AirLive WL-5460AP v2 User manual

1 WL5460AP v2 User’s Manual
Wireless Access Point
WL-5460AP v2
User’sManual

2 WL5460AP v2 User’s Manual
FCC Certifications
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and receiver.
yConnect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
yConsult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20cm
between the radiator and your body.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
All trademarks and brand names are the property of their respective proprietors.
Specifications are subject to change without prior notification.

3 WL5460AP v2 User’s Manual
Table of Content
Introduction 4
FEATURES........................................................................................................................................................................5
PARTS NAMES AND FUNCTIONS.......................................................................................................................................6
FACTORY DEFAULT SETTINGS.........................................................................................................................................8
WL-5460AP v2 8
Hardware Connection 9
Check the LEDs: 9
About the Wireless Operation Modes 10
ACCESS POINT MODE ....................................................................................................................................................11
CLIENT MODE (INFRASTRUCTURE)................................................................................................................................12
CLIENT MODE (AD-HOC)...............................................................................................................................................13
BRIDGE MODE...............................................................................................................................................................14
REPEATER MODE (WDS REPEATER /UNIVERSAL REPEATER) ..................................................................................15
WISP MODE (CLIENT ROUTER /WISP+UNIVERSAL REPEATER)..............................................................................16
Configuration 17
LOGIN............................................................................................................................................................................17
MODE............................................................................................................................................................................18
AP Mode setting 19
Security 20
Advanced Settings 26
Access Control 29
Client Mode Settings 30
Bridge Mode Settings 32
Repeater Mode Settings 34
WISP mode Setting 36
STATUS.........................................................................................................................................................................40
System 40
Statistics 42
Active Clients 42
TCP/IP.........................................................................................................................................................................43
OTHER ..........................................................................................................................................................................45
Upgrade Firmware 45
Reboot 45
Save/Reload Settings 45
Password 47

4 WL5460AP v2 User’s Manual
INTRODUCTION
WL-5460APv2 is world's most popular multi-function access point. It features an impressive total of 7
wireless multi-function modes that are not available in normal access point. In addition, the ACK timeout
and RSSI feature makes it suitable for long distance application. From ordinary AP application to Hotspot
and WISP usage, you will find the WL-5460AP is the device you want.
WL-5460APv2 is an IEEE802.11b/g compliant 11 Mbps & 54 Mbps Ethernet Wireless Access Point. The
Wireless Access Point is equipped with two 10/100 M Auto-sensing Ethernet ports for connecting to LAN and
also for cascading to next Wireless Access Point.
WL-5460APv2 provides 64/128bit WEP encryption, WPA and IEEE802.1x which ensures a high level of
security to protect users’ data and privacy. The MAC Address filter prevents the unauthorized MAC
Addresses from accessing your Wireless LAN. Your network security is therefore double assured.
The web-based management utility is provided for easy configuration that your wireless network connection is
ensured to be always solid and hassle free.

5 WL5460AP v2 User’s Manual
Features
1. 2x100Mbps LAN ports for Wireless AP cascade.,2MB flash,16MB SDRAM
2. 18dBm output Power
3. AP ,Bridge,client ,WDS Repeater, Universal Repeater mode.
4. WISP Client Router,WISP+ Universal Repeater mode
5. 802.1x WPA
6. Support data rate automatic fallback.
7. Automatic channel selection.
8. Client access control.
9. Support 802.1x/Radius client with EAP-TLS, TKIP, AES encryption.
10. Support IAPP.
11. Adjustable Tx power, Tx rate, and SSID broadcast.
12. ACK Timeout , Watch dog function.
13. Allow WEP 64/128 bit.
14. Web interface management.
15. Support System event log and statistics.
16. MAC filtering (For wireless only).

Parts Names and Functions
1. Front Panel: (LED Indicators) (5460AP / 5460AP v2)
LED Status
Indicator Color Solid Flashing
1 Power Green Turns solid green when power is
applied to this device.
N/A.
2 Status Red
T
urns solid red when the device is
booting, after boot successfully,
the light turn off.
Link/Act. Green Turns solid green when connected
and associated to at least a client
station.
Receiving/
Sending data
WEP/WPA Orange Turns solid orange when wireless
security is enabled.
N/A
MAC Ctrl Orange Turns solid orange when MAC
Control is enabled.
N/A
3~6
Wireless
Bridge /
Repeater
Orange Turn solid orange when Bridge or
Repeater is enabled.
N/A
7LAN 1
8 LAN 2 Green Turns solid
green when linked to a
local network.
Receiving/
Sending data
Table 1: LED Indicators
6 WL5460AP v2 User’s Manual

2. Rear Panel: Connection Ports (5460AP / 5460AP v2)
Port/button Functions
A 12V DC Connects the power adapter plug
B LAN1 Connects to Ethernet
C LAN2 Connects to Ethernet
D (Factory)
RESET
Press over 3 seconds to reboot this device.
Press for over 10 seconds to restore factory settings.
Performing the Factory Reset will erase all previously
entered device settings.
Table 2: Connection Ports
7 WL5460AP v2 User’s Manual

8 WL5460AP v2 User’s Manual
Factory Default Settings
Setting Wireless Access Point
Device Name WL-5460AP v2
SSID Default value: airlive
Channel 13
WEP Default value: Disabled
IP Address 192.168.100. 252
DHCP Server zIn AP, Client, and Repeater Mode, the default DHCP Server is
OFF default . Please set your PC's IP to the same subnet as the
AP to access the AP
zIn WISP mode, the DHCP server is turned on. Please restart your
PC to renew the IP address.
DHCP Server IP Range 192.168.100.100~192.168.100.200

HARDWARE CONNECTION
Note: Before you starting hardware connection, you are advised to find an appropriate location to place the
Access Point. Usually, the best place for the Access Point is at the center of your wireless network, with line of
straight to all your wireless stations. Also, remember to adjust the antenna; usually the higher the antenna is
placed, the better will be the performance.
1. Connect to your local area network: connect a Ethernet cable to one of the Ethernet port
(LAN1 or LAN2) of this Wireless Access Point, and the other end to a hub, switch, router, or another
wireless access point.
2. Power on the device: connect the included AC power adapter to the Wireless Access Point’s power port
and the other end to a wall outlet.
Check the LEDs:
The Power and LAN # LEDs should be ON. LAN# LED will even blink if there is traffic.
The Link/Act LED will be on in static when associated with a station and blink whenever this AP receives data
packets in the air.
If the Status LED glows after self-test , it means this Wireless Access Point fails on self test. Please ask
your dealer for technical support.
3. Configure your PC: Make sure your local PC(s) has wireless network adapter installed.
9 WL5460AP v2 User’s Manual

10 WL5460AP v2 User’s Manual
ABOUT THE WIRELESS OPERATION MODES
The WL-5460AP v2 device provides all 7 modes of wireless operational applications with :
Access Point,
Bridge,
Client,
WDS Repeater,
Universal Repeater,
WISP (Client Router)
WISP + Universal Repeater
This device is shipped with configuration that is functional right out of the box. If you want to change the
settings in order to perform more advanced configuration or even change the mode of operation, you can use
the web-based utility provided by the manufacturer as described in the following sections.

Access Point Mode
When acting as an access point (default setting), this device connects all the stations (PC/notebook with
wireless network adapter) to a wired network. All stations can have the Internet access if only the Access
Point has the Internet connection. See the sample application below.
To set the operation mode to Access Point, please go to “Mode JAP” and click the “Setup” button.
11 WL5460AP v2 User’s Manual

Client Mode (Infrastructure)
If set to Client (Infrastructure) mode, this device can work like a wireless station when it’s connected to a
computer so that the computer can send packets from wired end to wireless interface.
Refer to the illustration below. This station (AP1 plus the connected computer 1) can associate to another
Access Point (AP2), and then can have the Internet access if the other Access Point (AP2) has the Internet
connection.
To set the operation mode to Client (Infrastructure), please go to “Mode JClient”, click the “Setup” button
in the “Network Type” field, select as “infrastructure” for configuration
12 WL5460AP v2 User’s Manual

Client Mode (Ad-hoc)
If set to the Client (Ad-hoc) mode, this device can work like a wireless station when it is connected to a
computer so that the computer can send packets from wired end to wireless interface. You can share files
and printers between wireless stations (PC and laptop with wireless network adapter installed).
See the sample application below.
To set the operation mode to Client (Ad-hoc), please go to “Mode JClient”, click the “Setup” button
in the “Network Type” field, select as “Ad-hoc” for configuration
13 WL5460AP v2 User’s Manual

Bridge Mode
In this mode, 2 access points in two remote locations connect to each other to provide a wireless bridge
between 2 remote LANs. It is mostly used by enterprise to connect 2 remote office's network together. The
bridge modes are connected by using either the WDS (Wireless Distribution System) or Adhoc topology
This feature is also useful when users want to bridge networks between buildings where it is impossible to
deploy network cable connections between these buildings.
To set the operation mode to Bridge, please go to “Mode JBrdige”, click the “Setup” button for
configuration
14 WL5460AP v2 User’s Manual

Repeater mode (WDS Repeater / Universal Repeater)
WDS Repeater mode
A repeater's function is to extend the wireless coverage of another wireless AP or router.
For WDS repeater to work, the remote wireless AP/Router must also support WDS function.
To set the operation mode to WDS Repeater, please go to “Mode JRepeater”, click the “Setup” button
in the “Network Type” field, select as “WDS Repeater ” for configuration
Universal Repeater mode
An universal repeater can also extend the wireless coverage of another wireless AP or router. But the
universal repeater does not require the remote device to have WDS function. Therefore, it can work with
almost any wireless device.
To set the operation mode to WDS Repeater, please go to “Mode JRepeater”, click the “Setup” button
in the “Network Type” field, select as “Universal Repeater ” for configuration
Note: When you are using the universal repeater mode, please make sure the remote AP/Router ‘s
WDS function is turned off..
15 WL5460AP v2 User’s Manual

WISP mode ( Client Router / WISP+Universal Repeater)
WISP (Client Router) mode
In WISP mode, the AP will behave just the same as the Client mode for wireless function. However, router
functions are added between the wireless WAN side and the Ethernet LAN side. Therefore, the WISP
subscriber can share the WISP connection without the need for extra router.
To set the operation mode to WISP mode, please go to “Mode JWISP”, click the “Setup” button
for configuration
WISP + Universal Repeater mode
In this mode, the AP behaves virtually the same as the WISP mode, except one thing: the AP can also send
wireless signal to the LAN side. That means the AP can connect with the remote WISP AP and the indoor
wireless card, and then provide IP sharing capability all at the same time! However, the output power is
divided between 2 wireless side and proper antenna installation can influence the performance greatly.
To set the operation mode to WISP mode, please go to “Mode JWISP”, click the “Setup” button
And select the Enable Universal Repeater Mode check box to enable this mode.
16 WL5460AP v2 User’s Manual

CONFIGURATION
Login
1. Start your computer. Connect an Ethernet cable between your computer and the Wireless
Access Point.
2. Make sure your wired station is set to the same subnet as the Wireless Access Point, i.e.
192.168.100.252
3. Start your WEB browser. In the Address box, enter the following:
http://192.168.100.252
The configuration menu is divided into four categories:
Mode, Status, TCP/IP, and Other .
Click on the desired setup item to expand the page in the main navigation page. The setup
pages covered in this utility are described below.
17 WL5460AP v2 User’s Manual

Mode
You can choose and setup different wireless mode and for detail configurations
Wireless Mode
AP Select the AP and press Setup button for Wireless AP mode
configuration
Client Select the Client and press Setup button for Wireless Client mode
configuration
Bridge Select the Bridge and press Setup button for Wireless Bridge mode
configuration
Repeater Select the Repeater and press Setup button for WDS Repeater and
Universal Repeater mode configuration
WISP Select the WISP and press Setup button for WISP (Client Router) and
WISP+ Universal Repeater configuration
18 WL5460AP v2 User’s Manual

AP Mode setting
et the alias name for this device. limited not exceed 32
characters
Alias Name You can s
Disable Wireless
face
Check the box to disable the Wireless LAN Interface, by so doing, you
won’t be able to make wireless connection with this Access PointLAN Inter in the
network you are located. In other words, this device will not be visible by
any wireless station.
Ba
1g supported rate only.
nd You can choose one mode of the following you need.
~2.4GHz (B): 802.11b supported rate only.
~2.4GHz (G): 802.1
~2.4GHz (B+G): 802.11b supported rate and 802.11g supported rate.
The default is 2.4GHz (B+G) mode.
SSID er; therefore, all accessThe SSID differentiates one WLAN from anoth
points and all devices attempting to connect to a specific WLAN must use
the same SSID. It is case-sensitive and must not exceed 32 characters. A
device will not be permitted to join the BSS unless it can provide the
unique SSID. An SSID is also referred to as a network name because
essentially it is a name that identifies a wireless network.
19 WL5460AP v2 User’s Manual

Channel Number
ve Wireless
Allow user to set the channel manually or automatically.
If set channel manually, just select the channel you want to specify.
If “Auto” is selected, user can set the channel range to ha
Access Point automatically survey and choose the channel with best
situation for communication.
The number of channels supported depends on the region of this Access
Point. All stations communicating with the Access Point must use the same
channel.
Security Press the setup button for detail configurations
To provide a certain level of security, the IEEE 802.11 standard has defined two types of
authentication methods: Open System or Shared Key. And WL-5460APv2 also support other
w
With Open System authentication, a wireless PC can join any network and receive any messages
ireless authentication and encryption methods for enhance your wireless network.
that are not encrypted. With Shared Key authentication, only those PCs that possess the correct
authentication key can join the network. By default, IEEE 802.11 wireless devices operate in an
Open System network and None data encryption. If you want secure your wireless network
you need to setup wireless security related function to enable security network.
20 WL5460AP v2 User’s Manual