 of 23
CONNECTION SCHEME:
Figure 1: Connection scheme for HD67647-A1

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 6 of 23
CHARACTERISTICS:
The HD67647-A1 are EtherNet/I / DeviceNet - Converters.
It allows for the following characteristics:
Isolation between EtherNet/I – DeviceNet – ower Supply;
Two-directional information between EtherNet/I bus and DeviceNet bus;
Mountable on 35mm Rail DIN;
Wide power supply input range: 8…24V AC or 12…35V DC;
Wide temperature range: -40°C / 85°C [-40°F / +185°F].
CONFIG RATION:
You need Compositor SW67647 software on your C in order to perform the following:
Define the parameters of EtherNet/I line;
Define the parameters of DeviceNet line;
Define the list of EtherNet/I slaves connected to the converter;
Update the device.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 7 of 23
POWER S PPLY:
The devices can be powered at 8…24V AC and 12…35V DC. For more details see the two tables below.
VAC
VDC
Vmin Vmax Vmin Vmax
8V 24V 12V 35V
Consumption at 24V DC:
Device Consumption [W/VA]
HD67647-A1 3.5
HD67647-A1
Caution:
Do n
ot reverse the polarity power

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 8 of 23
F NCTION MODES:
The device has got two function modes depending on the position of the ‘Dip1 of Dip-Switch A’:
The first, with ‘Dip1 of Dip-Switch A’ at “OFF” position, is used for the normal working of the device.
The second, with ‘Dip1 of Dip-Switch A’ at “ON” position, is used for uploading the roject and/or Firmware.
For the operations to follow for the updating, see ‘U DATE DEVICE’ section.
According to the functioning mode, the LEDs will have specific functions, see ‘LEDS’ section.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 9 of 23
LEDS:
The device has got seven LEDs that are used to give information about the functioning status.
The various meanings of the LEDs are described in the table below.
LED Normal Mode Boot Mode
1: ON (green) ON: Device powered
OFF: Device not powered
ON: Device powered
OFF: Device not powered
2: CAN comm. (green) It blinks when a CAN message is received Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
3: Device State (green) Blinks slowly (~1Hz) Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
4: Ethernet comm. (green) It blinks when EtherNet/I communication is running Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
5: Ethernet1 link (green) ON: Ethernet cable connected
OFF: Ethernet cable disconnected
ON: Ethernet cable connected
OFF: Ethernet cable disconnected
6: Ethernet2 link (green) ON: Ethernet cable connected
OFF: Ethernet cable disconnected
ON: Ethernet cable connected
OFF: Ethernet cable disconnected

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 10 of 23
CAN:
For terminating the CAN line with a 120Ω resistor it is necessary that the Dip1 of ‘Dip-Switch C’ is at ON position.
Cable characteristics:
DC parameter: Impedance 70 Ohm/m
AC parameters: Impedance 120 Ohm/m
Delay 5 ns/m
Length Baud Rate [bps] Length MAX [m]
10 K 5000
20 K 2500
50 K 1000
100 K 650
125 K 500
250 K 250
500 K 100
800 K 50
1000 K 25

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 11 of 23
ETHERNET:
The updating of the converter must be made using Connector3 and Connector4 of the HD67647-A1 with at least a Category 5E cable. The
maximum length of the cable should not exceed 100m. The cable has to conform to the T568 norms relative to connections in cat.5 up to
100 Mbps. To connect the device to an Hub/Switch is recommended the use of a straight cable, to connect the device to a C/ LC/other is
recommended the use of a cross cable.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 12 of 23
SE OF COMPOSITOR SW67647:
To configure the Converter, use the available software that runs with Windows called SW67647. It is downloadable on the site
www.adfweb.com and its operation is described in this document. ( his manual is referenced to the last version of the software present on
our web site). The software works with MSWindows (X , Vista, Seven, 8, 10; 32/64bit).
When launching the SW67647, the window below appears (Fig. 2).
Note:
It is necessary to have installed .Net Framework 4.
Figure 2: Main window for SW67
647

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 13 of 23
NEW CONFIG RATION / OPEN CONFIG RATION:
The “New Configuration” button creates the folder which contains the entire device’s configuration.
A device’s configuration can also be imported or exported:
To clone the configurations of a programmable “EtherNet/I Master / DeviceNet Slave
- Converter” in order to configure another device in the same manner, it is necessary
to maintain the folder and all its contents;
To clone a project in order to obtain a different version of the project, it is sufficient to
duplicate the project folder with another name and open the new folder with the
button “Open Configuration”.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 14 of 23
SOFTWARE OPTIONS:
By pressing the “Settings” ( ) button there is the possibility to change the language of the software and check the updatings for the
compositor.
In the section “Language” it is possible to change the language of the
software.
In the section “Connection Options”, it is possible to check if there are some
updatings of the software compositor in ADFweb.com website.
Checking the option “Check Software pdate at Start of Program”, the
SW67647 checks automatically if there are updatings when it is launched.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 15 of 23
In the section “Software Settings”, it is possible to enable/disable some
keyboard’s commands for an easier navigation inside the tables contained in
the different sections of the software.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 16 of 23
SET COMM NICATION:
This section define the fundamental communication parameters of two buses,
EtherNet/I and DeviceNet.
By ressing the “Set Communication” button from the main window for SW67647
(Fig. 2) the window “Set Communication” appears (Fig. 3).
The means of the fields for the “DeviceNet Slave” section are:
In the field “ID Device” the address for the DeviceNet Master is defined;
In the field “Baudrate” the velocity of the DeviceNet Slave bus is defined:
In the field “Number Byte IN” the number input bytes of DeviceNet Master is
defined (max 455 bytes);
In the field “Number Byte O T” the number output bytes of DeviceNet Master
is defined (max 455 bytes).
The means of the fields for “EtherNet/I Master” are:
In the fields “IP ADDRESS” the I address for EtherNet/I side of the converter
is defined;
In the fields “S BNET Mask” the SubNet Mask for EtherNet/I side of the
converter is defined;
In the fields “GATEWAY” the default gateway of the net is defined. This feature
can be enabled or disabled pressing the Check Box field. This feature is used for
going out of the net;
In the field “Port” the port used for EtherNet/I communication is defined. The
port has a fixed value of 44818.
Figure 3: “Set Communication” window

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 17 of 23
Figure 4: “Set EtherNet/IP Slaves Access” window
ETHERNET/IP ACCESS:
By ressing the “EtherNet/IP Access” button from the main window for SW67647 (Fig. 2) the window “Set EtherNet/I Master Access”
appears (Fig. 4).
This section is used to define the list of the EtherNet/I Slaves to read/write with the DeviceNet Master.
The means of the fields are:
If the field “Enable” is checked, the polling to the EtherNet/I Slave is enabled;
In the field “IP Address” the I Address of the EtherNet/I Slave is defined;
In the field “Start Input” the starting Input byte of the EtherNet/I Slave to map on DeviceNet side is defined;
In the field “Num Input” the number of consecutive Input byte to map on DeviceNet side is defined;
In the field “Start Output” the starting Output byte of the EtherNet/I Slave to write from DeviceNet side is defined;
In the field “Num Output” the number of consecutive Output byte to write from DeviceNet side is defined;
In the field “Time Poll” the polling time in ms is defined;
In the field “Instance T > O” the instance of the assembly for the Target to Originator data direction is defined;
In the field “Conn. Point T > O” the connection point of the assembly for the Target to Originator data direction is defined;
In the field “Instance O > T” the instance of the assembly for the Originator to Target data direction is defined;
In the field “Conn. Point O > T” the connection point of the assembly for the Originator to Target data direction is defined;
In the field “Dim Header T > O” the dimension of the header for the Target to Originator data direction is defined;
In the field “Dim Header O > T” the dimension of the header for the Originator to Target data direction is defined;
In the field “Mnemonic” a brief description is defined.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 18 of 23
PDATE DEVICE:
By pressing the “ pdate Device” button, it is possible to load the created
Configuration into the device; and also the Firmware, if necessary. This by using the
Ethernet port.
If you don’t know the actual I address of the device you have to use this procedure:
Turn OFF the Device;
ut Dip1 of ‘Dip-Switch A’ in ON position;
Turn ON the device
Connect the Ethernet cable;
Insert the I “192.168.2.205”;
Select which operations you want to do;
ress the “Execute update firmware” button to start the upload;
When all the operations are “OK” turn OFF the Device;
ut Dip1 of ‘Dip-Switch A’ in OFF position;
Turn ON the device.
If you know the actual I address of the device, you have to use this procedure:
Turn ON the Device with the Ethernet cable inserted;
Insert the actual I of the Converter;
Select which operations you want to do;
ress the “Execute update firmware” button to start the upload;
When all the operations are “OK” the device automatically goes at Normal Mode.
At this point the configuration/firmware on the device is correctly updated.
Figure 5: “Update device” windows

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 19 of 23
Note:
When you receive the device, for the first time, you also have to update the Firmware in the HD67647 device.
Warning:
If Fig. 6 appears when you try to do the Update try these points before seeking
assistance:
Try to repeat the operations for the updating;
Try with another C;
Try to restart the C;
Check the LAN settings;
If you are using the program inside a Virtual Machine, try to use in the main
Operating System;
If you are using Windows Seven, Vista, 8 or 10 make sure that you have the
administrator privileges;
In case you have to program more than one device, using the "UD Update", you
have to cancel the AR table every time you connect a new device on Ethernet. For
do this you have to launch the "Command rompt" and write the command "arp -
d". ay attention that with Windows Vista, Seven, 8, 10 you have to launch the
"Command rompt" with Administrator Rights;
ay attention at Firewall lock.
Warning:
In the case of HD67647 you have to use the software “HD67647”: www.adfweb.com\download\filefold\SW67647.zip.
Figure 6: “Error” window

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
EtherNet/IP
Master
/
DeviceNet
Slave
Document code: MN67647_ENG Revision 1.000 age 20 of 23
MECHANICAL DIMENSIONS:
Figure 7: Mechanical dimensions scheme for HD67647-A1