ADLINK Technology DIN-1040 User manual

Leading EDGE COMPUTING
DIN-1040
DIN Board
User’s Manual
Manual Rev.: 1.0
Revision Date: Dec. 30, 2017
Part No: 50-11257-1000

ii
Leading EDGE COMPUTING
Revision History
Revision Release Date Description of Change(s)
1.0 Dec. 30, 2017 Initial Release

Preface iii
DIN-1040
Preface
Copyright 2017 ADLINK Technology, Inc.
This document contains proprietary information protected by copy-
right. All rights are reserved. No part of this manual may be repro-
duced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, spe-
cial, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the Euro-
pean Union's Restriction of Hazardous Substances (RoHS) direc-
tive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manu-
facturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification pur-
poses only and may be trademarks and/or registered trademarks
of their respective companies.

iv Preface
Leading EDGE COMPUTING
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
NOTE:
NOTE:
Additional information, aids, and tips that help users perform
tasks.
CAUTION:
Information to prevent minor physical injury, component dam-
age, data loss, and/or program corruption when trying to com-
plete a task.
WARNING:
Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.

Table of Contents v
DIN-1040
Table of Contents
Preface.................................................................................... iii
List of Tables......................................................................... vii
List of Figures........................................................................ ix
1 Introduction ........................................................................ 1
1.1 Overview.............................................................................. 1
1.2 Specifications....................................................................... 1
1.3 I/O Connectors and Indicators ............................................. 2
1.3.1 Digital I/O and Power.................................................. 3
1.3.2 RS-232 ....................................................................... 4
1.3.3 Main Power................................................................. 5
1.3.4 PWM LED Control Out ............................................... 5
1.3.5 Hardware Trigger Input............................................... 6
1.3.6 Hardware Trigger Input............................................... 6
1.3.7 General Purpose Isolated Digital Input....................... 6
1.3.8 General Purpose Isolated Digital Output .................... 8
1.3.9 LED Status Indicators............................................... 10
1.4 Accessory Connection ....................................................... 11
Important Safety Instructions.............................................. 13
Getting Service...................................................................... 17

vi Table of Contents
Leading EDGE COMPUTING
This page intentionally left blank.

List of Tables vii
DIN-1040
List of Tables
Table 1-1: I/O Connector Legend ................................................ 3
Table 1-2: Digital I/O and Power Pin Assignments...................... 4
Table 1-3: System UART Pin Assignments ................................. 4
Table 1-4: Power Pin Assignments.............................................. 5
Table 1-5: PWM LED Pin Assignments ....................................... 5
Table 1-6: Hardware Trigger Input Pin Assignments................... 6
Table 1-7: Trigger Input Electrical Specification .......................... 6
Table 1-8: Isolated Digital Input Pin Assignments ....................... 7
Table 1-9: Isolated Digital Input Electrical Specification .............. 8
Table 1-10: Isolated Digital Output Pin Assignments .................... 8
Table 1-11: Isolated Digital Output Electrical Specification ........... 9
Table 1-12: DIN-1040 Accessories.............................................. 12

viii List of Tables
Leading EDGE COMPUTING
This page intentionally left blank.

List of Figures ix
DIN-1040
List of Figures
Figure 1-1: I/O Panel..................................................................... 2
Figure 1-2: Hardware Trigger Input Circuit ................................... 6
Figure 1-3: Isolated Digital Input Circuit........................................ 7
Figure 1-4: Isolated Digital Output Circuit ..................................... 9
Figure 1-5: Connection Relay Application Circuit ......................... 9
Figure 1-6: DIN-1040 Accessory Connection ............................. 11

xListofFigures
Leading EDGE COMPUTING
This page intentionally left blank.

Introduction 1
DIN-1040
1 Introduction
1.1 Overview
The DIN-1040 is a terminal block that simplifies power and I/O sig-
nal configuration for the ADLINK NEON-1020/40 smart camera.
1.2 Specifications
I/O Interface
Digital Output
Exposure Output
4 channel isolated multi-function open collector
output
Digital or exposure output function as
configured by software
Operating voltage range up to 24VDC
Open collector sink currents max. 300 mA
Overcurrent protection per channel
Digital Input 4-channel isolated digital input
Operating voltage range up to 24 VDC
Trigger Input One trigger input
Operating voltage range up to 24 VDC
PWM LED Out
Output voltage
24 VDC, +/- 10%
(output power shares
system power source)
Output current 500 mA
Ethernet Two RJ-45 connectors, GbE signal bypass
only

2Introduction
Leading EDGE COMPUTING
1.3 I/O Connectors and Indicators
Figure 1-1: I/O Panel
RS-232 D-SUB9 male connector, TXD and RXD signal
only
USB 4 channel USB 1.1 full speed
DC Output Isolation 5VDC, +/- 15%, max. 100mA
DC Input 24V DC, +/- 10%, max. 30 VDC
DC Input Power
Protection
Over-current: (fuse 3A )
Power reverse
Mechanical/Environmental
Dimensions 121.92mm x 71.7mm
Operating
Temperature 0°C to 50°C
Humidity Approx. 95% @ 40°C (non-condensing)
Safety CE, FCC Class A
I/O Interface
A
B
C
D
E
FG
H
I
J
K

Introduction 3
DIN-1040
Table 1-1: I/O Connector Legend
1.3.1 Digital I/O and Power
The D-SUB26 (female) connector transmits and receives both RS-
232 and digital I/O, trigger, and PWM LED OUT signals, and
power.
ADigital I/O and power FIsolated Digital Output
BRS-232 GIsolated Digital Input
CPower HDI/O status LED
DPWM LED Output ILAN Port
EHardware Trigger Input JUSB Port (Type A) x4
KUSB Port (Type B)
Pin Signal Pin Signal
1 RS232 RXD 14 GND
2 DO3 /Strobe out 3 15 GND
3 DO1 /Strobe out 1 16 GND
4 Hardware Trigger input (-) 17 GND
5 Hardware Trigger input (+) 18 GND
6 PWM LED out (+) 19 RS232 TXD
7 PWM LED out (-) 20 DO2 /Strobe out 2
1
26

4Introduction
Leading EDGE COMPUTING
Table 1-2: Digital I/O and Power Pin Assignments
1.3.2 RS-232
A D-SUB9 (male) connector
Table 1-3: System UART Pin Assignments
8 System PWR 21 DO0 /Strobe out 0
9 System PWR 22 DI3
10 GND 23 DI0
11 GND 24 DI2
12 GND 25 DI1
13 GND 26 GND
Pin Signal
1N/C
2RXD
3TXD
4N/C
5GND
6N/C
7N/C
8N/C
9N/C
Pin Signal Pin Signal
1
9

Introduction 5
DIN-1040
1.3.3 Main Power
Table 1-4: Power Pin Assignments
1.3.4 PWM LED Control Out
Table 1-5: PWM LED Pin Assignments
Pin Signal
1 Power in (+)
2GND
3 Isolated 5V power out
4 Isolated GND
Pin Signal
1 PWN output (+)
2 PWN output (-)
14
12

6Introduction
Leading EDGE COMPUTING
1.3.5 Hardware Trigger Input
Table 1-6: Hardware Trigger Input Pin Assignments
1.3.6 Hardware Trigger Input
One hardware trigger input is provided.
Figure 1-2: Hardware Trigger Input Circuit
Table 1-7: Trigger Input Electrical Specification
1.3.7 General Purpose Isolated Digital Input
Four isolated digital input channels are provided
Pin Signal
1 Trigger input (+)
2 Trigger input (-)
Min. Max.
Number of Channels 1 digital input
Normal Input High Threshold +2V +24V
Normal Input Low Threshold 0V +0.8V
Max. Input Voltage +24V
12
1.2kΩ
DIN-1040 NEON-1020/1040
Hardware Trigger input (+)
Hardware Trigger input (-)
Max. 24VDC
1kΩ

Introduction 7
DIN-1040
Table 1-8: Isolated Digital Input Pin Assignments
Figure 1-3: Isolated Digital Input Circuit
Pin Signal
1DI0(+)
2 DI0 (-)
3DI1(+)
4 DI1 (-)
5DI2(+)
6 DI2 (-)
7DI3(+)
8 DI3 (-)
9 Isolated GND
Min. Max.
Number of Channels 4 digital inputs
Input Resistance 2.4KΩ
Normal Input High Threshold +2.4V +24V
Normal Input Low Threshold 0V +1.8V
1
9
2.4k
`
DIN-1040
DI(+)
DI(-)

8Introduction
Leading EDGE COMPUTING
Table 1-9: Isolated Digital Input Electrical Specification
1.3.8 General Purpose Isolated Digital Output
Four isolated digital output channels are provided, such that, in the
common ground connection of digital output, as shown, when a 1
(logic high) is written by FPGA to a DO channel, sink current
passes through the transistors and the DO channel goes low, and
when a 0 (logic low) is written by FPGA to a DO channel, no cur-
rent passes through the transistors and the DO channel goes high.
Table 1-10: Isolated Digital Output Pin Assignments
Max. Input Voltage +24V
Pin Signal
1 D00 (+)
2 Isolated GND
3 DO1 (+)
4 Isolated GND
5 DO2 (+)
6 Isolated GND
7 DO3 (+)
8 Isolated GND
9VFB
(DO flyback diode power source)
Min. Max.
1
9

Introduction 9
DIN-1040
Figure 1-4: Isolated Digital Output Circuit
Figure 1-5: Connection Relay Application Circuit
Table 1-11: Isolated Digital Output Electrical Specification
Number of Channels 4 digital outputs
Output Type Sink current for each channel
Max 300mA/Channel
Output Working Voltage Max 24V
Overcurrent Protection Max 750mA per channel @25°C
Output Inactive Leakage
Current Max 0.1µA@DO=24V
`
`
+5V
ISO +5V
Flyback diode
VFB
DO (+)
Isolated GND
DIN-1040
LED
`
`
+5V
ISO +5V
Flyback diode
VFB
DO (+)
Isolated GND
DIN-1040
Relay
Relay coil supply (-)
Relay coil supply (+)
LED

10 Introduction
Leading EDGE COMPUTING
1.3.9 LED Status Indicators
LED Color Status Indicator
PWR Green DC power on: ON
DC power off: OFF
DI0 Green DI high: ON
DI low: OFF
DI1 Green DI high: ON
DI low: OFF
DI2 Green DI high: ON
DI low: OFF
DI3 Green DI high: ON
DI low: OFF
DO0 Yellow DO active: ON
DO inactive: OFF
DO1 Yellow DO active: ON
DO inactive: OFF
DO2 Yellow DO active: ON
DO inactive: OFF
DO3 Yellow DO active: ON
DO inactive: OFF