Advantech TPC-662G-B1E User manual

TPC-66X Series
AMD LX800 Touch Panel
Computers with 6.4"/ 5.6"
VGA TFT LCD
User Manual

TPC-66X Series User Manual ii
Copyright
The documentation and the software included with this product are copy-
righted 2007 by Advantech Co., Ltd. All rights are reserved. Advantech
Co., Ltd. reserves the right to make improvements in the products
described in this manual at any time without notice. No part of this man-
ual may be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reli-
able. However, Advantech Co., Ltd. assumes no responsibility for its use,
nor for any infringements of the rights of third parties, which may result
from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of
Microsoft Corp.
All other product names or trademarks are properties of their respective
owners.
This Manual Covers the Following Models
• TPC-66X Series-B1E
• TPC-662G-B1E
• TPC-66X Series
Part No. 2003066001 2nd Edition
Printed in Taiwan March 2007

iii
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its prod-
ucts will be free from defects in materials and workmanship for two years
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper instal-
lation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous test-
ing, most of our customers never need to use our repair service. If an
Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any
onscreen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your man-
ual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows
us to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for war-
ranty service.
5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

TPC-66X Series User Manual iv
CE
This product has passed the CE test for environmental specifications
when shielded cables are used for external wiring. We recommend the use
of shielded cables. This kind of cable is available from Advantech. Please
contact your local supplier for ordering information.
FCC Class A
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
Technical Support and Assistance
Step 1. Visit the Advantech web site at www.advantech.com/support
where you can find the latest information about the product.
Step 2. Contact your distributor, sales representative, or Advantech's cus-
tomer service center for technical support if you need additional
assistance. Please have the following information ready before
you call:
- Product name and serial number
- Description of your peripheral attachments
- Description of your software (operating system, version, appli-
cation software, etc.)
- A complete description of the problem
- The exact wording of any error messages

v
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning.
Use a damp cloth. Do not use liquid or spray detergents for clean-
ing.
4. For plug-in equipment, the power outlet socket must be located
near the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Drop-
ping it or letting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before con-
necting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not
place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or elec-
trical shock.
13. Never open the equipment. For safety reasons, the equipment
should be opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked
by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work
according to the user's manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT
WHERE THE STORAGE TEMPERATURE MAY GO BELOW -

TPC-66X Series User Manual vi
20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAM-
AGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A
CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS
INCORRECTLY REPLACED. REPLACE ONLY WITH THE
SAME OR EQUIVALENT TYPE RECOMMENDED BY THE
MANUFACTURER, DISCARD USED BATTERIES ACCORD-
ING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-
1:1982 is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1.
Advantech disclaims all responsibility for the accuracy of any statements
contained herein.

vii Table of Contents
Contents
Chapter 1 General Information ....................................... 2
1.1 Introduction ....................................................................... 2
1.2 Specifications .................................................................... 3
1.2.1 System Kernel ................................................................ 3
1.2.2 I/O Ports ......................................................................... 3
1.2.3 Safety and Environment ................................................. 3
1.3 LCD Specifications ........................................................... 4
1.4 Touchscreen Specifications............................................... 4
1.5 Power................................................................................. 4
1.6 I/O Ports Arrangement ...................................................... 5
Figure 1.1:I/O Port Arrangement ................................... 5
1.7 Panel Mounting ................................................................. 5
Figure 1.2:Panel Mounting ............................................ 6
1.8 Exploded Diagram............................................................. 6
Figure 1.3:Assembly (exploded) .................................... 6
1.9 Dimensions and Cutout ..................................................... 7
Figure 1.4:Dimensions & Cutout ................................... 7
Chapter 2 System Setup.................................................. 10
Figure 2.1:Unpack the Package ................................... 10
Figure 2.2:Install CompactFlash Memory Card .......... 10
Figure 2.3:Power Connector and Power Lines ............ 11
Figure 2.4:Pin Assignment on the Power Receptor ..... 11
Figure 2.5:Plugging in the Power Line ........................ 12
Figure 2.6:Turn on the System .................................... 12
Chapter 3 System Engine................................................ 14
Table 3.1:Mainboard Connectors & Jumper Settings . 14
Figure 3.1:Main Board Connectors - 1 ........................ 15
Figure 3.2:Main Board Connectors - 2 ........................ 15
Chapter 4 Software Configuration ................................ 18
4.1 VGA Driver Installation.................................................. 18
Figure 4.1:Device Manager ......................................... 18
Figure 4.2:Update Driver ............................................. 19
Figure 4.3:Update Wizard-1 ....................................... 19
Figure 4.4:Update Wizard-2 ........................................ 20
Figure 4.5:Update Wizard-3 ....................................... 20
Figure 4.6:Update Wizard-4 ........................................ 21
Figure 4.7:Update Wizard-5 ....................................... 21
Figure 4.8:Update Wizard-6 ........................................ 22
Figure 4.9:Driver Installation Complete ...................... 22
4.2 Entertainment Encryption/Decryption Driver................. 23
Figure 4.10:Device Manager ....................................... 23
Figure 4.11:Install Wizard - 1 ..................................... 23

TPC-66X Series User Manual viii
Figure 4.12:Install Wizard - 2 ...................................... 24
Figure 4.13:Install Wizard - 3 ...................................... 24
Figure 4.14:Driver Installation Complete .................... 25
Chapter 5 Features in Windows XP Embedded........... 28
5.1 EWF ................................................................................ 28
5.2 HORM............................................................................. 29
5.3 Advantech Utilities.......................................................... 29
5.3.1 Version Information ..................................................... 30
5.3.2 OSLock and OSUnLock .............................................. 30
5.3.3 HORM ......................................................................... 30
Appendix A Serial Port Settings........................................ 32
A.1 Jumper Setting................................................................. 32
A.2 Data Format Control Setting (SW2)................................ 33
A.3 Baud Rate Setting (SW3) ................................................ 34
Appendix B Watchdog Timer Programming................... 36
B.1 Overview ......................................................................... 36
B.2 Watchdog Timer Programming....................................... 37
Figure B.1:Watchdog Timer Programming ................. 37
Table B.1:Watchdog Timer Registers ......................... 38
B.3 Example Programs .......................................................... 39
Appendix C Watchdog Timer Programming on WinCE 46
C.1 DeviceIOControl ............................................................. 46
C.1.1 Parameters .................................................................... 47
C.2 How to Use the Control Code ......................................... 48
C.2.1 IOCTL _WDT_ENABLE: ........................................... 48
C.2.2 IOCTL _WDT_DISABLE: .......................................... 48
C.2.3 IOCTL_WDT_STROBE: ............................................ 48
C.2.4 IOCTL_WDT_GETTIMEOUT: .................................. 49
C.2.5 IOCTL_WDT_SETTIMEOUT: .................................. 49
C.2.6 IOCTL_WDT_REBOOT: ........................................... 49
C.3 Examples ......................................................................... 50
Appendix D Accessory Kit Assembly Procedure............. 54
D.1 CompactFlash to IDE Transfer Kit ................................. 54
Figure D.1:Adapter Board and IDE Cable ................... 54
Figure D.2:Connecting the Adapter Board .................. 54
Figure D.3:CompactFlash Slot .................................... 55
Figure D.4:Insert the Adapter Board into the CF slot .. 55
Figure D.5:Inserted Adapter Board ............................. 55
Figure D.6:Connect the CD-ROM via the IDE Cable . 56
Figure D.7:Plugging in the CD-ROM Drive ............... 56
Appendix E Touchscreen Installation & Configuration. 58
E.1 Driver Installation ........................................................... 58
Figure E.1:Setup.exe .................................................... 58
Figure E.2:Install Wizard - 1 ...................................... 58

ix Table of Contents
Figure E.3:Install Wizard - 2 ....................................... 59
Figure E.4:Install Wizard - 3 ....................................... 59
E.2 Uninstall the Driver......................................................... 60
Figure E.5:Uninstall -1 ................................................ 60
Figure E.6:Uninstall -2 ................................................ 60
E.3 Touchscreen Calibration ................................................. 61
Figure E.7:Standard Calibration -1 .............................. 61
Figure E.8:Standard Calibration -2 .............................. 62
Figure E.9:Standard Calibration -3 .............................. 62
Figure E.10:Advanced Calibration -1 ......................... 63
Figure E.11:Advanced Calibration -2 .......................... 64
Figure E.12:Plot Calibration Data ............................... 64
Figure E.13:Draw ........................................................ 65
Figure E.14:Clear Screen ............................................. 66
Figure E.15:Option ..................................................... 66
Appendix F Fuse Specifications ........................................ 68
F.1 Fuse Specifications.......................................................... 68
F.2 Fuse Replacement ........................................................... 68
Figure F.1:Fuse Replacement ...................................... 68

TPC-66X Series User Manual x

2
CHAPTER
1
General Information
This chapter gives background infor-
mation on TPC-66X Series.
Sections include:
• Introduction
• Specifications
• I/O Ports Arrangement
• Panel Mounting
• Exploded Diagram
• Dimensions & Cutout

TPC-66X Series User Manual 2
Chapter 1 General Information
1.1 Introduction
The TPC-66X Series touch panel computer is a state-of-the-art HMI
(Human Machine Interface). This operator interface with a 6.4” display is
an x86-based platform with these key features:
• Fanless
By using a low-power processor, the system does not have to rely on
fans, which often are unreliable and causes dust to circulate inside the
equipment.
• Bright Display
The TFT LCD display suits industrial demands for clear interfaces.
• Powerful Communication Capability
TPC-66X Series provides a powerful I/O interface for easily communi-
cating with other devices. The I/O interface includes serial ports,
Ethernet and USB 2.0 support. TPC-66X Series also supports the
expansion slot PC-104. This makes it easy to expand with the required
PC-104 modules.
• Windows CE Support
In addition to the OS support of Windows XP, Advantech offers plat-
form support for Windows CE and Windows XP embedded. The
optional Windows CE operating system specifically for the TPC-66X
Series is available for Windows CE application program builders.

3 Chapter1
1.2 Specifications
1.2.1 System Kernel
• CPU: GeodeLink Control Processor LX800 500MHz
• BIOS: Award 512KB flash memory
• South Bridge: GeodeLink Control Processor CS5536
• VGA: GeodeLink Control Processor LX800 500MHz
• Ethernet: Realtek RTL8100BL; IEEE 802.3u protocol compatible
• Watchdog Timer: W83627 watchdog timer; 1.6 second timeout period
• IDE: 1 EIDE channel supports one CompactFlash socket onboard
(Master) and one IDE interface harddrive (Slave)
1.2.2 I/O Ports
• 2 serial ports:RS-232(COM1)andRS-232/422/485(COM2)or(TPC-662G)
• 1 RJ-45 Ethernet port
• 1 PS/2 port: 6-pin mini-DIN ports for keyboard and mouse
• 2 USB 2.0 Ports: compliant with USB 1.0 and 1.1.
• PC-104 slot: supports 8-bit I/O card only.
1.2.3 Safety and Environment
Safety
• FCC Class A
• CE certificated
• The front bezel is compliant with NEMA 4 and IP65
Environment
• Operating Temperature: 0 ~ 50° C (32 ~ 122° F)
• Storage Temperature: -20 ~ 60° C (-4 ~ 140° F)
• Humidity: 40° C @ 10~95% relative humidity (non-condensing)
• Vibration: 1 grms (5~500Hz)
Note: COM1 and COM2 only support half-duplex
(Maximum baud rate: 115.2Kbps)
CAN-Bus only for TPC-662G

TPC-66X Series User Manual 4
1.3 LCD Specifications
• Display Type: TFT color LCD
• Size (diagonal): 6.4”
• Maximum Resolution: 640 x 480 (VGA)
• Maximum Colors: 256,000
• Pixel Pitch (W x H, mm): 0.203 x 0.203
• Viewing Angle: 90°
• Luminance (cd/m² ): 150
• Contrast Ratio: 180
• Operating Temperature: 0 ~ 50° C (32 ~ 122° F) (Ambient)
• Backlight: 1 CCFL
• Backlight Life Time: 20,000 hours
1.4 Touchscreen Specifications
• Touch Type: Resistive
• Base Glass Construction: Tempered Glass
• Resolution: 1024 x 1024
• Light Transmission: 75% typical
• Controller: RS-232 Interface
• Lifespan: 1 million touches at single point
1.5 Power
• Input Voltage: 18 - 32VDC (the fuse will become an open circuit if the
input level exceeds 33 VDC)
• Typical: 24VDC@1.82Amp
Note There might be several bright or dark pixels on
the LCD. This phenomenon is normal in today’s
LCD manufacturing.

5 Chapter1
1.6 I/O Ports Arrangement
The arrangement of the I/O ports is shown in Figure 1.1.
Figure 1.1: I/O Port Arrangement
1.7 Panel Mounting
1. There is an adhesive waterproof gasket on the Mg-AL front bezel.
Make sure the waterproof gasket is in position before installing
TPC-66X Series into the panel opening.
2. Install the TPC-66X Series into the panel opening.
3. Find the eight clampers and eight long screws in the accessory
pack. Hook the clampers to the holes around the four sides of the
bezel. Insert the screws into every clamper and fasten them. These
screws will push the mounting panel and fix the unit.
4. The suggested mounting panel thickness is less than 6 mm
(0.236”).

TPC-66X Series User Manual 6
Figure 1.2: Panel Mounting
1.8 Exploded Diagram
Figure 1.3: Assembly (exploded)

7 Chapter1
1.9 Dimensions and Cutout
• Weight: 0.8 kg
• Dimensions: 195 x 148 x 44.5 mm (W x H x D)
• Cutout: 188 x 141 mm (suggested)
Figure 1.4: Dimensions & Cutout

TPC-66X Series User Manual 8

2
CHAPTER
2
System Setup
This chapter provides a brief explana-
tion for operating TPC-66X Series.

TPC-66X Series User Manual 10
Chapter 2 System Setup
You can quickly get up and running by following the step-by-step instruc-
tions below.
1. Unpack the TPC-66X Series package. Please check the packing list
at the beginning of this manual to make sure every item is there.
Figure 2.1: Unpack the Package
2. Install a CompactFlash card containing Windows CE, embedded
Windows XP or another operating system.
Figure 2.2: Install CompactFlash Memory Card