Amana C-Model Assembly instructions

A IR C ONDITIONERS
& H EAT P UMPS
Don’t settle
for less than the
Amana Standard Advantage
Featuring the most energy efficient
heat pump ever built by Amana
P ACKAGE
T ERMINAL
P ACKAGE
T ERMINAL
Heating ®
&Air Conditioning
Comfort. Quality. Trust.st.

C - 2
THEAMANA“STANDARD”ADVANTAGE
Amanahas designedthePackagedTerminalAirConditionerforcustomercomfortandownerpeaceofmind. Noother
unitintheindustryofferssomany“extras”alreadybuiltinas“STANDARD”onevery unit. Withallthefeaturesandbenefits
our units have to offer, you no longer need to settle for anything less than the Amana “Standard” Advantage!!
C-MODEL
C-MODEL
Standard Features Advantages and Benefits
Five-Year Warranty Enjoy one of the most comprehensive warranties in the industry. Full 1-year warranty on unit parts and labor;
full 5-year warranty on the entire sealed system components; limited 2nd through 5th year parts-only warranty
on functional components. See back of this brochure for details.
Energy Efficiencies Our units' high efficiencies can qualify you for many of the rebates offered by electrical power companies
EER’s up to 11.6 and heat pump COP’s up to 3.3 keep energy consumption to a minimum.
Freeze
Protection
No more worries about bursting water pipes or broken fixtures caused by freezing temperatures. When the
unit senses temperatures of 40 degrees Fahrenheit or below, the unit activates the fan motor, and either
the electric resistance heater or the hydronic heater.
7" Unit Front Enhance valuable room space--the unit front has a sleek 7" depth, one of the shallowest silhouettes in the
industry today. In addition, to inhibit guest-tampering, the front can be secured to the chassis with hidden screws.
Versatile Style Our unit's stylish design and neutral color make it compatible with virtually any room décor or
architectural design. The unit becomes less noticeable as it blends into the room's color scheme.
Easy To Use Controls No complex controls to confuse your guests and create phone calls for your manager. Controls are easy
to read, understand, and activate.
Remote Thermostat
Control
Each unit is built to be operated from a remote-mounted thermostat, if desired. Even if you start without
a remote, you can take advantage of a built-in low voltage power source which accommodates a variety
of manufaturer approved thermostat choices --manual, auto change-over, or programmable -- at a later date.
Increased
Dehumidification
Capacity
Maintain lower humidity levels in rooms while cooling them without the need for expensive add-on’s.
As a result, guests feel more comfortable at higher temperatures, thus reducing cooling costs, and increasing the life
of your furniture, wall coverings, and fixtures is extended which means less replacement costs.
Quiet Operation The unit's state of the art design and construction provide a quiet environment allowing guests to enjoy peaceful,
sleep-filled nights. Operating sound levels are further dampened when unit is in "low fan" mode of operation.
Front Desk Control Obtain greater savings by centrally controlling units and eliminate wasted energy generated by cooling
and heating unoccupied rooms. Each unit has low voltage interface capability with a field supplied
front desk ON/OFF switch.
Remote Temperature
Sensing Guests enjoy ultimate comfort with consistent climate control. When the field installed thermister(RTS02) is used,
the unit mounted thermostat is overridden to allow more accurate, internal wall-sensing of room ambient temperature.
Thirty
Second
Fan Off Delay
Fan continues to run thirty (30) seconds after compressor has stopped in either cooling or heat pump mode
and after electric heat has been turned off. This improves efficiency by dispersing the conditioned air on the coils
into the room.
Compressor
Lock-In
This feature helps prolong the life of the compressor by preventing short-cycling. When the compressor is
switched from off to on because room temperature has risen or fallen below the specified limit, it will remain on
for at least four minutes. If the temperature set point is changed during this four minutes, the lock-in feature
is overriden.
Condensate
Dispersion System
The Amana condensate dispersion system removes condensate from indoor cooling operation by throwing water directly
on to the outdoor coil for rapid evaporation and increased cooling efficiencies. The slinger ring on the fan blade draws
water up and into fan blade. This water is then atomized and evaporated into the atmosphere
through the condenser.
Automatic
Emergency Heat
No more "my unit is not heating" complaints during the middle of the night. Heat pump units will automatically switch over
to electric resistance heat if for any reason the heat pump compressor system fails or if the heating load is greater than
the unit capacity.
Extended
Heat Pump Heating The heat pump models will operate in the heat pump heating mode down to as low as 24°F outdoor ambient, providing
additional hours of energy saving operation.

C - 3
THE AMANA“STANDARD”ADVANTAGE
Easy Filter Access
Maintainingtheunit’seffi-
ciency while saving time and
money is as easy as 1-2-3.
The filter is easily accessed for
cleaningorreplacement
withoutremovingtheunitfront.
All units come with factory installed power cords.
(Field Supplied)
Step 1: Open the intake grille
Step 2: Pull open the intake grille
Power Cord Plugs
250V Rating Power Cord Plugs
NEMA 6 Configuration
G
W
30 amp
277V Rating Power Cord Plugs
NEMA 7 Configuration
G
W
20 amp
15 amp 20 amp 30 amp
Power Receptacle Configuration
G
G
G
NEMA6-15R; 250V receptacle,
used on 230/208V units
NEMA6-20R; 250V receptacle,
used on 230/208V units
NEMA6-30R; 250V receptacle,
used on 230/208V units
G
W
NEMA7-20R; 277V receptacle,
used on 265V units
GNEMA7-30R; 277V receptacle,
used on 265V units
Step 3: Press down lightly on the thumb tab
at the top of the filter and remove the filter.
Optional Accessory Advantages and Benefits
Wall Sleeve
13-3/4" x 42" x16-1/16"
No more worries about changing out non-standard sleeves that do not accommodate the bulk of what the
industry has to offer. Amana's wall sleeve is an industry standard size of 13-3/4" deep x 42" wide x 16-1/16"
high. (Please Note: Wall Sleeve must be ordered separately.)
C-MODEL
C-MODEL
Standard Features Advantages and Benefits
Fan
Sampling
(SBS Routine)
Imagine a uniformly maintained temperature throughout the room without constant adjustment of the thermostat. During
the "fan-auto" mode, starting at 5 minute then increasing up to 15-minute intervals, the fan automatically samples the air
inside the room. If the air is too warm, the unit will automatically cycle into the cooling mode
without thermostat adjustment. This feature for cooling only.
Fan Mode
Switch Take advantage of each unit's dual options: select continuous fan operation or cycle the fan ON and OFF with
the thermostat.
Easy
to Service
& LED Diagnostics
The main components are easily serviced and there is no guessing to determine the problem with our
easy-to-read diagnostics. For example: 2 blinks indicate a blown or missing fuse while 1 blink every
5 seconds means the board is operating correctly. This diagnostic light is visible by removing the front cover.
Available Filtered
Ventilation Air Guest's rooms stay cleaner, longer. The ventilation air intake filters outside air to reduce dust and other airborne
material. The control lever is hidden from occupant's view.
Zero Floor Clearance Unit can be installed flush to the finished floor, if desired. (Some accessories do not have zero clearance).
Electronic
Temperature
Limiter
Save energy and money by avoiding the extreme settings that can occur with guest operation. The temperature
limiter allows you to adjust in-room temperature settings within any of 4 pre-programmed
ranges set by you with easy to use dip switches.
Random Restart Avoid troublesome power surges that can damage electrical circuits. Each unit has a random restart circuit to prevent
all units from restarting at one time after power disruption. Random restart occurs in 2-4 minutes.
Compressor Restart
Delay Extended compressor-life. The unit automatically delays any restart attempt by three minutes to allow the
refrigerant pressures time to equalize.
Reduced
Outdoor
Sound Transmission
With our STC (Sound Transmission Coefficent) rating of 27, we keep outdoor sounds out-of-doors. By installing
the optional STC30 Rating Accessory Kit, ratings can be increased to STC 30, thereby meeting or exceeding
most ratings requirements. (Kit ordered separately.)

C - 4
SPECIFICATIONS
**PTC/H09*A50*Cis2-stage;PTC/H12*A50*C andPTC/H15*A50*Care1-stage.
Hydronic Heat Models
Hydronic Models / Hot Water & Steam Heating
These special models are shipped without a chassis front,
withoutelectricheat, and havean additional relay and40VA
transformerfor wateror steam valve operation. Also avail-
ableinHydronic with Powered VentandHydronic with Pow-
eredDoor. See ModelIdentification (right) for Special Fea-
tureCodesfor these models. SeeC-7forhydronicaccesso-
ries. Hydronic with Manual Door
* Approximately 95 CFM with optional power vent kit. Actual vent CFM performance will vary due to application and installation conditions.
Electric Heater Performance (PTC and PTH Models)
(Primary Heating for PTC models; Auxiliary Heating for PTH models)
ELECTRIC NOMINAL HEATING TOTAL TOTAL MIN. CIRCUIT OVERCURRENT
VOLTAGE HEATER NO. OF BTUH BTUH BTUH WATTS AMPS AMPACITY PROTECTION POWER
SIZE (kW) STAGES AT 230V AT 208V AT 265V (NOTE 6) (NOTE 8) (NOTE 2) (NOTE 4) CORD
230/208V 2.5/2.0 18,500 6,800 - - 2,650/2,140 11.5/10.2 14.2 15 6 - 15 P
230/208V 3.5/2.9 112,000 9,900 - - 3,650/3,040 15.8/14.5 19.6 20 6 - 20 P
230/208V 5.0/4.1 ** 17,100 14,000 - - 5,150/4,240 22.3/20.3 27.7 30 6 - 30 P
265V 2.5 1- - - - 8,500 2,650 10.0 12.4 15 7 - 20 P
265V 3.7 1- - - - 12,600 3,850 14.6 18.1 20 7 - 20 P
265V 5.0 ** - - - - 17,100 5,150 19.5 24.2 25 7 - 30 P
PTCModels
Model Number Voltage
Capacity Cooling Capacity EER
PTC093A00HC 230/208 9,100 / 8,900 11.3
PTC123A00HC 230/208 12,000 / 11,900 10.7
PTC153A00HC 230/208 14,200/14,000 9.2
PTC094A00HC 265 9,100 11.3
PTC124A00HC 265 12,200 10.7
PTC154A00HC 265 14,200 9.3
Cooling Performance
Model (Basic) (NOTES 1, 7 & 9) PTC073A**AC PTC074A**AC PTC093A**AC PTC094A**AC PTC123A**AC PTC124A**AC PTC153A**AC PTC154A**AC
Voltage (NOTES 1 & 3) 230/208 265 230/208 265 230/208 265 230/208 265
Capacity (BTUH) 7,100 / 7,000 7,100 9,100/8,900 9,100 12,000 / 11,900 12,000 14,200 / 14,000 14,200
Amps 2.8/3.0 2.3 3.7/3.8 3.0 4.6/5.0 4.3 6.3 / 6.9 5.9
Watts 610 / 600 610 805 / 785 805 1,120 / 1,110 1,130 1545 /1520 1,525
EER 11.6 11.6 11.3 11.3 10.7 10.7 9.2 9.3
Unit without Electric Heater
Min.Circuit Ampacity
(NOTES 2 & 4) 4.0 3.6 5.1 4.4 6.4 5.7 8.4 7.4
245 / 240 245 245 / 240 245 325 / 315 325 325/315 325
Low 220 / 205 220 220 / 205 220 250 / 229 250 250/220 250
265 / 260 265 265 / 260 265 345 / 335 345 345/335 345
Low 230 / 215 230 230 / 215 230 265 / 235 265 265/235 265
Ventilated Air, CFM (Fan Only)* 65* 65* 65* 65* 70* 70* 70* 70*
Ventilated Air, CFM (Compressor & Fan)* 65* 65* 65* 65* 70* 70* 70* 70*
Dehumidification (Pints/Hr.) 1.6 1.6 2.6 2.6 3.5 3.5 4.4 4.4
Net Weight (approximate Lbs.) 90 90 95 95 105 105 110 110
Shipping Weight (approximate lbs.) 105 105 110 110 120 120 125 125
CFM (Cool, Wet Coil) High
CFM (Dry Coil) High
COOLING/ELECTRICHEAT
AMANA C-MODEL
AMANA C-MODEL
PT C09 3A35 A C
ENGINEERING
PACKAGE
DESIGN LEVEL
TERMINAL
(A - C)
MODEL TYPE
SPECIAL FEATURE CODE
C = COOLER A = Standard Model
H = HEAT PUMP
MAJOR
B = Power Vent
DESIGN
C = Seacoast Model
NOMINAL
SERIES
D = Cond. Disposal Pump
COOLING CAPACITY
F = Hydronic w/Power Vent & Door
(BTUH)
G = Hydronic w/Power Door
07 = 7,000 Btuh H = Hydronic w/Manual Door
09 = 9,000 Btuh J = Power Door
12 = 12,000 Btuh K = Cond. Pump & Power Vent
15 = 15,000 Btuh L = Cond. Pump & Power Door
VOLTAGE
HEATER SIZES
3=230/208v 60 Hz 1 PH 00 = 0.0 KW
4=265v 60 Hz 1 PH 15 = 1.5 KW
5=240/220v 50 Hz 1 PH 25 = 2.5 KW
35 = 3.5 KW
3.7 KW (265V) Models
50 = 5.0 KW

C - 5
SPECIFICATIONS
NOTES:
1. All 265v models must use Amana’s subbase (PTSB4**C) or Amana’s hard wire kit (PTPWHWK4)
2. Minimum branch circuit ampacity ratings conform to the National Electric Code. However, local codes should apply.
3. Minimum voltage on 230/208 volt models is 197 volts; maximum is 253 volts. Minimum voltage on 265 volt models is 238.5 volts; maximum is 291.5 volts.
4. Overcurrent protection for all units without electric heaters is 15 amps. Overcurrent protection on 265 volt models must be cartridge-style time delay fuses
(included and factory installed on Amana all 265 volt chassis).
5. Heating capacity and efficiency is based on unit operation without condensate pump. Unit automatically switches to electric heat at approximately 24°F
outdoor ambient.
6. Total watts for 12,000 and 15,000 Btuh models. Subtract 70 watts for PT07/09*A**AC.
7. Please specify 2-digit heater kW size to complete model number.
8. Total amps for 12,000 and 15,000 Btuh models; subtract 0.2 amps for PT07/09*A*AC.
9. Refrigerant used in all systems is R-22.
(SeefacingpageforAuxillaryElectricHeaterPerformanceandPowerCordConfiguration)
* Approximately 95 CFM with optional power vent kit. Actual vent CFM performance will vary due to application and installation conditions.
**EER -Energy Efficiency Ratio per Air-Conditioning & Refrigeration Institute (ARI) Test Procedures and Canadian Standards Association (CSA) EEV Test Procedures
PTHModels-HeatPumps
COOLING/HEATPUMP&ELECTRICHEAT
AMANA C-MODEL
AMANA C-MODEL
COP - Coefficiency of Performance per ARI Test Procedures Units are rated for capacities and efficiencies.
Heat Pump Cooling Performance
Model (Basic) (NOTES 1, 7 & 9)
PTH073A**AC
PTH074A**AC
PTH093A**AC
PTH094A**AC
PTH123A**AC
PTH124A**AC
PTH153A**AC
PTH154A**AC
Voltage (NOTES 1 & 3) 230/208 265 230/208 265 230/208 265 230/208 265
Capacity (BTUH) 7,100 / 7000 7,100 9,000/8,800 9,000 12,000 / 11,800 12,000 14,000/13,800 14,000
Amps 2.8/3.0 2.3 3.5/3.8 3.0 4.6/5.0 4.3 6.3/6.9 5.9
Watts 615/610 615 805 / 785 805 1,120 / 1,110 1,120 1505 / 1485 1,505
EER** 11.5 11.5 11.2 11.2 10.7 10.7 9.3 9.3
Units without Electric Heater
Min.Circuit Ampacity (NOTES 2 & 4) 4.0 3.6 5.1 4.4 6.4 5.7 8.4 7.4
245 / 240 245 245 / 240 245 325 / 315 325 325/315 325
Low 220 / 205 220 220 / 205 220 250 / 229 250 250/220 250
265 / 260 265 265 / 260 265 345 / 335 345 345/335 345
Low 230 / 215 230 230 / 215 230 265 / 235 265 265/235 265
Ventilated Air, CFM (Fan Only)* 65* 65* 65* 65* 70* 70* 70* 70*
Ventilated Air, CFM (Compressor & Fan)* 65* 65* 65* 65* 70* 70* 70* 70*
Dehumidification (Pints/Hr.) 1.6 1.6 2.6 2.6 3.5 3.5 4.4 4.4
Net Weight (approximate lbs.) 95 95 100 100 110 110 115 115
Shipping Weight (approximate lbs.) 110 110 115 115 125 125 130 130
CFM (Cool, Wet Coil) High
CFM (Dry Coil) High
Heating Performance - Reverse Cycle
PTH073A**AC PTH074A**AC PTH093A**AC PTH094A**AC PTH123A**AC PTH124A**AC PTH153A**AC PTH154A**AC
BTUH (NOTE 5) 6,400/6,200 6,400 8,100/8,000 8,100 10,800/10,600 10,800 13,300/13,200 13,300
Amps 2.6/3.0 2.2 3.2/3.6 2.6 4.5/5.1 3.9 5.7/6.3 5.4
Watts 570/550 570 740/730 740 1,020/1,000 1,020 1,390/1,380 1,390
COP (NOTE 5) 3.3 3.3 3.2 3.2 3.1 3.1 2.8 2.8
CFM (Dry) 235/230 235 235/230 230 310/290 310 345/335 345
Heating, BTUH ° F
(Note 5) 62 7,400/7,200 7,400 9,700/9,600 9,700 13,000/12,800 13,000 15,800/15,700 15,800
57 7,100/6,900 7,100 9,200/9,100 9,200 12,300/12,100 12,300 15,000/14,900 15,000
Outdoor Ambient 52 6,700/6,500 6,700 8,600/8,500 8,600 11,600/11,400 11,600 14,200/14,100 14,200
47 6,400/6,200 6,400 8,100/8,000 8,100 10,800/10,600 10,800 13,300/13,200 5,440
Rating Point (COP)* 3.3/3.3 3.3 3.2/3.2 3.2 3.1/3.1 3.1 2.8/2.8 2.8
42 6,100/5,900 6,100 7,600/7,500 7,600 10,100/9,900 10,100 12,500/12,400 12,500
37 5,800/5,600 5,800 7,100/7,000 7,100 9,400/9,200 9,400 11,700/11,600 11,700
32 5,500/5,300 5,500 6,600/6,500 6,600 8,600/8,400 8,600 10,800/10,700 10,800
27 5,200/5,000 5,200 6,100/6,000 6,100 7,900/7,700 7,900 10,000/9,900 10,000
24
5,000/4,800
5,000
5,800/5,700
5,800
7,500/7,300
7,500
9,500/9,400
9,500
Watts 62 600/585 600 800/790 800 1,120/1,100 1,120 1,490/1,480 1,490
57 595/580 595 790/780 790 1,090/1,075 1,090 1,465/1,455 1,465
52 575/560 575 765/755 765 1,060/1,045 1,060 1,430/1,420 1,430
Outdoor Ambient 47 570/555 570 740/730 740 1,020/1,005 1,020 1,390/1,380 1,390
42 560/535 560 720/710 720 985/970 985 1,350/1,340 1,350
37 545/530 545 695/685 695 950/935 950 1,310/1,300 1,310
32 535/520 535 680/670 680 900/885 900 1,265/1,255 1,265
27 525/510 525 650/640 650 855/840 855 1,215/1,205 1,215
24
520/505
520
630/620
630
830/815
830
1,205/1,195
1,205
Heating Capacity
Reverse Cycle (NOTE 1)

C - 6
42"
(1066.8mm)
13-3/4"
(349.3mm)
16-1/16"
(408 mm)
ACCESSORIES
Wall Sleeve (42” wide x 16-1/16 high x 13-3/4” deep)
Standard insulated wall sleeve fits all Amana Pack-
aged Terminal Units. Shipped separately to allow in-
stallation during construction.
Outdoor Grilles
Available in stamped aluminum and an attractive ex-
truded aluminum architectural grille for application with
WS900B wall sleeve. The architectural grille is avail-
able in anodized natural, 3 stock colors and custom
colors to blend with the building exterior. CB=Clear,
DB=Dark Bronze, ZB=Driftwood, WB=White,
SB=Special (Custom) Color
Hard Wire Kit (not shown)
Used to permanently wire to chassis when standard
subbase and power cord are not utilized.
Power Disconnect Switch (not shown)
The PSHW**A power disconnect switch can be used
for 265 or 230/208 volt physical disconnect where re-
quired by local codes. The switch is rated at 30 amp
capacity. The switch is for use with Amana's standard
subbases or PTPWHWK4 Hard Wire Kit.
Subbase Kit
The fully skirted subbase conceals wiring while pro-
viding strong support, if needed. Plug-in receptacle
and field wiring access speeds installation. Electrical
accessories such as fuse holders, circuit breakers and
disconnect switches meet N.E.C. requirements.
Fuse Holder Kit (not shown)
Cartridge style fuses can be installed in fuse holder for
use in subbase or chassis. Available in 15, 20 and 30
amp. (Included on 265v unit).
Circuit Breaker Kit (230/208v only)
The circuit breaker kit, available in 15, 20 or 30 amp,
can be used with Amana's subbases. It gives over-
current protection and its location allows turning unit
on or off without tools.
External Transformer Kit (not shown)
40VA transformer to provide additional low voltage
power to accomodate a wide range of energy man-
agement systems or external relays. EXTRK01A and
EXTRK02A are the only approved transformer kits
that can be used.
Remote Temperature Sensor
Allows inexpensive, low voltage temperature sensing
on internal wall for more accurate temperature control.
Thermostats
The following thermostats offer remote control. Any
thermostat other than those listed must be submitted to
Amana for approval prior to use.
Wire Harness Kit (not shown)
Forquickconnectionsofremotethermostatorfrontdesk
with jumpers and connectors.
STC 30 Rating Accessory Kit (not shown)
Raises sound ratings from 27 to 30 to meet or exceed
most sound test requirements.
FHK315C 230/208V 15A
FHK320C 230/208V 20A
FHK330C 230/208V 30A
PSHW03A 230/208V
PSHW04A 265V
WS900B Wall Sleeve
PTPWHWK4 Hard Wire Kit
Skirting Skirting
Leveling Legs
Optional
Fuse Holder
Location
Optional
Power Switch and Circuit Breaker
Location
Power Receptacle
Subbase Box Assembly
CBK3**C Circuit Breaker Kit
Standard Outdoor Grille
SGK01B Single Pack
SGK10B Ten Pack
Architectural Grille
AGK01*B Single Pack
PTSB320C 230/208V 15/20A
PTSB330C 230/208V 30A
PTSB420C 265V 15/20A
PTSB430C 265V 25A
SGK
AGK
STC101A STC 30 Rating
Accessory Kit
RTS02
Remote
Temperature Sensor
Note:Thermostatslistedaremanualchangeover
withtheexceptionof20189101
NOTE: DO NOT CONNECT THE X1 TERMINAL.
EXTRK01A 208/230V
EXTRK02A 265V
AMANA C-MODEL
AMANA C-MODEL
Model Heat Stages Cool Stages Programmable Shape
C5200609 11No Round
D9945801 21No Rectangle
20189101 21No (Auto Changeover) Rectangle
1213410 21Yes Rectangle
PWHK01B Wire Harness Kit

C - 7
ACCESSORIES
CDP302 230/208V
CDP402 265V
Condensate Drain Kit
Attaches to the wall sleeve base pan for controlled inter-
nal or external disposal of condensate
Security Key Locks
In conjunction with the tamper-resistant front, the installa-
tionofAmana’ssecuritykeylockspreventstamperingofthe
controls used to set temperature, heating and cooling
functions. U.L. approved for institutional use only.
Remote Escutcheon Kit (not shown)
Optional kit for use with units controlled via a wall thermo-
stat. Replaces knob controls for units operated by wall
thermostat.
Condenser Baffle Kit
For use on non-baffled grilles. These deflectors direct the
air in toward the center and away from the inlet to prevent
recirculation of the hot condenser air.
Duct Extension Kit
Extends air distribution to an adjoining room. Consists of a
main duct for the room of origin and an extension duct to
reach the adjoining room and terminal duct.
Power Vent Kit (not shown)
Installation of Power Vent increases CFM up to approxi-
mately 95. Vent door will automatically close when unit fan
is off.
Power Door Kit (not shown)
Vent door will automatically open when unit fan is on.
Hydronic Transformer Relay Kit (not shown)
Add-on kit that allows field conversion of a standard PTC
unit to a Hydronic unit.
Hydronic Heat Kit
Add-on kits fit all units allowing the addition of hydronic
water or hydronic steam heat to cooling and heating units.
The kits feature left- or right-hand piping. Unit retains com-
plete service access with a kit installed.
Hydronic Valves (not shown)
Water and steam valves are available for use with the
HWK03 (water) and HVK03 (steam) heat kits. (See Ar-
chitects and Engineers Manual for specifications.)
Leveling Legs
Optional leveling legs fit wall sleeve to provide front sup-
port and leveling, if required. Four screws provided.
Condensate Removal Pump (not shown)
Can be field installed. Assists in removing condensate
developed by heat pump operation and transfers it to in-
door coil to dissipate into room while adding humidity to the
room.
Spare Filters (not shown)
Helps keep dirt and lint out of the air and off the coil, thus
increasing unit’s efficiency. Amana filters are easy to
remove, wash, and replace.
Heater Kit (for heaterless units only) (not shown)
Optional 1.5kW heater kits are available for use only with
models originally shipped without electric heat. Ask sales-
person for details.
MDK02 Main Duct
EDK02 Extension Duct
TDK02 Terminal Duct
Hydronic Air
Inlet FRONT VIEW
8-1/4"
20-3/16"
2-1/8"
53"
Steam/Water
Coil Position
Hot Water Inlet / Outlet Connections
Steam Inlet / Outlet Connection
Hot Water Inlet / Outlet Connections
Steam Inlet / Outlet Connections
16-3/4"
(unit wi/Hronic Kit installed)
FK10A Filters (10/pack)
KL03 Security Key Lock
DGK1 Condenser
Baffle Kit
REK10A Remote Escutcheon
Kit (10/pack)
HWK03 Hydronic Water Kit
HVK03 Hydronic Steam Kit
HTK3 230/208V
HTK4 265V
PVK3A 230/208V
PVK4A 265V
PDK3A 230/208V
PDK4A 265V
LL2B Leveling Legs
Condenser
Condenser Baffles
DK9001
Condensate
Drain Kit
Gasket
Cover
Plate
1/2" OD
Drain Fitting
(12.7mm)
AMANA C-MODEL
AMANA C-MODEL
*Poptop Actuator
BRACKET TRANSITION
DUCT
MAIN DUCT
MINIMUM
5"
BOTH SIDES
42-27/32" 6" TO 42-1/2"
BRACKET
5"
PARTITION
WALL
DUCT EXTENSION
AIR FLOW
DUCT
TERMINATION
KIT
AIR FLOW
1" to
adjoining
wall
surface
EDK02
MDK02
(Included in
MDK02)
Model
Nominal
BTUs 230V 208V 265V
Rated Watts All 1,500 1,200 1,500
7K & 9K 6.9 6.2 6.1
12K & 15K 7.1 6.4 6.3
7K & 9K 8.6 8.6 7.5
12K & 15K 8.8 8.8 7.7
Fuse Size All 15 15 15
Minimum
Ampacity
Full Load Amps
(including fan)
HK315F 230/208V
HK415F 265V
VS2WNCA* 2 way-24V-Steam-End Switch
VS2WNOA* 2 Way-24V-NO-Steam-End Switch
VW2WNCA* 2 Way-24V-NC-End Switch
VW3WNC2B* 3 Way-24V-NC/NO-End Switch

C - 8
U
RL
C
Ratings
Each unit must meet the following specifications:
ARI rating of _________BTUH cooling (and _________
BTUHreversecycleheatingwithaCOPof_________at47°
FO.D.)
Electric resistance heat of _________ BTUH. Total Amp
draw must be of _________ and _________ Watts at
_________ volts.
The unit must remove a minimum of _________ pints of
moisture per hour when operated at rating conditions. The
EER must be a minimum of _________ EER.
UnitChassis
Each unit must be slide out design shipped with room
cabinet front installed. Unit chassis must have the ability to
be installed with zero clearance from finished floor. An
electrical power cord must be included with chassis and
installed by the manufacturer to assure proper NEMA 6 or
7 configuration and UL approved length. Unit must be
tested for conformance to ASTME water infiltration specifi-
cation ASTME 331-86 which ensures no water infiltration
when tested at 8 inches rain per hour at 63 mph wind for 15
minutes.
Room Cabinet
The monochromatic front of the room cabinet must be able
to be field secured to chassis to inhibit tampering. Filter
must be accessible without removing room front. Cabinet
depthmust not exceed 7” to minimize unit’s impact onroom
space.
Coils
Unit’s coils must have rifled copper tubing expanded into
rippled-edge louvered aluminum fins.
Heat Pumps
Eachunitmustincludeachangeoverthermisterthatsenses
an outside ambient switch-over temperature as low as 24°
Fahrenheit, lock-open refrigerant reversing valve during
heat pump operation, temperature-activated defrost drain
and automatic emergency heat operation to override the
heat pump’s change-over thermostat and bring on electric
resistance heaters in the event of a sealed system failure.
Unit must not operate compressor and electric heaters
simultaneously.
Furnishandinstallaircooledthroughthewallpackageterminalairconditioners(heatpumps).Unitsareratedinaccordance
withtheARI(Air-Conditioning&RefrigerationInstitute)Standards310/380-93,andCSA(CanadianStandardsAssociation)
EEV certification programs and listed by U. L. (Underwriters Laboratories).
UnitControls
The unit’s controls must be completely wired and
accessible from the top. Controls must include high
and low fan speeds for both cooling, heating, and fan
only operation, and an OFF position. Other unit controls
must include a concealed ventilation control to allow the
introduction of filtered air into the room, a concealed fan
mode switch to allow the owner to preset for either
continuous fan or thermostatically cycled fan operation.
Additionally, the following controls are to be included as
standard on all units:
•Compressor restart delay
•Random restart circuit
•Front desk control capabilities
•Automatic room freeze protection
•Remote control capability
•Electronic temperature limiter
•Remote temperature sensing capability
•Load shedding capability
Evaporator/CondenserFans
Direct drive with a permanent split capacitor two-speed
motor. Condensate must be directed onto the con-
denser coil to aid in evaporation and removal. Con-
denser fan must be propeller type with slinger ring and
evaporator fan must be blower type.
Air Discharge
Must be a sloped surface so that obstructions cannot be
placed on the unit. Discharge conditioned air can be
directed into the room at an angle of 15 or 40 degrees
from the vertical position. The discharge grille must be
of polycarbonate material to resist bending, cracking,
rusting and corrosion.
Warranty
The warranty is for Full One Year on the entire unit; Full
Second through Fifth Year on the entire sealed refrig-
erant system components; Limited Second through
Fifth Year on functional parts only.
U
RL
Compressor
The compressor must be hermetically sealed, inter-
nallyisolated,rotary-type,andpermanentlymountedon
rubber isolators. No removal or adjustment of com-
pressor hold down bolts is to be required during instal-
lation.
AMANA C-MODEL
AMANA C-MODEL
GUIDE SPECIFICATIONS - Chassis

C - 9
Wall Sleeves
The wall sleeve must be industry accepted dimen-
sions: 13-3/4”depth x42”width x16-1/16”height and
constructed of insulated galvanized steel with electro-
deposition paint finish with ULV resistant high-solids
polyester overspray. Sleeve must be shipped with
weather resistant rear closure panel installed.
OutdoorGrilles
Must be architectural extruded, louvered aluminum
( AGK*** B) or standard stamped aluminum
(SGK**B). All other grilles must be submitted to PTAC
manufacturer for feasibility, airflow characteristics and
compliance with U.L. regulations, where necessary.
Remote Temperature Sensor (RTS02)
Afieldinstalledthermisterwilloverridetheunitmounted
thermostat to allow more accurate, internal wall-sens-
ing of room ambient temperature. All other modes and
functions remain at the PTAC unit.
CondensateDrainKit(DK9001)
Attaches to the bottom of the wall sleeve for directional
controlled internal or external disposal of condensate,
defrost, or rain water.
SubbaseKit(PTSB***C)
Necessary for U.L. listing requirements for 265 volt
units(HardWireKitmaybesubstitutedforSubbasekit).
Optional for 230/208 volt units. Must be prewired to
facilitatefieldelectricalconnectionsandincludeaNEMA
6 or 7 configuration electrical receptacle. It must have
twolevelingscrewsforsleevesupportandaccurateunit
leveling during installation. Locations for field installa-
tion of physical disconnect switches, cartridge-style
fuse holders and circuit breakers must be provided.
Side-skirts must be provided with subbases.
Power Vent & Damper
Mustbeprovidedtomaximizeventilationairintaketoup
to approximately 95 CFM. Power vent must be off and
damper door closed when unit fan is de-energized.
Fuse Holder (included in 265V chassis)
Must be installed either in the unit or the subbase and
must match the electrical requirements of the chassis.
SecurityKey Locks (KL03)
Must be installed to prevent tampering of the unit con-
trols. Unit room cabinet must also be secured to the
chassis with field supplied screws. U.L. approved for
institutional use only.
DuctKits(MDK02,EDKO2,TDK02)
Three kits must be supplied to provide ducted condi-
tioned air into a second room: a main duct kit, an
extension duct kit, and a terminal duct kit.
Hydronic Heat Kit
Is required for heating functions instead of electric
resistance heaters. Unit must retain complete service
access with the kit installed. Proper water or steam
valves must be used.
Condensate Removal Pump (Heat Pumps only)
Must be installed to assist in removing the condensate
developed by the heat pump operation and transfer it to
the indoor coil to dissipate into the room adding humid-
ity to the room.
DisconnectSwitch
Power disconnect switch must be installed in subbase
foruseasaphysical disconnectwhererequiredbylocal
codes.
Circuit Breaker Kit
Must be installed in subbase to provide overcurrent
protection for proper 230/208 volt amperage. Can also
be used as a physical disconnect where local codes
permit for 230/208 voltage.
Hard Wire Kit
Must be used to permanently wire chassis for hard wire
purposes. (For 265 volt units, Hard Wire Kit may be
substituted with Subbase Kit.)
Thermostats
A manufacturerapproved manual,auto changeover,or
programmable thermostat must be installed to provide
full remote operation of the chassis. A Remote Es-
cutcheonKitmustbeusedtoindicateremoteoperation.
(The optional accessories listed below perform specific functions required in some installations.)
(New installations typically require a minimum of WS900B wall sleeve and an outdoor grille.)
AMANA C-MODEL
AMANA C-MODEL
GUIDE SPECIFICATIONS - Accessories

C - 10
3 "
AIR DISCHARGE GRILLE CONTROL
DOOR
1"
1"
AIR
FLOW AIR
FLOW AIR
FLOW
6-1/8" 9-9/16" 24-5/16"
40"
42"
UnitwithWallSleeveandSubbaseAccessories
11-5/16"
16-1/16"
RIGHT SIDE VIEW
OPTIONAL
SUBBASE
40°
FRONT VIEW
58" CORD SET 230V/208V UNIT
18" CORD SET 265V UNIT
1" AND 3/4" CONCENTRIC KNOCKOUTS
BACK & BOTTOM OF SUBBASE
(ELECTRICAL ONLY)
WALL SLEEVE
1/2" O.D.
COPPER
DRAIN
TUBE
HINGED
CONTROL
DOOR
AIR DISCHARGE GRILLE IS
REVERSIBLE TO PROVIDE EITHER
15° or 40° DISCHARGE ANGLE
3-1/4"
MIN
2"
MAX
2-5/8"
7"
20-3/4"
1-3/8"
ARCH. GRILLE
1-3/8"
7/8"
STAMPED GRILLE
42"
16-1/16"
TOP VIEW
3 " clearance to sidewalls
RIGHT
LEFT
13/16"
13/16"
13-3/4"
4"
2-3/4"
Location of external drain holes
on bottom flange of Wall Sleeve
15°
(if the optional
subbase is used,
the wall sleeve
must extend at
least 2 3/4" into
the room)
STANDARDUNITDIMENSIONS
UnitwithAccessoryWallSleeveandSubbaseAccessory
(Optional)
(Shown with optional subbase)
58”CORDSET230V/208VUNIT*
18”CORD SET265VUNIT *
AMANA C-MODEL
AMANA C-MODEL
230/208 volt power receptacle must be within 54” of bottom right corner for 230/
208v installations.
265 volt per N.E.C must be hard wired. 18” power cords are designed to fit into
Amana PTSB4**C subbases.
*NOTES:

C - 11
ACCESSORYWALL SLEEVE INSTALLATION
Framingfor
AccessoryWallSleeve
(WS900B)
When installed in opening, the Wall
Sleeve must be horizontally level (side-
to-side) and pitched 1/4 bubble to the
outside. (NOTE: To ensure unit’s
maximum efficiency, DO NOT
over- or under-pitch.)
FASTENINGWALLSLEEVE
FINISHED FLOOR
42 1/4"
16 1/4"
MIN
MAIN STUD
JACK STUDS
HEADER - 4" x 4" OR
DOUBLE 2"x 4" ON EDGE
SUB-FLOOR
CRIPPLE
JACK STUD
ADJUST FRAMING TO
SECURE THIS DIMENSION
AMANA C-MODEL
AMANA C-MODEL
2" MIN
WOOD SCREW
TOGGLE BOLT
EXPANSION
ANCHOR BOLT
SCREWS
PLASTIC
ANCHOR
MOUNTING HOLES
(drilled by Installer)
NO HOLES
PERMITTED IN
BOTTOM OF CASE
(EXCEPTION -- INTERNAL
DRAIN KIT)
H
INSTALLATION NOTES
(1). If Subbase (PTSB***C) is installed, allow minimum 3-1/4” height clearance and maximum 5” height
clearance between wall sleeve and floor; allow minimum 2-3/4” protrusion from a finished wall. See
Note 4 if using hydronic units.
(2). DrainKit(DK9001)shippedseparately.Canbemountedeitherrightside,leftside,orbottomofsleeve.
If mounted to bottom of sleeve, allow 2” height clearance from floor to bottom of sleeve.
(3). For U.L. approval -- 265v units must use Amana Subbase (PTSB***C) or Amana Hard Wire Kit
(PTPWHWK4).Over-currentprotectionon265Vunitsmustbebycartridgestyletimedelayfuseswhich
areincludedandfactoryinstalledonAmana265vchassis.
(4). IfHydronicKit(HWK03orHVK03)isinstalled,WallSleevemustextendexactly3inchesintotheroom
from finished interior wall. If using subbase (PTSB***C) only the minimum 3¼” height clearance
between wall sleeve and floor is permissible.
(5). If Duct Kit (MDK02) is installed, allow minimum 1-3/8” into the room from finished interior wall.
Wall Sleeve must extend a
minimum of ¼” beyond
outside wall to allow for
proper caulking.

C - 12
Part No. 11046401 Rev. 5  6/2001Amana Heating and Air Conditioning
Printed in U.S.A. Fayetteville, TN 37334, U.S.A.
Should you have a service problem that is not resolved locally,
Write: Consumer Affairs Department - PTAC
Amana Heating and Air Conditioning
1810 Wilson Parkway
Fayetteville, TN 37334, U.S.A.
OrDial: 1-877-254-4729 between 8:00 AM and 4:30 PM (C.S.T.) Monday thru Friday
1-931-433-6101 outside U.S.A.
Or Fax: [phone]
Amana’s continuing commitment to quality products may mean a change in specifications without notice.
Form No. PDPTCA0100 •2001 Amana Heating and Air Conditioning, Inc. •1810 Wilson Parkway •Fayetteville, Tennessee, U.S.A.
•Printed in U.S.A. •Registered to ISO 9001 by QMI, Certificate #007062
For detailed information on operating specifications, dimensions, installation data, and accessories, refer to the
Amana Architects and Engineers Manual. To obtain a manual, consult your Amana representative.
OWNER'SRESPONSIBILITIES:
•Provide proof of purchase (sales invoice).
•Provide normal care and maintenance.
•Make product reasonably accessible for service.
•Pay for service calls related to product installation or usage
instructions.
•Pay for replacement of fuses and circuit breakers.
•Under the Limited Warranty, the owner is responsible for
servicer's travel charges, labor, parts freight and cartage, if
required.
WARRANTY LIMITATIONS:
•Warranty is effective as of the original date of purchase.
•All warranty service must be performed by an authorized Amana
Servicer.
•Reimbursement for warranty service is limited to normal service
charges performed during the servicer’s normal business hours.
•Applies only to original installation within the continental United
States, Hawaii, Alaska, and Canada.
•The warranty is void if the product serial identification tag is
removed or defaced to a point where the unit cannot be identified.
•Field installed accessories are only covered by the first year
warranty.
WARRANTYPROVIDESFOR:
FULLFIRSTYEARWARRANTY:Amana will repair orreplace,freeof charge, f.o.b. Fayetteville, Tennessee,any part of the unit or
Amanaaccessory, which proves to be defective due to workmanship or materials.
FULLFIVEYEARSEALEDSYSTEMWARRANTY: Amanawillrepairorreplace,freeofcharge,f.o.b.Fayetteville,Tennessee,the
evaporatorcoil, condenser coil, compressor or connecting tubing, which proves to be defective due to workmanshipor materialsor
non-reparablerefrigerant leak(s).
LIMITEDSECONDTHRUFIFTHYEARFUNCTIONALPARTSWARRANTY: Duringthe2ndthru5thyear,Amanawillprovide,freeof
charge,F.O.B.Fayetteville,Tennessee, functional partson the PTCor PTH unitwhich prove tobe defective dueto workmanship or
materials. Componentscoveredinclude: unit fan motor,unitmounted thermostats and thermisters,circuitboards, factory installed
hydronictransformer and relay, factory installed heaters and relays, unit blowerwheel andfan propeller, reversing valve solenoid and
capacitor. ThisLIMITEDWARRANTYdoesnotinclude diagnostic time, labor, oranytransportationandreinstallation charges that may be
required.
AMANA IS NOT RESPONSIBLE FOR:
•Damage as a result of flood, lightning, fire, wind, and
accidents beyond Amana’s control.
•Damage as a result of product not installed according to
Amana’s instructions and specifications.
•Replacement of fuses and replacement or resetting of
circuit breakers.
•Damage or failure resulting from installation in an
environment containing highly corrosive chemical agents.
•Damage or failure resulting from installation in a coastal
environment due to corrosion except those specific models
(i.e. Seacoast models) which have been treated with
factory applied corrosion protection.
•Damage and/or no start conditions caused by improper or
inadequate electrical connections.
•Damage resulting from failure to perform routine
maintenance as specified in the Operator’s Manual.
In no event shall Amana Heating and Air Conditioning be
responsible for incidental or consequential damages.*
*This warranty gives you specific legal rights, and you may have
others which vary from state to state. For example, some states
do not allow the exclusion or limitation of incidental or
consequential damages, so this exclusion may not apply to you.
For warranty service, contact an Authorized Amana Servicer.
PACKAGED TERMINAL PRODUCTS
(PTC, PTH “A” SERIES)
FULLONE-YEARWARRANTY
FULLSECONDTHRUFIFTH-YEARWARRANTY
ONSEALEDSYSTEMCOMPONENTS
LIMITEDSECONDTHRUFIFTHYEARWARRANTY
ONFUNCTIONALPARTS
Heating ®
&Air Conditioning
Comfort. Quality. Trust.st.