AJAX MotionProtect Jeweller User manual

MotionProtect Jeweller User Manual
Updated July 30, 2022
MotionProtect Jeweller is a wireless indoor motion detector. It can operate for
up to 5 years from a built-in battery, and monitors the area within a 12-meter
radius. MotionProtect ignores animals, while recognizing a human from the rst
step.
MotionProtect operates within the Ajax security system, connected to the
via the protected protocol. The communication range is up to 1700
meters in the line of sight. In addition, the detector can be used as a part of
third-party security central units via the or integration
modules.
The detector is set up via the for iOS, Android, macOS and Windows.
The system noties users of all events through push notications, SMS and
calls (if activated).
Functional Elements
hub
Jeweller
uartBridge ocBridge Plus
Ajax app
Buy MotionProtect Jeweller

Operating Principle
1. LED indicator.
2. Motion detector lens.
3. SmartBracket mounting panel. To remove the panel, slide it down.
4. Perforated part of the mounting panel. Necessary to trigger a tamper in
case of any attempt to detach the detector from the surface. Do not break it
off.
5. . Triggers when an attempt is made to detach the detector
from the surface or remove it from the mounting panel.
Tamper button
6. Device switch.
7. Detector QR code. Is used to connect the device to the Ajax security system.
00:00
00:12

MotionProtect Jeweller is a wireless motion detector. The detector can identify
intrusions by detecting moving objects with temperatures close to the human
body using IR sensors.
When an armed detector identies motion, it instantly sends an alarm to the
hub, activating the sirens connected to the system, triggering scenarios, and
notifying users and the security company. All MotionProtect alarms and events
are recorded in the event feed of the Ajax apps.
Users know where motion is detected. The notications contain the name of the
hub (protected facility), the name of the device, and the virtual room to which
the detector is assigned.
The detector doesn’t arm instantly. The time it takes to switch to armed mode depends
on exit delays (specied in the detector settings) and the hub–detector polling interval
(Jeweller or Jeweller/Fibra settings, the default value is 36 seconds). In the rst case,
the delay is set by an administrator or a PRO-user with administrator rights. In the
second case, the delay occurs because the hub takes one ping interval to notify the
detector about the transition to armed mode.
Pet immunity
When properly installed and congured, MotionProtect does not react to
animals up to 50 centimetres tall and weighing up to 20 kilograms.
How Ajax noties users of alerts
More about Ajax motion detectors

The detector must be installed at 2.4 meters without obstruction to its view. For
example, in a corner where the view will not be blocked by a closet or other
furniture on which a pet can climb.
It is also important to set the proper sensitivity in the :
When indoor motion detectors are installed below the recommended height,
animals move in the hypersensitive zone. The detector can raise the alarm if a
shepherd walks on its hind legs or even a tiny spaniel plays on a chair. The
detector will also raise the alarm if the animal can jump to the level of
MotionProtect or move near it.
Temperature compensation
The detector perceives people and other objects as heat spots. The device
monitors these heat spots and, if they move, detects an alarm. MotionProtect
reacts to the movement of heat spots whose temperature is close to the human
body.
detector settings
High — the detector does not react to cats (up to 25 cm tall).
Medium — it does not react to small dogs (up to 35 cm tall).
Low — it does not react to animals up to 50 cm tall.
Why detectors react to animals and how to avoid this
How to install MotionProtect correctly

When the ambient temperature is about the temperature of the human body, the
correct operation of the detector is not guaranteed unless temperature
compensation is applied. It is used in all Ajax motion detectors. MotionProtect
recognizes motion across the entire operating temperature range with
temperature compensation.
Sending events to the monitoring station
The Ajax security system can transmit alarms to the monitoring
app as well as the central monitoring station (CMS) in the formats of the Sur-
Gard protocol (Contact ID), SIA (DC-09), ADMECO 685, and other proprietary
protocols. A complete list of supported protocols is .
MotionProtect can transmit the following events:
When an alarm is received, the security company monitoring station operator
knows what happened and precisely where to send a fast response team on the
site. The addressability of Ajax devices allows sending events to the PRO
Desktop or the CMS the type of the device, its name, security group, and virtual
room. Note that the list of transmitted parameters may differ depending on the
kind of CMS and the selected protocol for communication with the monitoring
station.
The device ID and the loop (zone) number can be found in .
Learn more
PRO Desktop
available by the link
Which CMSs can the Ajax security system be connected to
1. Motion alarm.
2. Tamper alarm / restoration.
3. Loss / restoration of connection with the hub or radio signal range extender.
4. Temporary deactivation / activation of the detector.
5. Unsuccessful attempt to arm the security system (when
is enabled).
System Integrity
Check
device states in the Ajax app

Connecting to the security system
Before adding a device
Connecting to the hub
1. Install an .Ajax app
2. if you don’t have one. Add a compatible hub to the app,
make the necessary settings, and create at least one virtual room.
Create an account
3. Ensure that the hub is switched on and has Internet access via Ethernet, Wi-
Fi and/or mobile network. You can check the connection state in the Ajax
app or by looking at the hub LED indicator. It should light up white or green.
4. Ensure that the hub is disarmed and does not start updates by checking its
status in the Ajax app.
1. Open the Ajax app. If you have access to multiple hubs or using the PRO
app, select the hub where you want to add the detector.
2. Go to the Devices tab and click Add Device.
3. Name the detector, scan or type in the QR code (placed on the detector and
the package box), and select a room and a group (if is
enabled).
Group mode
4. Press Add.
5. Switch on the device.

If the connection fails, turn the detector off and try again in 5 seconds. Note that
if the maximum number of devices has already been added to the hub
( ), you will be notied when you try to add a new
one.
To connect MotionProtect to the hub, the detector must be located at the same
facility as the system (within the hub radio signal range). For the detector to
work via the radio signal range extender, you need rst add the detector and
range extender to the hub, then connect it to the range extender.
The detector connected to the hub will appear in the list of hub devices in the
Ajax app. Updating the statuses of devices in the list depends on the Jeweller or
Jeweller/Fibra settings; the default value is 36 seconds.
The hub and the device operating at different radio frequencies are incompatible. The
radio-frequency range of the device may vary by region. We recommend purchasing and
using Ajax devices in the same region. You can check the range of operating radio
frequencies with the
MotionProtect works with one hub. When connected to a new hub, the detector
stops sending events to the old one. When added to a new hub, the detector is
not removed from the device list of the old hub. This must be done through the
Ajax app.
Connecting to third party security systems
To connect the detector to a third party security central unit with the
or integration module, follow the recommendations in the
manuals of these devices.
depending on the hub model
technical support service
uartBridge
ocBridge Plus

Malfunctions
When a malfunction is detected (for example, there is no connection via
Jeweller), the Ajax app displays a malfunction counter on the device icon. All
malfunctions are shown in the detector states. Fields with malfunctions will be
highlighted in red.
A malfunction is displayed if:
Icons
The icons display some of the MotionProtect states. You can view them in the
Ajax app in the Devices tab.To access them:
Icon Meaning
Jeweller signal strength. Displays the signal strength between the detector and
hub or range extender. The recommended value is 2 or 3 bars.
The detector battery charge level.
The detector is operating via a .
The detector operates in the Always active mode.
The detector temperature is out of acceptable limits: below –10°C and
above +40°C.
The detector enclosure is open (tamper is triggered).
No connection with the hub or radio signal range extender via Jeweller.
The detector battery is low.
1. Sign in to the .Ajax app
2. Select the hub if you have several of them or using a PRO app.
3. Go to the Devices tab.
Learn more
Learn more
radio signal range extender

Entry delay is enabled.
Exit delay is enabled.
MotionProtect will arm in Night mode.
MotionProtect has detected motion. The icon is displayed when the detector is
armed
MotionProtect is temporarily disabled.
MotionProtect has been deactivated due to exceeding the preset number of
alarms.
MotionProtect has tamper triggering events temporarily deactivated.
States
The states include information about the device and its operating parameters.
The states of MotionProtect can be found in the Ajax app:
Parameter Value
Learn more
Learn more
Learn more
Learn more
Learn more
Learn more
Learn more
1. Go to the Devices tab.
2. Select MotionProtect from the list.

Temperature Detector temperature. It is measured on the
processor and changes gradually.
The acceptable measurement error between the
value in the app and the ambient temperature is
2°C.
The value is updated as soon as the detector
identies a temperature change of at least 1°C.
Jeweller Signal Strength
Signal strength between the detector and hub or
range extender on the Jeweller channel. The
recommended value is 2 or 3 bars.
Jeweller is a protocol for transmitting
MotionProtect events and alarms.
Battery Charge
Battery level of the device. Displayed as a
percentage.
When the batteries are low, the Ajax apps and
the security company will receive appropriate
notications.
After sending a low battery notication, the
detector can work for up to 2 months.
Lid
The status of the detector tamper that responds
to detachment or opening of the device
enclosure:
Delay When Entering, sec Delay time when entering: from 5 to 120
seconds.
How the battery charge is displayed
Battery life calculator
Open — the detector was removed from the
SmartBracket, or detector integrity was
compromised. Check the device.
Closed — the detector is installed on the
SmartBracket mounting panel. The integrity
of the device enclosure and the mounting
panel is not compromised—normal state.
Learn more