Advantech ASMB-785 Installation and operation manual

ASMB-785 Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 ASMB-785 Startup Manual
• 1 Driver CD (user’s manual is included)
• 2 Serial ATA HDD data cables
• 2 Serial ATA HDD power cables
• 1 I/O port bracket
• 1 Warranty card
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note: Acrobat Reader is required to view any PDF
file.Acrobat Reader can be downloaded at:
http://www.adobe.com/downloads/ (Acrobat is a
trademark of Adobe)
ASMB-785 LGA 1151 Intel Xeon E3-1200 v5/ 6th Gener-
ation Core Series ATX Server Board with DDR4, 4 PCIe,
3 PCI, 6 USB 3.0, 6 COM, 6 SATA3, Quad/Dual LANs
Startup Manual
Standard SBC Functions
• CPU: Intel LGA1151 Xeon E3-1200 v5 /Core i3/i5/i7
series processors
• BIOS: AMI 128 Mb SPI BIOS
• Chipset: Intel® C236
• System memory: Dual Channel DDR4 ECC/Non-ECC
1600/1866/2133 MHz unbuffered DIMM, Max. 64 GB
Note: Due to the inherent limitations of PC architecture,
the system may not fully detect 32 GB RAM
when 64 GB RAM is installed.
• SATA3 Interface: 6 SATA3 6Gb/s ports to support Intel
Matrix Storage with software RAID 0, 1, 10 & 5. (for
Windows only)
• Serial ports: Six serial ports, only supports RS-232
• Keyboard/Mouse connector: Supports standard PS/2
keyboard and mouse via KMBS1 pin header
• Watchdog timer: 255 level timer intervals (sec)
• USB 3.0: Supports up to Six USB 3.0 ports. Four ports
are in rear I/O, and two ports are on-board pin header.
• USB 2.0: Supports up to seven USB 2.0 ports (1* Type-A)
Display Interface
• Chipset: CPU integrated Intel HD graphics controller
• Display Memory: 1 GB maximum shared memory with 2
GB and above system memory installed
• Resolution:
- Supports RGB up to 1920 x 1200 resolution @ 60 Hz
refresh rate
- Supports DVI up to 1920 x 1200 resolution@ 60 Hz
refresh rate
Ethernet Interface
• Interface: 10/100/1000 Mbps
• Controller: LAN1:Intel
®
I219LM; LAN2 ~ LAN4: Intel®
I201AT
Mechanical and Environmental
• Dimensions (L x W): 244 x 304 mm (9.6” x 12”)
• Power supply voltage: +3.3 V, +5 V, ±12 V, 5 Vsb
• Power consumption: Max. load: +3.3 V @ 0.96 A, +5 V
@ 1.58 A, +12 V @ 0.32 A, +12 V (8P) @ 7.21 A, +5 Vsb
@ 0.11 A, -12 V @ 0.06 A
• Operating temperature: 0 ~ 60° C (Depends on CPU
speed and cooler solution)
• Weight: 0.75 kg (weight of board)
Specications
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our
support website at:
http://support.advantech.com.tw/support/new_de-
fault.aspx
This manual is for the ASMB-785 series Rev. A1
Part No. 2001S78510
Print in China
1st Edition,
November 2015

2 ASMB-785 Startup Manual
Connector list
LPC1
Low pin count connector for
Advantech TPM LPC and
RS232/485 modules.
VOLT1 Voltage Display
PMBUS1 PMBUS connector to communi-
cate with power supply
LPT1 Parallel port
AUDIO1 Audio Connector
BH2 For optional battery kit
EX_THR1 For thermometer kit
SGPIO1, SGPIO2 Serial General Purpose I/O
JFP1 Power Switch / Reset connector
JFP2 External speaker / HDD LED
connector/ SM Bus connector
JFP3
Keyboard Lock and Power LED
Suspend: Fast flash (ATX/ AT)
System On: ON (ATX/ AT)
System Off: OFF (ATX/AT)
SPDIF_OUT1 SPDIF Audio output pin header
BMC1 BMC connector to support IPMI-
1000 module
Jumper list
Label Function
JCMOS1 CMOS clear
JME1 Intel ME Disable Jumper for ME/
BIOS update
JWDT1 Watch Dog Reset
JUSB1
Rear window USB2.0/3.0 port
power source switch between
+5 VSB and +5 V
JUSB2
On board USB2.0/3.0 port
power source switch between
+5 VSB and +5 V
CPUFAN_
SEL1,SYSFAN_SEL1
FAN PWM(1-2)/DC mode selec-
tion(2-3)
PSON1 AT(1-2) / ATX(2-3)
JCASE1 Case Open
JPEG1, JPEG2
PCIEX16_SLOT6 PCIe Link
swtich between one x16 or two
x8 or x8, two x4
JGREEN1 Enable/Disable deep sleep
mode
JTHR_SEL1 To select on board or external
thermometer
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each jumper and connector.
Connector list
Label Function
ATXPWR1 ATX 24 Pin main power connec-
tor (for System)
ATX12V1 Processor power connector(for
CPU)
SATA0~5 SATA III (6Gb/s)
USB7_8, USB9_10,
USB11_12 USB 2.0 Port (Header)
USB13 USB 2.0 Port (USB Type A)
USB3_4 USB 3.0 Port (Header)
PCI_SLOT1,
PCI_SLOT3,
PCI_SLOT5
PCI slot
PCIEX4_SLOT2,
PCIEX4_SLOT7 PCIe x4 slot (Gen3 x4 link)
PCIEX16_SLOT4,
PCIEX16_SLOT6
PCIE x16 slots (one Gen3 x16
link for slot 6 or two Gen3 x8
link)
DIMMA0,DIMMA1,
DIMMB0,DIMMB1 DDR4 288-pin slot
CPUFAN0 CPU FAN connector
SYSFAN0,SYSFAN1,
SYSFAN2,SYSFAN3 System FAN connector
LAN1_USB1_2,
LAN2_USB5_6
LAN1 / USB 3.0 port 1, 2 stack
connector
LAN2 / USB 3.0 port 5, 6 stack
connector
LAN3_4 LAN3 & LAN4 connector
VGA1_COM1 VGA+COM connector
DVI1_DVI2 DVI-D connector
KBMS1 External keyboard and mouse
connector(6 pin)
SPI_CN1 SPI flash card pin header
LANLED1, LANLED2 LAN LED extension connector
SMBUS1 SM Bus From PCH
GPIO1 8-bit GPIO header
FPAUD1 Audio front panel header
COM2, COM3_4,
COM5_6 Serial port: RS-232
Jumpers and Connectors Jumpers and Connectors (Cont.)

ASMB-785 Startup Manual 3
JPCICLK1 PCI slot clock selection between
33 and 66 MHz
JWDT1: Watchdog timer output option
Closed Pins
Result
1-2 System reset*
2-3 NC
*: Default
PSON1: ATX, AT mode selector
Closed Pins
Result
1-2 AT Mode
2-3 ATX Mode*
*: Default
JCMOS1/JME1: CMOS clear/ME update function
Closed pins Result
1-2
Keep CMOS data/Disable ME update*
2-3 Clear CMOS data/Enable ME update
*: Default
Keep CMOS data/Disable ME update Clear CMOS data/Enable ME update
System Reset 1-2 Closed NC 2-3 Closed
1 2 3
1 2 3
AT Mode 1-2 closed ATX Mode 2-3 closed
1 2 3
1 2 3
1 2 3
1 2 3
JFP1, JFP2
Pin.3 #PWR_SW
Pin.6
GND
Pin.9 #RST_SW
Pin.12 GND
*Power button pin is located in Pin 3 & 6 of front panel
connector
The CD disc contains a driver installer program that will
lead you through the installation of various device drivers
needed to take full advantage of your motherboard.
The computer is supplied with a battery-powered realtime
clock circuit. There is a danger of explosion if battery is
incorrectly replaced. Replace only with same or equivalent
type recommended by the manufacturer. Discard used bat-
teries according to manufacturer’s instructions.
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired opera-
tion
3 6 9 12 PWRSW RESET
HDDLED
SNMP
JFP1
&
1(+) 4 7 10(-)
HDDLED
SM_BUS
SPEAKER
JFP2
&
PWRLED & KEYLOCK
12345JFP3
2(+) 5(-) 8 11
Jumpers and Connectors (Cont.) Installation Note
Declaration of Conformity
Software Installation

4 ASMB-785 Startup Manual
Board Layout: Jumper and Connector Locations
Board Layout
LAN3_4
VGA1_COM1
DVI1_DVI2
PMBUS1
AUDIO1
LAN1_
USB1_2
LAN2_
USB5_6
ATXPWR1
SYS
FAN0
JFP3
JCMOS1
COM2
PCIEX4_SLOT2
GPIO1
ATX12V1
EX_
THR1
FPAUD1
PCIEX16_SLOT4
PCIEX4_SLOT7
SYSFAN_
SEL1
PSON1
Intel LGA1151 Socket
DIMM A0
DIMM A1
DIMM B0
DIMM B1
SMBUS1
VOLT1
JUSB2
CPU FAN0
JTHR_SEL1
LAN LED
1 & 2
JGREEN1
JWDT1
JPEG1~3
SYS
FAN1 & 2
JFP1 + JFP2
COM3_4
JCASE1
COM5_6
SATA1~SATA5
JUSB1
Intel C236 PCH
USB3_4
KBMS1
USB7_8
USB9_10
USB11_12
SPDIF_OUT1
SYSFAN3
PCIEX16_SLOT6
JME1
SPI_CN1
CPUFAN_
SEL1
PCI_SLOT1
PCI_SLOT3
PCI_SLOT5
LPC1
LPT1
USB13
SATA0
BMC1
BH2
JPCICLK1
SGPIO1 & 2
SYS_LED1