AirLive WLA-5200AP User manual

WLA-5200AP
802.11a/b/g Multi-function Wireless Access Point
User’s Manual

FCC Certifications
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and receiver.
yConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
yConsult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may
cause undesired operation.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20cm between the radiator and your body.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
All trademarks and brand names are the property of their respective proprietors.
Specifications are subject to change without prior notification.

Table of Content
Introduction ............................................................................................................................ 1
FEATURES............................................................................................................................. 1
APPLICATION ........................................................................................................................ 2
PARTS NAMES AND FUNCTIONS........................................................................................... 3
Hardware Connection............................................................................................................ 5
About the WirEless Operation Modes.................................................................................. 6
AP MODE ............................................................................................................................. 6
CLIENT MODE (INFRASTRUCTURE)...................................................................................... 7
CLIENT MODE (AD-HOC)...................................................................................................... 7
BRIDGE MODE ...................................................................................................................... 8
REPEATER (WDS REPEATER/UNIVERSAL REPEATER)...................................................... 9
WISP (CLIENT ROUTER)MODE ......................................................................................... 11
Configuration........................................................................................................................ 12
LOGIN.................................................................................................................................. 12
STATUS............................................................................................................................... 12
System........................................................................................................................... 13
Statistics........................................................................................................................ 13
Active Client.................................................................................................................. 14
WIRELESS MODE................................................................................................................ 14
Wireless mode.............................................................................................................. 14
AP modes...................................................................................................................... 15
Client Mode Settings ................................................................................................... 17
Advanced Settings (AP/ Client/WISP Mode)........................................................... 18
Security (AP/Client/WISP Mode)............................................................................... 21
Bridge Mode Setting....................................................................................................... 23
Advanced Settings (Bridge/Repeater Mode)........................................................... 24
Security (Bridge/Repeater Mode).............................................................................. 27
WDS Control................................................................................................................. 30
Repeater Mode Settings.................................................................................................. 31
Access Control (Repeater mode).............................................................................. 32
WISP mode Settings........................................................................................................ 34
TCP/IP............................................................................................................................... 38
Basic.............................................................................................................................. 38
OTHER ................................................................................................................................40
Upgrade Firmware....................................................................................................... 40
Backup/Restore Settings ............................................................................................ 40
Region Settings ............................................................................................................... 41
Password....................................................................................................................... 41
System Log................................................................................................................... 42

1 WLA-5200AP v2 User’s Manual
INTRODUCTION
AirLive WLA-5200AP is an IEEE802.11a/b/g compliant 11 Mbps & 54 Mbps
Ethernet Wireless Access Point. The Wireless Access Point is equipped with two
10/100 M Auto-sensing Ethernet ports for connecting to LAN and also for
cascading to next Wireless Access Point.
This Access Point provides 64/128bit WEP encryption, WPA and IEEE802.1x
which ensures a high level of security to protects users’ data and privacy. The
MAC Address filter prevents the unauthorized MAC Addresses from accessing
your Wireless LAN. Your network security is therefore double assured.
The web-based management utility is provided for easy configuration that your
wireless network connection is ensured to be always solid and hassle free.
Features
•Two LAN ports for Wireless AP cascade
•Support WPA-PSK and WPA2-PSK
6 Wireless mode support :
AP ,Bridge,client ,WDS Repeater, Universal Repeater mode
WISP (Client Router) mode
•Support data rate automatic fallback
•Automatic channel selection
•Client access control
•Support 802.1x/Radius client with, TKIP, AES and TKIP_AES encryption
•Support IAPP
•Adjustable Tx power, Tx rate, and SSID broadcast
•Allow WEP 64/128 bit
•Web interface management
•Support System event log and statistics
•MAC filtering (For wireless only)
•Support wireless 802.11 SNMP management
•WatchDog timer to warm boot system

Application
Example 1
Example 2
2 WLA-5200AP v2 User’s Manual

Parts Names and Functions
1. Front Panel: (LED Indicators)
LED Status
Indicator Color Solid Flashing
Power Yellow Turns solid green
when the power is
applied to this device.
N/A.
Yellow Turns solid Yellow
when the Ethernet
cable is connected
the LAN port.
Receiving/
Sending data
LAN1,
LAN2
Wireless Yellow Turns solid Yellow
when the power is
applied to this
device.
Receiving/
Sending data
Table 1: LED Indicators
2. Rear Panel: Connection Ports
3 WLA-5200AP v2 User’s Manual

Port/button Functions
Use standard LAN cables (RJ45 connectors) to
connect your PCs to these ports.
If required, any port can be connected to another
hub. Any LAN port will automatically function as
an "Uplink" port when necessary.
LAN ports
(LAN1,LAN2)
(Factory)
RESET Press over 3 seconds to reboot this device.
Press for over 10 seconds to restore factory
settings.
Performing the Factory Reset will erase all
previously entered device settings.
Connects the power adapter plug
12V DC
Table 2: Connection Ports
4 WLA-5200AP v2 User’s Manual

HARDWARE CONNECTION
Note: Before you starting hardware connection, you are advised to find an
appropriate location to place the Access Point. Usually, the best place for the
Access Point is at the center of your wireless network, with line of straight to all
your wireless stations. Also, remember to adjust the antenna; usually the higher
the antenna is placed, the better will be the performance.
1. Connect to your local area network: connect a Ethernet cable to one of
the Ethernet port (LAN1,or LAN2) of this Wireless Access Point, and the
other end to a hub, switch, router, or another wireless access point.
2. Power on the device: connect the included AC power adapter to the
Wireless Access Point’s power port and the other end to a wall outlet.
3. Configure your PC: Make sure your local PC(s) has wireless network
adapter(s) installed.
5 WLA-5200AP v2 User’s Manual

ABOUT THE WIRELESS OPERATION MODES
This device provides seven operational applications with AP, Bridge,
Client (Ad-hoc), Client (Infrastructure) ,WDS Repeater, Universal Repeater ,
WISP(Client Router) mode which are mutually exclusive.
This device is shipped with configuration that is functional right out of the box. If
you want to change the settings in order to perform more advanced configuration
or even change the mode of operation, you can use the web-based utility
provided by the manufacturer as described in the following sections.
AP Mode
When acting as an access point, this device connects all the stations
(PC/notebook with wireless network adapter) to a wired network. All stations can
have the Internet access if only the Access Point has the Internet connection.
To set the operation mode to Access Point, please go to “Wireless JBasic
Settings”, in the “Mode” field click the down arrow bto select AP mode.
6 WLA-5200AP v2 User’s Manual

Client Mode (Infrastructure)
If set to Client (Infrastructure) mode, this device can work like a wireless station
when it’s connected to a computer so that the computer can send packets from
wired end to wireless interface.
To set the operation mode to Client (Infrastructure), please go to “Wireless
JBasic Settings”, in the “Mode” field click the down arrow bto select Client
mode, and then select “Network Type” as “Infrastructure”.
Client Mode (Ad-hoc)
If set to the Client (Ad-hoc) mode, this device can work like a wireless station
when it is connected to a computer so that the computer can send packets from
wired end to wireless interface. You can share files and printers between
wireless stations (PC and laptop with wireless network adapter installed).
To set the operation mode to Client (Ad-hoc), please go to “Wireless JBasic
Settings”, in the “Mode” field click the down arrow bto select Client mode, and
then select Network Type as “Ad-hoc”.
7 WLA-5200AP v2 User’s Manual

Bridge Mode
You will be able to connect two wireless LANs together under the Bridge mode.
This only works with another Wireless a/b/g Access Point. If enabled you must
enter the MAC address of that Wireless a/b/g Access Point.
To set the operation mode to Bridge mode, please go to “Wireless JBasic
Settings”, in the “Mode” field click the down arrow bto select Bridge mode.
8 WLA-5200AP v2 User’s Manual

Repeater (WDS Repeater/ Universal Repeater)
WDS Repeater mode
A repeater's function is to extend the wireless coverage of another wireless AP or
router.
For WDS repeater to work, the remote wireless AP/Router must also support
WDS function.
To set the operation mode to WDS Repeater, please go to “Mode JRepeater”,
click the “Setup” button
in the “Network Type” field, select as “WDS Repeater ” for configuration
9 WLA-5200AP v2 User’s Manual

Universal Repeater mode
An universal repeater can also extend the wireless coverage of another wireless
AP or router. But the universal repeater does not require the remote device to
have WDS function. Therefore, it can work with almost any wireless device.
To set the operation mode to WDS Repeater, please go to “Mode JRepeater”,
click the “Setup” button
in the “Network Type” field, select as “Universal Repeater ” for configuration
Note: When you are using the universal repeater mode, please make sure the remote
AP/Router ‘s WDS function is turned off..
10 WLA-5200AP v2 User’s Manual

WISP (Client Router) mode
WISP (Client Router) mode
In WISP mode, the AP will behave just the same as the Client mode for wireless
function. However, router
functions are added between the wireless WAN side and the Ethernet LAN side.
Therefore, the WISP subscriber can share the WISP connection without the need
for extra router.
To set the operation mode to WISP mode, please go to “Mode JWISP”, click the
“Setup” button
for configuration
.
11 WLA-5200AP v2 User’s Manual

CONFIGURATION
Login
1. Start your computer. Connect an Ethernet cable between your computer and
the Wireless Access Point.
2. Make sure your wired station is set to the same subnet as the Wireless
Access Point, i.e. 192.168.1.254
3. Start your WEB browser. In the Address box, enter the following:
http://192.168.1.254
4. Enter airlive in the Username and password column when you are prompted
the login screen.
The configuration menu is divided into four categories: Status, Wireless,
TCP/IP, and Other settings. Click on the desired setup item to expand the
page in the main navigation page. The setup pages covered in this utility are
described below.
Status
In this screen, you can see the current settings and status of this Access
Point. You can change settings by selecting specific tab described in below.
12 WLA-5200AP v2 User’s Manual

System
System Shows the product model name.
Product Model The current version of the firmware installed in this
device.
Firmware Version
Shows the firmware date.
Firmware Date The SSID differentiates one WLAN from another,
therefore, all access points and all devices
attempting to connect to a specific WLAN must
use the same SSID. It is case-sensitive and must
not exceed 32 characters.
A
device will not be
permitted to join the BSS unless it can provide the
unique SSID. An SSID is also referred to as a
network name because essentially it is a name
that identifies a wireless network.
Loader Version
Shows the Rome driver version.
Rome Driver Version
Statistics
The Statistics table shows the packets sent/received over wireless and ethernet
LAN respectively.
13 WLA-5200AP v2 User’s Manual

Active Client
Shows the information of the devices that are currently associating with this
Wireless Access Point.
Wireless Mode
Wireless mode
This page includes all wireless mode settings and major parameters. When you
choose each wireless mode that will cause the device to reboot for the new
wireless mode take effect.
14 WLA-5200AP v2 User’s Manual

AP modes
The distinguishing name of this device, you may
change the default alias name by entering a new
one in this column.
Alias Name
Disable Wireless LAN
Interface Check the box to disable the Wireless LAN
Interface, by so doing, you won’t be able to
make wireless connection with this Access Point
15 WLA-5200AP v2 User’s Manual

16 WLA-5200AP v2 User’s Manual
in the network you are located. In other words,
this device will not be visible by any wireless
station.
Band Choose a mode from the pull-down list.
•11b/g mixed: Select to allow both
wireless-b and wireless-g devices on
the network.
•11B only: Select to allow only wireless-
B devices on the network.
•11G only: Select to allow only wireless-
G devices on the network.
•11A (indoor): Select to allow only
wireless-A devices on the indoor
network.
•11A (outdoor): Select to allow only
wireless-G devices on the network.
•11A (indoor): Select to allow only
wireless-A devices on the outdoor
network.
SSID The SSID differentiates one WLAN from another;
therefore, all access points and all devices
attempting to connect to a specific WLAN must
use the same SSID. It is case-sensitive and
must not exceed 32 characters. A device will not
be permitted to join the BSS unless it can
provide the unique SSID. An SSID is also
referred to as a network name because
essentially it is a name that identifies a wireless
network.
Channel Number Allow user to set the channel manually or
automatically.
If set channel manually, just select the channel
you want to specify.
If “Auto” is selected, user can set the channel
range to have Wireless Access Point
automatically survey and choose the channel
with best situation for communication.
The number of channels supported depends on
the region of this Access Point. All stations
communicating with the Access Point must use
the same channel.
Apply Changes Press to save the new settings on the
screen.
Reset Press to discard the data you have
entered since last time you press
Apply Change.

Client Mode Settings
The distinguishing name of this device, you may
change the default alias name by entering a new
one in this column.
Alias Name
Disable Wireless LAN
Interface Check the box to disable the Wireless LAN
Interface, by so doing, you won’t be able to
make wireless connection with this Access Point
in the network you are located. In other words,
this device will not be visible by any wireless
station.
Band
17 WLA-5200AP v2 User’s Manual
Choose a mode from the pull-down list.
•11b/g mixed: Select to allow both
wireless-b and wireless-g devices on
the network.
•11B only: Select to allow only wireless-
B devices on the network.
•11G only: Select to allow only wireless-
G devices on the network.
•11A (indoor): Select to allow only
wireless-A devices on the indoor
network.
•11A (outdoor): Select to allow only
wireless-G devices on the network.
•11A (indoor): Select to allow only
wireless-A devices on the outdoor