Agilent Technologies MX3000P User manual

MX3000P/MX3005P QPCR SYSTEM
INSTRUMENT QUALIFICATION β–ACTIN INSTALL PLATE INSTRUCTIONS
Plate Storage and Handling Instructions
The plate is shipped on dry ice. Store at –20°C upon receipt. Do not remove the foil wrapper until immediately
before performing the run.
Wear chemical-resistant powder-free gloves whenever handling the qualification plate. This will ensure that no
finger oils or other debris are transferred to the optical seal.
Preparing for the Qualification Test
Note The Mx3000P or Mx3005P instrument and MxPro software must be set up, according to the
instructions in the system Setup and User’s Guide, prior to running the Qualification Test.
The the Qualification Test requires filter gain settings of ×8 for FAM and ×1 for ROX as per factory
settings. To check and modify the filter gain settings, click Instrument > Filter Set Gain Settings.
Just before starting the Instrument Qualification Test run, thaw the plate at room temperature for
15–30 minutes, leaving the plate sealed in the foil wrapper while thawing.
After thawing, remove the foil wrapper and then mix the contents of the wells by completing the following
actions five times:
•Invert the plate. Use a sharp, swift, downward motion to move the liquid to the seal on top of each well.
Observe the liquid to verify that the liquid has moved from the bottoms to the tops of the tubes.
•Re-invert the plate, and use the same motion to return the liquid to the bottom of each well, again verifying
liquid movement before proceeding.
After completing five mixing cycles, collect the liquid at the bottom of the wells. Brief centrifugation of the
plate at 1000 rpm is highly recommended, in order to dislodge any bubbles and to collect the liquid.
If a plate centrifuge is not available, shake the liquid down to the bottom of the tubes (using the same motion
described above for mixing). Shake-down the plate until the majority of the liquid is at the bottom of the tube
and only minimal amounts of liquid are retained on the tube seal or sides. It is important to shake-down any
noticeable liquid on the tube seal (e.g. visible semi-circles or crescent shapes). Small amounts of liquid spray
retained on the tube sides should not affect the test results.
Prior to loading the plate, verify that no bubbles are present at the bottoms of the tubes, beneath the liquid.
While it is critical to remove any bubbles from the bottom of the tubes, small bubbles near the liquid meniscus
should not affect the test results.
Important Bubbles trapped at the bottom of the tubes will interfere with fluorescence readings, invalidating
the test.

Mx3000P or Mx3005P Instrument Qualification β–Actin Install Plate Instructions
600567-11, Revision C
Performing the Qualification Test Run
The first time the MxPro software is opened using an instrument-connected computer, the software provides a
prompt to run the Instrument Qualification Test. The test may also be initiated by selecting Qualification Test
from the Instrument menu. The software automatically loads the plate set-up and thermal profile for the
qualification run.
A validation protocol Wizard will provide instructions in a series of dialog boxes before, during, and after the
run. Since the Qualification Test is a fixed test, only the actions directed by the validation protocol Wizard can
be completed. Do not attempt to modify the Qualification Test experiment or to analyze data during the
Qualification Test run.
First, the Instrument Qualification Test-Start dialog opens. When the plate has been prepared for the run, click
Next to open the Instrument Qualification Test-Start Run dialog box. Enter any comments for the
qualification test. Verify that the Perfect Fit frame shipped with the instrument has been removed from the
thermal block area. Load the test plate in the thermal block, verifying the correct orientation
(well A1 in the top, left corner). Close the instrument door, and then select Start Run. The Mx3000P or
Mx3005P instrument will begin the Instrument Qualification Test run. If the Pre-Run Lamp Warm Up dialog
box appears, select Run Now.
Important While the Qualification Test experiment is running, do not open the instrument door or cancel
the run.
Data Analysis
When run is complete, the software will proceed to the Analysis-Text Report section and the Instrument
Qualification Test-Run Complete dialog box will appear. Select Analyze. The software will open the
Microsoft Excel Instrument Qualification Validation template and export the Text Report data into the template.
Notes If a
Server Busy error dialog box appears, click Retry until the data export succeeds.
If any Norton anti-virus dialog boxes appear, select Notify again in 1 Day, and close the dialog.
Qualification Validation
The Microsoft Excel Validation template will open to the FAM analysis tab. Verify that the Data Count cell
reports the result Good to ensure that all of the data has been correctly exported into Excel. Next, verify that the
Result cell reports a Pass result. A Pass result indicates that the instrument is working properly. In this case, it
is not necessary to E-mail the data to Technical Services.
If the test reports a Check result, it is important to call Technical Services and send the three data files,
including Customer Information.txt, into Technical Services by E-mail for troubleshooting guidance. Include the
name of your institution, a contact name, and the instrument serial number when sending the data to Technical
Services.
Instrument Qualification Completion
After checking the Microsoft Excel Validation template, go back into the MxPro software. For a test report
Check result only, the Instrument Qualification Test-E-mail Experiment dialog box will appear and present
the option to automatically E-mail the data or save the data to a disk to later E-mail the data to Technical
Services ([email protected]). Finally, the Instrument Qualification Test-Complete dialog box will appear,
indicating that the test is finished.
Technical Services
Telephone: To find worldwide support telephone
numbers visit www.genomics.agilent.com and click
Contact Us
Email: [e-mail]