Amroad AMROAD P3 User manual

AMROAD P3
DOOR STATION
~
Installation Manual

AMROAD P3
Contents
Contents............................................. i
Package Contents...............................1
Rear Side ........................................... 2
Reset Button .................................................2
Installing Procedures......................... 3
Wire and Cable Connection..........................3
Install Main Unit .......................................... 4
IO Application ................................... 5
Electric Bolt.................................................. 5
Electric Strike ............................................... 6
PIR Motion Sensor and Light ........................7
Contents
i

AMROAD P3
Package Contents
1. Front panel
2. Main unit
3. 2-pin terminal block + cord end terminal ×2
4. 5-pin terminal block + cord end terminal ×5
5. H type terminal connector for power cord
6. Screws for firmness in solid concrete M4-L35
×4
7. Pin-Torx security screws M4-L10 ×2
8. Long Phillips screws M4-L55×4
9. Relay
10. L-shaped screw driver for security screws
11. Wall plugs ×4 + self tapping screws ×4
12. Blank RFID card
Package Contents
1

AMROAD P3
Rear Side
Reset Button
1. The device will be switched to the static IP
mode and reboot itself when the user has
pressed the reset button for 3 seconds. IP is
"192.168.0.50".
2. When the button has been pressed for
more than 6 seconds, the device will be
switched to the DHCP mode and reboot
itself (the users need to restore the factory
setting).
Rear Side
2

AMROAD P3
Installing Procedures
Wire and Cable Connection
1. Connect Power cord with 2-Pin terminal
block + cord end terminal together, and
insert it into DC 12V INPUT PORT.
2. Insert Ethernet cable into Ethernet port
according to the diagram above.
3. Connect the black wire (ground wire) to
the Mountingl Box. Remember to tighten
the screws on both sides. In order to
prevent power surge and lighting strike
from damaging the device, the Mountingl
Box should be connected to the earth wire
of the building.
4. For more information regarding to DI/DO
applications, please read P.5-7(IO
Application) for reference.
Installing Procedures
W
ire and Cable Connection
3

AMROAD P3
Install Main Unit
1. Place the main unit into the Mounting Box
and tighten four Phillips screws(M4-L35) .
2. Firmly press the front panel against the
device until the panel touches the wall.
3. Use the tool lift the doorbell button and
tighten 2 security screws (M4-L10) with the
L-shaped key.
4. Close the key by pressing it until it snaps.
5. Do not rip the plastic cover in order to
protect the front panel.
Installing Procedures
4

AMROAD P3
IO Application
Electric Bolt
The Electric Bolt is closed when +12 V is
supplied.
The Electric Bolt is opened when +12V is
not supplied.
DI1：The magnetic reed equipment should
set Low (HighLow), DI1 is used to detect
whether the door is closed well.
When the electronic circuit connected
with the Electric Bolt completely, you
should choose “Positive” in the item
Device Relay Output on the WEB UI in
Entrance Setting – GPIO, and saved.
Please follow Technical Manual to set
WEB UI.
IO Application
Electric
Bolt
5

AMROAD P3
Electric Strike
The Electric Strike is opened when +12 V is
supplied.
The Electric Strike is closed when +12V is
not supplied.
DI1：The magnetic reed equipment should
set Low (HighLow), DI1 is used to detect
whether the magnetic reed is revert.
When the electronic circuit connected
with the Electric Strike completely, you
should choose “Negative” in the item
Device Relay Output on the WEB UI in
Entrance Setting – GPIO, and saved.
Please follow Technical Manual to set
WEB UI.
產品應用
陰極鎖
IO Application
Electric
Strike
6

AMROAD P3
PIR Motion Sensor and Light
AMROAD P3 can also connect PIR (Passive
Infrared) motion sensor and Light. PIR
motion sensor detect whether person (or
living things) moves within the sensor range.
Once PIR motion sensor detects person (or
living things) moves, it will trigger the Light
to be turn on for 30 seconds.
DO2 Service
Device Relay Output：The way to detect set
High. If DI2 is triggered, DO2 will light up for
30 seconds automatically.
Trigger By Digital Input 2：The way to detect
set High (LowHigh). DI2 is used to connect
to PIR (Movement Detector, Intruder
Detector).
Please follow Technical Manual to set
WEB UI.
產品應用
PIR Motion Sensor and Light
IO Application
PIR Motion Sensor and Light
7

AMROAD TECHNOLOGY INC.
17F.-1, No.16, Jian 8th Rd., Zhonghe Dist.,
New Taipei City 235, Taiwan (R.O.C.)
TEL
886-2-8226-5686
FAX
886-2-8226-5687
i[email protected]
WWW.AMROAD.COM.TW