Advantech PCE-2029 Installation and operation manual

PCE-2029/2129 Startup Manual 1
PCE-2029/2129 Compact Industrial Computer System
with 6th/7th Gen Intel® Core™ i CPU Socket (LGA 1151)
Startup Manual
Specications (Cont.)
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
https://advt.ch/dd116
This manual is for the PCE-2029/2129 series Rev. A1.
Part No. 2041202901
Printed in China
2nd Edition
June 2019
• Systemmemory: Supports dual channel DDR4
SODIMM-2133/2400 MHz, 16 GB per slot without ECC
function; Max. capacity is 32GB
Note: Due to the inherent limitations of PC architecture,
the system may not fully detect 64 GB RAM
when 64 GB RAM is installed
• SATA interface: 2 on-board Serial ATAIII connectors
support data transmission rate up to 600 MB/s. All two
SATAIII ports support Advanced Host Controller Interface
(AHCI) technology. Q170 can support RAID 0, 1, 5, 10.
• LPC interface: Advantech-designed LPC connector sup-
ports TPM module
• Serial ports: 4 serial ports: COM1, COM2 are RS-
232/422/485, COM3,COM4 are RS-232 with BIOS menu
options
• Watchdogtimer:1~255 sec/min timer level intervals
• USB3.0/2.0:8 USB ports:
- PCE-2129 : 1/2/3/4/5/6 are USB 3.0, 7/8 USB2.0
- PCE-2029 : 1/2/3/4 are USB 3.0, 5/6/7/8 USB2.0
Graphics
• Q170:Intel® HD Graphics 530, supports DirectX 12
• H110:Intel® HD Graphics 510, supports DirectX 12
Ethernetinterface
• Interface:10/100/1000 Mbps
• Controller:
- PCE-2129 : LAN1: Intel ® I219LM, LAN2: Intel® i210AT
- PCE-2029 : LAN1: Intel ® I219V, LAN2: Intel® i210AT
Audio
• Line-out
• Mic-in
Storage
• SATAx2
• mSATAx1
- PCE-2129 : mSATA/MiniPCIe by Hardware Auto dection
- PCE-2029 : mSATA
MechanicalandEnvironmental
• Dimensions(LxW):180 x 127 mm (7.08” x 5”)
• PowerConsumption:
Intel Core Intel i7-7700@ 3.60Ghz DDR4 16G x 2
Maximum: +19V at 7.95A , +24V at 6.28A
• Operatingtemperature:0 ~ 45° C (depending on CPU)
• Weight:0.38 kg (weight of board)
Before you begin installing your card, please make sure that
the following items have been shipped:
• PCE-2029/2129 Startup Manual
• Warranty card
• I/O bracket
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note: Acrobat Reader is required to view any PDF
file. Acrobat Reader can be downloaded at:
www.adobe.com/Products/acrobat/readstep2.
html (Acrobat is a trademark of Adobe)
StandardFunctions
• CPU:LGA1151 6th and 7th Generation Intel® Core™ i7/
i5/i3/Celeron/Pentium
Note: Intel 7th generation processors only support
Windows 10 (64-bit).
• BIOS:AMI 128 Mb SPI BIOS
• Chipset:
- PCE-2029 : Intel® H110 chipset
- PCE-2129 : Intel® Q170 chipset
Specications

2 PCE-2029/2129 Startup Manual
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each jumper and connector.
Connector / Jumper List
Label Function
JWDT1+JOBS1 Watchdog Reset
LPC1 Low pin count connector for Advan-
tech designed LPC modules
LAN1_USB2C1 LAN1 / USB 2.0 Port 7,8
LAN2_USB3C2
LAN2 /
PCE-2129 : USB 3.0 Port5/6
PCE-2029 : USB 2.0 Port5/6
VGA1 VGA connector
HDMI1 HDMI connector
COM1-1 2 x RS232/422/485 (COM1, COM2)
COM3-1 2 x RS232 (COM3, COM4)
JFP1 Power Switch / Reset connector
JCASE1 Case Open connector
PSON1 AT(1-2) / ATX(2-3) mode selector
CPUFAN1 CPU FAN connector (4-pin)
AUDIO1 Audio connector (Line-out, Mic-In)
USB3C1 USB3.0 1/2/3/4
BIOS1 SPI ash card pin header
JCMOS1
CMOS clear
JME1 Intel ME Enable/Disable jumper
GPIO1 8 bit digital I/O connector
SW1 USB power mode and VGA mode
change
USB2H1 USB port (Q170 only)
SW2 Power ON/OFF Switch
DP1 3rd Display output
SATA1/2 Serial ATA1/2
JCFG1 Reserve for RD debug
JSMB1 Reserve for RD debug
JCMOS1: CMOS and ME clear function
Pins Result
1-2 Keep CMOS data*
2-3
Clear CMOS data
* Default
12 3
12 3
*Keep CMOS data Clear CMOS data
PSON1: ATX, AT mode selector
Closed Pins
Result
1-2 AT Mode
2-3 ATX Mode*
* Default
JFP1
Closed Pins
Result
1 Power ON/OFF
2,4 GND
3 System Reset
5 Watch Dog Clear
SW1
Switch State Setting
SW1-1 1* - 8 LAN1_USB2C1_1 / LAN2_
USB3C2_1 not provide stand by
charging
SW1-2 2* - 7 USB3C1 not provide stand by
charging
SW1-3 3* - 6 USB2H1(Q170 only) not provide
stand by charging
SW1-4 4* - 5 VGA is always on VGA will be ON by
cable detected
JWDT1 + JOBS1
Closed Pins
Result
2-3* Watch Dog Timer Reset
4-5* Enable H/W monitor alarm
* Default setting
Caution! The computer is supplied with a battery-powered
realtime clock circuit. There is a danger of explo-
sion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended
by the manufacturer. Discard used batteries ac-
cording to manufacturer’s instructions.
12 3
12 3
AT Mode 1-2 closed *ATX Mode 2-3 closed
Jumpers and Connectors Jumpers and Connectors (Cont.)

PCE-2029/2129 Startup Manual 3
Declaration of Conformity
Board Layout
This device complies with the requirements in Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Figure 1 : Front Side Board Layout: Jumper and Connector Locations
Figure2 : Rear side Jumper and Connector Locations
DIMMA1
DIMMB1
CPUFAN1
COM1-1
MINIPCIE1
CPU0 PCH
Q170/H110
LPC1
AUDIO1
SW2
USB3C1
LAN2_USB3C2_1
LAN1_USB2C1_1
VGA1+HDMI1
JCMOS1
JFP1
JSMB1
JCFG1
DP1
SW1
JCASE1
JME1
PSON1
USB2H1(Q170 only)
JWDT1+JOBS1
SATA1
SATA2
COM3-1
GPIO1
BIOS1
BIOS-SPI