AETEK C60-00F-01 User manual

C60-00F-01
C60-082-30-130
C60-164-30-250
C60-244-30-370
D60-044-30
D60-044-90
D60-084-30
H60-044-30-150
H60-044-90-250
H60-084-30-250
L2 PRO Gigabit PoE Switch Series
Network Topology System
User Manual
Copyright© AETEK Inc. 2021｜All rights reserved. All brand and product names are trademarks or registered
trademarks of their respective companies

ii
Table of Contents
NTS OVERVIEW ................................................................................................................. 1
GRAPHICAL MONITORING ............................................................................................. 2
Topology View .........................................................................................................................................2
Floor View.................................................................................................................................................9
Map View ................................................................................................................................................11
MANAGEMENT................................................................................................................ 12
Device List...............................................................................................................................................12
MAINTENANCE ............................................................................................................... 14
Floor Image ............................................................................................................................................14
Traffic Monitor.......................................................................................................................................15

1
NTS Overview
1. NTS is an intelligent management tool embedded in switches to intuitively help IT/TS
reduce support cost/time/effort.
2. All devices connected to the switches can be discovered and displayed by NTS
automatically using standard networking protocols such as LLDP, ONVIF, etc.
3. Users can operate the features below via an intuitive web GUI.
-Power down, remotely, the IP cameras, NVRs, or any PoE devices.
-Identify where exactly the broken cable is, remotely.
-Detect abnormal traffic issues on IP cameras/NVR.
-Monitor devices status intuitively, e.g. link up, PoE power, traffic, etc.
4. NTS supports up to 255 devices within 1 subnets.
The embedded Network Topology System is designed to be extremely easy-to-
use/manage/install IP Phone, IP Cam, or Wifi-AP for enterprise applications.
User can deploy IP Device through Topology/ Floor/ Map View to installation location, and
through Diagnostics and Traffic Monitor, they may also check link status and monitor
throughput as well.
Figure 1: The NTS Overview

2
Graphical Monitoring
Topology View
NTS can automatically discover all IP devices and display the devices by graphic networking
topology view. User could manage and monitor them by the Topology View, such as to
remotely diagnose the cable connection status, auto alarm notifications on critical events,
remotely reboot PoE device when it’s not alive. Therefore, the user can apply NTS platform
to solve the abnormal issues anytime and anywhere by tablet or smart phone, and keep the
network works smoothly.
Click Graphical Monitoring Topology View, you can see a visual view of the network
topology.
Figure 3: The Topology View
1
2
4
5
3

3
Parameter description:
1. Icon with plus and minus marks: Zoom in and zoom out the topology view, user can scroll
up/down with mouse to achieve the same purpose.
2. Icon with screen view type: Click it to change to Full Screen View of Topology or return
to the Normal View.
3. Icon with information list: User can select what kind of information should be shown on the
topology view of each device. Up to 3 items can be selected.
4. Device icon
I. Device category
⚫: It means the device is Switch.
⚫: It means the device is PC.
⚫: It means the device is IP Cam.
⚫: It means the device is IP Phone.
⚫: It means the device is AP.
⚫: It means the device is Router.
II. Device Status

4
⚫Icon with black mark: Device link up. User can select function and check issues.
⚫Icon with red mark: Device link down. User can diagnose the link status.
⚫Icon with numbers: It means some events happened (e.g. Device Off-line, IP
Duplicate…etc.) on the IP device, user can click on the device icon to check events in
Notification.
⚫Icon with question: It means the IP device is detected by NTS, but the device type
can’t be recognized which will be classified as an unknown device type.
III. Device consoles
⚫To left-click any device icon to display the device consoles for further actions:
Figure 5: The Device Console
⚫Dashboard Console: it displays device info and related actions for the device.
◆Different device type supports different function:
-If an IP device is recognized as NTS switch, it will support “Upgrade“, “PoE
Config“ function.
-If an IP device is recognized as PoE device, it will support more “PoE Reboot”
function in addition “Upgrade”.
◆Device Type: It can be displayed automatically. If an unknown type is detected, user can still

5
select type from a pre-defined list.
◆Device Name: Create your own Device Name or alias for easy management such as,
1F_Lobby_Cam1.
◆Model Name, MAC Address, IP Address, PoE Supply and PoE Used are displayed automatically
by NTS.
◆Http Port: Re-assign http port number to the device for better security.
◆Login: Click the Login Action Icon to log in the device via http for further configuration
or status monitoring.
◆Upgrade: Click it to upgrade software version.
◆PoE Config: Click it to configure the PoE function, enable/disable PoE Auto Checking or
enable/disable PoE mode for per port.
Figure 6: The PoE Configure
◆Diagnostics: Click Diagnostic Action Icon to perform the cable diagnostics, to exam
where the broken cable is, and, check if the device connection is alive or not by ping.
⚫Cable Status:

6
-Green icon: Cable is connected correctly.
-Red icon: Cable is not connected correctly. User can check the distance info (XX
meters) to identify the broken cable location.
⚫Connection:
-Green icon: Device is pinged correctly.
-Red icon: Device is not transmitted /receiving data correctly. Which means it might
not be pinged successfully.
Figure 7: The Diagnostics
◆PoE Reboot: Click Reboot Action Icon to reboot the device remotely so as recover the
device back to its normal operation.
◆Icon with blank node: When NTS switch detects more than two IP devices from the
same port, switch can’t resolve this IP device’s layout, instead, it will show a blank node to
present this situation. User can use “Parent Node” function to adjust layout in Dashboard.
⚫Notification Console: It displays alarms and logs triggered by events.

7
Figure 8: The Notification Console
⚫Monitor Console: It displays the traffics for device health check purpose.
◆For each IP device except NTS switches, User can set a threshold of throughput for IP devices,
and get notification when throughput is lower or higher than settings.
◆If both values are “0”, it means the function is disabled.
◆Polling interval is 1 second, when the page is closed, the Polling interval will change to around
5 seconds.
Figure 9: The Monitor Console

8
5. In the upper right corner, there is a “Setting icon”. When user clicks the icon, it
will pop-up Device, Group, Config, export topology view and advanced search functions
for the topology.
⚫Device Search Console
All devices and info. It will show on the list.
Figure 10: The Device Search Console
A
C
B
Test02
Function
A.
Filter devices by Device Type
B.
Search devices by key words full text search
C.
Save the whole View to SVG, PNG or PDF

9
Floor View
User can easily plan IP devices installation location onto the custom uploaded floor images.
Figure 13: The Floor View
⚫Anchor Devices onto Floor Maps
⚫Find Device Location Instantly
⚫10 Maps can be Stored in Each Switch
⚫Other Feature same as Topology View
⚫To place and remove a device icon:
◼To select a device and click its icon from the device list.
◼The device icon will show on the floor image’s default location.
◼To click and hold left mouse by dragging-and-dropping the icon to the correct location on
the floor view.
◼To click cross sign on the right side of device icon to remove a device from all floor view
images.
Test01
Test01
Test02
Test02

10
Figure 14: The Device Icon to Remove a Device
⚫If there are more than two floor images, it can be selected from the field.
Figure 15: The Device Icon to Select floor
Test01
Test01
Test01
Test01

11
Map View
It can help to find the location of the devices even they are installed in different building. User
can place the device icon on the Map View of which navigated by Google map.
Figure 16: The Map View
⚫Anchor Devices onto Google Map.
⚫Find Devices Instantly from Map.
⚫On-Line Search Company/Address.
⚫Outdoor IP Cam/WiFi Applications.
⚫Other Feature same as Topology View.
Test02
Test02

12
Management
Device List
It will show all devices and their information which are detected by NTS.
Figure 17: The Devices List
A. If you want to auto-refresh the information then you need to
evoke the “Auto refresh”.
B. Click this icon to Refresh the status of all devices.
C. Click this icon to Edit Device Name and http Port.
⚫User can press “Edit” icon to edit device name for each IP device. This function can also be
configured in the Dashboard of Topology view.
⚫There is no HTTP connection function for Unknown Device and PC type devices, so UI
A
C
B
D
E

13
doesn’t provide “Edit HTTP port” function for configuring it.
Figure 18: The Edit of Devices List
D. Search devices by key words with full text search.
E. Only Offline devices provide “Remove” function to remove from NTS
device list.
Note:
The device name will not save until you click Apply button. Please do not click refresh, auto-
refresh or edit button before you apply new device name.

14
Maintenance
Floor Image
In this page, user can add or delete a floor image.
Figure 19: The Floor Image
⚫Each NTS switch provides 10 files space for uploading.
⚫Only support JPG and PNG formats.
⚫File size is limited to 256KB.
⚫All NTS switches’ floor image in the same network can be shared together.
◼For example:
If Switch1 has uploaded 10 floor images, Switch2 uploaded 5 images, the total 15
floor images can be shared and selected on all NTS switches in the same network.
⚫File name will attach IP address to let user know the floor image is stored on which NTS
switch.

15
Traffic Monitor
In this page, user can see traffic results on every connected devices.
Figure 19: The Traffic Image