Altrad LIV MLZ NG Series User manual

CONCRETE MIXER ASSEMBLY INSTRUCTIONS
1. Mount the wheels (6) on the lower frame (5) and secure them with axle protection (7);
2. Attach the foot (1) to the upper frame (8) with the screw (2), washer (4) and nut (3 );
3. Tighten both screws (2);
4. Take the drum and girder set (22) and insert it to the upper frame (8);
5. Insert the screws (20) and washers (21) through the girder set, as shown on the picture, and fasten
them (loosely);
6. Attach the clamp (24) to the upper frame ;
7. Insert the screw (14) through the clamp and fasten the safety nut (15);
8. Insert the spring (23) as shown in picture 8;
9. Attach the steering wheel/handle (9)/(10) as shown in picture 9;
10. Insert the screw (13) through the steering wheel/handle and attach the nut (12);
11. Put the cogwheel (26) on the bottom part of the drum (22);
12. Combine the drum upper part (29) with the drum bottom part and align the holes;
13. Insert screws (28) through the cogwheel, fasten them with the washer (27) and nut (17) (loosely) and
rotate the drum;
14. Align the cogwheel with a hammer so that you achieve steady circular run and fasten the screws on
the cogwheel tightly;
15. Attach the left and right protector (19) as shown on the picture 15;
16. Fasten the left and right protector with the screw (18) ;
17. Put the engine housing (30) on the frame as shown in picture 17;
18. Insert the screws (14), washers (16) and nuts (17) and fasten them (loosely);
19. Insert the first fillet (32) on the axle;
20. Insert the pulley (31) on the axle as shown on the picture 20;
21. Insert the second fillet (32) on the axle and put the belt on the pulley;
22. Press down the engine housing with the force of approx. 30 kg and finally tighten the screws as shown
on picture 22;
23. Attach the engine housing lid (33) on the housing and fasten it with screws (34)
24. Attach the mixing shovels (25) into the drums predrilled holes;
25. Fasten the mixing shovels with screws (20), washers (21) and nuts (17).
26. Congratulations –the mixer is assembled and ready for use.
1
64117 - FOOT
18
50648 - SCREW 5 X 14 ZN
2
92129 - SCREW M10 X 70
19
80717 - PROTECTOR L + R
3
13368 - NUT M10
20
80713 - SCREW M10 X 25
4
10236 - WASHER A10
21
80710 - SAFETY NUT M10
5
92341 - LOWER FRAME
22
DRUM AND GIRGER SET
6
80218 - WHEEL
23
64040 - SPRING
7
96532 - AXLE PROTECTION Ø20
24
64062 - CLAMP
8
66116 - UPPER FRAME
25
80732 - MIXING SHOWELS
9
80242 - HAND WHEEL
26
92840 - COGWHEEL
10
80062 - BELT
27
11981 - WASHER A8
11
80201 - SCREW M8 X 16
28
24461 - SCREWS M8 X 25
12
21140 - NUT M12
29
80495 - DRUM UPPER PART
13
69094 - SCREW M12 X 45
30
80755 - ELECTRICAL MOTOR
14
10136 - SCREW M8 X 70
31
50691 - PULLEY
15
25898 - SAFETY NUT M8
32
10698 - FILLET Z20
16
46352 - WASHER A8 –WIDE
33
50690 - ENGINE HOUSING LID
17
13367 - NUT M8
34
50684 - SCREW PT 5 X 14