Allen + Roth BV-6333-48 User manual

ITEM #2694560
VANITY WITH TOP
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday. You
could also contact us at [e-mail] or visit www.lowespartsplus.com.
ATTACH YOUR RECEIPT HERE
ALLEN+ROTHand logo design are trademarks or
registered trademarks of LF, LLC. All rights reserved.
welcoming • sophisticated • inspiring
1
F
Model #BV-6333-48
SM20586

2
PACKAGE CONTENTS
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install this
product.
WARNING
•Keep small parts away from children.
•Installing the item will require more than one person.
CAUTION
•DO NOT try to pry off top from vanity. Damage to top or vanity may occur.
• Use care when assembling the vanity; take your time and follow the assembly instructions
closely.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
HARDWARE CONTENTS
Touch-Up Pen
Qty:1
迅
捷PDF
编辑器
PART DESCRIPTION QUANTITY
A Vanity 1
BTop (pre assembled
to Vanity (A))
1
CBacksplash 1
Optional Nickel Pull
Qty:5
A
B
C
AA BB

3
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
Estimated Installation Time: 20-30 minutes (24 hours for adhesive to dry).
Tools Required for Installation (not included): Silicone compound, Utility knife.
Step 1: Vanity Drawer Removal
1a. Open the preassembled drawer as far as possible.
INSTALLATION INSTRUCTIONS
1b .
Simultaneously press the plastic cards on the
bottom of drawer left side and right side inward.
1c. Once both plastic cards are held in the indicated
position, pull the drawer straight out.
1

4
INSTALLATION INSTRUCTIONS
2
3
3. To mount the backslash (C) to the wall, apply a thin
bead of silicone compound (not included) to the
unpolished back side and bottom of the backsplash
(C). Position backsplash (C) as shown onto vanity
top (B) and against the wall. Clean any excess
silicone compound before allowing it to dry.
2. In case of uneven floors, floor levelers are provided
at the bottom of the vanity. If necessary, adj ust floor
leveler by hand to correct tilting and/or level doors.
Step 2: Adjustable Level
Step 3: Backsplash Installation
B
C

5
4. Open the drawers, remove the preassembled
screws, change the optional nickel pulls and relock
the screws.
INSTALLATION INSTRUCTIONS
Optional Step 4: Replace hardwares
4
CARE AND MAINTENANCE
• Dust the vanity regularly with a soft, non-lint producing cloth or household dusting product.
• You can clean the vanity with a gentle, non-abrasive household cleaner.
• Make sure to dry the wood immediately with a soft cloth or towel.
• The engineered stone top surface is very sensitive to acid-alkaline liquids and materials,
such as toothpaste, hand soap, cologne, perfume, nail polish remover, hair color and perm products,
shampoo, drain and toilet bowl cleaner, alcohol, lemon juice, medications, etc. Please try to avoid
contact of these acid-alkaline liquids and materials with the vanity top surface when possible. If these
liquids or materials spill onto the surface, wipe it off immediately. Always clean the surface and keep it
dry after use.
• Tips for using touch-up pen (AA): For scratches, stroke in direction of scratch. Rub off excess colorant
promptly with a soft cloth.
WARRANTY
The manufacturer provides a one year limited warranty for residential use that the vanity combo will
be free from manufacturing defects, provided the original purchaser resides in or owns the home of
installation, and provided the vanity combo is installed and maintained according to the installation
and maintenance instructions contained within and supplied by the manufacturer. The liability will be
limited to cost of products only. This warranty is in lieu of any other express warranties. This warranty
applies only to the original purchaser. This warranty does not apply to any damage on the product by
accident, misuse, or modified,improper installation or by affixing accessories not produced by the
manufacturer. There is no further expressed warranty. The manufacturer shall not be legally
responsible for incidental, consequential or special damages arising at or in connection with product
use or performance except as may otherwise be accorded by law. The manufacturer disclaims any
and all implied warranties.

6
REPLACEMENT PARTS LIST
C
DEFG
For replacement parts, call our customer service department at 1-877-888-8225, 8 a.m. - 8 p.m.,
EST, Monday - Sunday. You could also contact us at [email protected] or visit
www.lowespartsplus.com.
Printed in Vietnam
ALLEN+ROTH and logo design are
registered trademark of LF, LLC. All
Rights Reserved.
AA BB CC

ARTÍCULO #2694560
7
F
SM20586
acogedor • sofisticado • inspirador
ALLEN+ ROTHy el diseño del logotipo son marcas
comerciales o marcas registradas de LF, LLC. Todos
los derechos reservados. TOCADOR CON
CUBIERTA
Modelo #BV-6333-48
Número de serie Fecha de compra
¿Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro
Departamento de Servicio al Cliente al 1-866-439-9800, de lunes a domingo de 8 a.m. a 8 p.m., hora
estándar del Este. También puede ponerse en contacto con nosotros en [e-mail] o
visitar www.lowespartsplus.com.
ADJUNTE SU RECIBO AQUÍ

8
迅
捷PDF
编辑器
A
B
C
CONTENIDO DELPAQUETE
ADITAMENTOS
Aplicador de retoque
Cant:1 Tirador de níquel opcional
Cant:5
INFORMACIÓN DE SEGURIDAD
Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar este
producto.
ADVERTENCIA
•Mantenga a los niños alejados de las piezas pequeñas.
•La instalación del artículo requiere más de una persona.
PRECAUCIÓN
•NO intente retirar la cubierta del tocador. Esto podría dañar la cubierta o el tocador.
•Tenga cuidado al ensamblar el tocador; tómese el tiempo necesario y siga las instrucciones de
ensamblaje detenidamente.
GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA.
AA BB

9
Antes de comenzar a ensamblar el producto, asegúrese de tener todas las piezas. Compare las
piezas con la lista del contenido del paquete y la lista de aditamentos. No intente ensamblar el
producto si falta alguna pieza o si estas están dañadas.
Tiempo de instalación estimado: 20 a 30 minutos (24 horas para que seque el adhesivo).
Herramientas necesarias para la instalación (no se incluyen): compuesto de silicona, cuchillo para
uso general.
PREPARACIÓN
INSTRUCCIONES DE INSTALACIÓN
1a. Abra la gaveta preensamblada lo máximo que sea
posible.
1b. Presione simultáneamente las tarjetas de plástico
en la parte inferior de la gaveta del lado izquierdo
y del lado derecho hacia adentro.
1c. Después de sostener ambas tarjetas de plástico
en la posición indicada, jale y retire la gaveta.
Paso 1: retiro de la gaveta del tocador
1

10
3
B
C
INSTRUCCIONES DE INSTALACIÓN
Paso 2: nivel ajustable
Paso 3: instalación del protector contra salpicaduras
2. En caso de que el piso estédesnivelado, se
incluyen niveladores para piso en la parte inferior
del tocador. Si es necesario, ajuste el nivelador
de forma manual para corregir la inclinación o
nivelar las puertas.
3. Para montar el protector contra salpicaduras
(C) en la pared, aplique un cordón delgado de
compuesto de silicona (no se incluye) en la parte
posterior sin pulir y en la parte inferior del protector
contra salpicaduras (C). Coloque el protector contra
salpicaduras (C) como se muestra, sobre la
cubierta de tocador (B) y pegado a la pared. Limpie
todo exceso de compuesto de silicona antes de
dejar secar.
2