APS iBoard IB-019&020A-B User manual

iBoard®
Customer Support: [email protected]
Rev. 20210301
1
iBoard® by APS
PART#: IB-019&020A-B
PART LIST
*BODY FRAME MOUNT
*NO DRILLING REQUIRED
Fastener Size Tightening Torque (ft-lbs)
6mm 6-7
8mm 16-18
10mm 31-32
12mm 56-58
14mm 92-94
Front
READ INSTRUCTIONS CAREFULLY BEFORE
START ING INSTALLATION. REMOVE CONTENTS
FROM BOX AND VERIFY ALL PARTS ARE PRE-
SENT. ASSISTANCE IS RECOMMENDED.
Driver Front Mounting
Bracket (DFM)
Passenger Front Mount-
ing Bracket (PFM)
Driver Rear Mounting
Bracket (DRM)
Passenger Rear Mount-
ing Bracket (PRM)
Driver Front Support
Bracket (DFS)
Passenger Front Support
Bracket (PFS)

iBoard®
Customer Support: [email protected]
Rev. 20210301
2
X8
M6X1-20mm
Square Head Bolt
M6 Large Flat
Washer
X8
STEP 1
M6X1 Nylon
Lock Nut
X8
STEP 3
Select Driver Front Support Bracket (DFS) and insert (1)
M12X1.75-120mm Hex Bolt with (1) M12 Large Flat Washer
through the mounting slot. Place (2) M14 Large Flat Washers
onto the M12 Hex Bolt between the Support Bracket and the
factory body mount, (Fig 2A & 2B).
Insert the M12 Hex Bolt up through the holes in the factory body
mount and secure with (1) M12 Large Flat Washer, (1) M12
Lock Washer and (1) M12 Hex Nut, (Fig 3). Do not fully tighten
hardware at this time.
Start installation from the driver side front of the vehicle. Re-
move the factory front body mount bolt from the underside of
the cab.
NOTE: Factory body mount bolts will need to be driven out of
and back into the steel washer molded into the rubber bushing.
Take precautions to avoid damage to the threads or the washer
and bushing, (Fig 1).
X4
M14 Large Flat
Washer
M12 Hex Nut
X4
M12 Lock Washer
X4
M12X1.75-120mm Hex Bolt
X2
M12X1.75-30mm Hex Bolt
X2 X8
M12 Large Flat
Washer
Fig 1
STEP 2
Locate the Driver Front Mounting Bracket (DFM) and bolt it to
the vehicle using the factory body mount bolt. NOTE: Brackets
mount over bushings. Do not fully tighten at this time. (Fig 2B) Driver Side Front Support Bracket Installation
(2) M14 Large Flat Washers
(1) M12 Large Flat Washer
(1) M12X1.75-120mm Hex Bolt
Fig 2A

iBoard®
Customer Support: [email protected]
Rev. 20210301
3
STEP 4
Line up the mounting hole in the Driver Front Support Bracket
with the hole in the Driver Front Mounting Bracket, (Fig 4). At-
tach the Support Bracket to the Mounting Bracket use the in-
cluded (1) M12X1.75-30mm Hex Bolt, (2) M12 Large Flat
Washers, (1) M12 Lock Washers and (1) M12 Hex Nut, (Fig 4).
Do not fully tighten hardware at this time.
(Fig 4) Driver Side Front Mounting Bracket Assembly
Front
STEP 6
Select a Running Board. Slip (2) M6X1-20mm Square Head
Bolts into each bottom channel (Fig 5). Carefully position the
Running Board onto the (2) Mounting Brackets.
IMPORTANT: Do not slide the Running Board on the Brackets
or the bottom surface of the board will be damaged. Attach the
Running Board to each Mounting Bracket with (2) M6x1-20mm
Square Head Bolts, (2) M6 Large Flat Washers and (2) M6 X1
Nylon Lock Nuts (Fig 6). Do not fully tighten at this time.
(Fig 5) Slip M6X1-20mm Square Head Bolts Into The Bottom
Channels
(Fig 3) Driver Side Front Support Bracket Installation
(1) M12 Large Flat Washer
(1) M12 Lock Washer
(1) M12 Hex Nut
STEP 5
Move to the rear mounting location. Locate the driver side rear
Mounting Bracket, repeat Steps 1 for Driver Rear Mounting
Bracket (DRM) installation. Do not fully tighten hardware at this
time.
DFM
DFS
(1) M12X1.75-30mm Hex Bolt
(2) M12 Large Flat Washers
(1) M12 Lock Washer
(1) M12 Hex Nut
Front
(Fig 6) Running Board Installed Onto the Mounting Bracket
(2) M6X1-20mm Square Head Bolts
(2) M6 Large Flat Washers
(2) M6 Nylon Lock Nuts

iBoard®
Customer Support: [email protected]
Rev. 20210301
4
STEP 7
Level and adjust the Running Board and fully tighten all hard-
ware.
(Fig 7) Installation Completed
STEP 8
Repeat Steps 1-7 for other side Running Board installation.
The installation is completed (Fig 7).
Attention
Do periodic inspections to the installation to make sure
that all hardware is secure and tight.
In order to protect your bars/boards, please use only
mild soap/non-abrasive products for cleaning.