Amroad XL COMMUNITY STATION User manual

AMROAD XL
COMMUNITY STATION
~
Installation Manual

AMROAD XL
Contents
Contents............................................. i
Package Contents...............................1
Rear Side ........................................... 2
Reset Button .................................................2
Wire and Cable Connection............... 3
Power cord and Ethernet ..............................3
GPIO & Relay Control ...................................3
Ground Wire................................................. 4
Install Main Unit .......................................... 5
Use Fixing Tool to Lock................................ 6
IO Application ................................... 7
Electric Bolt...................................................7
Electric Strike ............................................... 8
Electric Lock with Open Door Button ......... 9
Contents
i

AMROAD XL
Package Contents
1. Main Unit x1
2. 2-pin terminal block + cord end terminal
x 2 (GRAY x1, BLUE x1)
3. 5-pin Terminal block + 2-pin Terminal
block + Cord End Terminal x7 (YELLOW
x7)
4. Relay x1
5. Fixing Tool x1
Package Contents
1

AMROAD XL
Rear Side
After unfasten Rear Cover, IO connecter will
show above.
Reset Button
1. The device will be switched to the static IP
mode and reboot itself when the user has
pressed the reset button for 3 seconds. IP is
"192.168.0.50".
2. When the button has been pressed for
more than 6 seconds, the device will be
back to the factory setting and reboot
itself.
3. If press for more than 6 seconds, system
will clean Master RFID Card, Configuration,
and Number Entry Screen data. Network
default is DHCP mode.
Rear Side
Rear Cover
2

AMROAD XL
Wire and Cable Connection
Power cord and Ethernet
1. Connect Power cord (DC12V) with 2-Pin
Terminal block and Cord End Terminal.
2. Connect Ethernet. (RJ-45 Connector).
GPIO & Relay Control
For more information regarding to DI/DO
applications, please read P.7-10(IO Application)
for reference.
IO Connection：
1. DI1 (Digital Input port 1) ：DI1 is used for
detecting whether the door is closed or not.
2. DI2 (Digital Input port 2) ：DI2 is used to
connect to indoor “Open Door” button. (Or,
it is used for PIR.)
3. DO1 (Digital Output port 1) ：DO1 is used
for external lighting.
4. DO2 (Digital Output port 2) ：(Reserved)
5. CTRL 1：Connect to CTRL 1 on Relay Board
to control Electronic Door Lock.
6. (-) (GND) ：Connect to GND
Installing Procedures
Wire and Cable Connection
3

AMROAD XL
Ground Wire
1. Connect the black wire (ground wire) to
the wall box. Remember to tighten the
screws on both sides. In order to prevent
power surge and lighting strike from
damaging the device, the wallbox should
be connected to the earth wire of the
building.
2. Connect the screw (for earth wire) of wall
mounting box to ground wire of the
building and fasten them. Then, ground
wire of mounting box is connected with
device.
Installing Procedures
Wire and Cable Connection
4

AMROAD XL
Install Main Unit
1. Confirm mounting box, power cord,
Ethernet and IO controllers are connected
well.
2. Make sure “Slide Guide” and “Guide Rod”
on the right position. Otherwise, they
would not bump into “Iron Plate for Latch.”
3. Smoothly let upper Guide Rod and lower
Guide Rod slide into both Slide Guide and
firmly push Main Unit toward the wall.
4. Push down Main Unit and secure it on the
wall.
Installing Procedures
5

AMROAD XL
Use Fixing Tool to Lock
1. Insert “Fixing Tool” into device and
mounting box.
2. If move the “Fixing Tool” to the right side,
Slide Latch will be moved to lock on the
wall.
3. Remove the “Fixing Tool.”
Installing Procedures
6

AMROAD XL
IO Application
Electric Bolt
The Electric Bolt is closed when +12 V is
supplied.
The Electric Bolt is opened when +12V is
not supplied.
DI2：Trigger Default is High (LowHigh).
When the Open Button is pressed, the door
will be opened.
DI1：Trigger Default is HighLow,
MS(Magnetic Switch). Magnetic Switch is
detecting door status.
When the electronic circuit connected with the
Electric Bolt completely, you should choose
“Positive” in the item Device Relay Output on
the WEB UI in Entrance Setting – GPIO, and
saved.
Please follow Technical Manual to set WEB UI.
IO Application
Electric Bolt
7

AMROAD XL
Electric Strike
The Electric Strike is opened when +12 V
is supplied.
The Electric Strike is closed when +12V is
not supplied.
DI2：Trigger Default is High (LowHigh),
When the Open Button is pressed, the door
will be opened.
DI1：Trigger Default is HighLow。
When the electronic circuit connected with the
Electric Strike completely, you should choose
“Negative” in the item Device Relay Output on
the WEB UI in Entrance Setting – GPIO, and
saved.
Please follow Technical Manual to set WEB UI.
IO Application
Electric Strike
8

AMROAD XL
Electric Lock with Open Door Button
In addition to Electric Lock and Open Door
Button, we use wires, Relay Board, Core End
Terminal, 2-pin and 5-pin Terminal Block to
build circuit.
It’s necessary to connect with Ethernet cable
and external DC power. Also, you need to
configure WEB UI as previous section mentions.
If all above steps are correct, you can press
Open Door Button to trigger the Electric Lock
(open door).
IO Application
Electric Lock with Open Door Button
9

AMROAD XL
IO Application
Electric Lock with Open Door Button
10

AMROAD TECHNOLOGY INC.
17F.-1, No.16, Jian 8th Rd., Zhonghe Dist.,
New Taipei City 235, Taiwan (R.O.C.)
TEL
886-2-8226-5686
FAX
886-2-8226-5687
i[email protected]
WWW.AMROAD.COM.TW