APS iArmor IA-S159 User manual

iArmor®
Customer Support: [email protected]
Rev. 20201201
1

iArmor®by APS
PART#:IA‐S159
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE
PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION. ASSISTANCE IS RECOMMEND-
ED. THANK YOU FOR CHOOSING OUR PRODUCT!
Fastener Size Tightening Torque (ft-lbs)
6mm 6-7
8mm 16-18
10mm 31-32
12mm 56-58
14mm 92-94
PART LIST
Driver Side Step Bar Passenger Side Step Bar
Front
Driver Center Mounting
Bracket (DFM/DCM/PRM)
Driver Rear Mounting
Bracket (PFM/PCM/DRM)
Passenger Center
Mounting Bracket
(PFM/PCM/DRM)
Passenger Rear
Mounting Bracket
(DFM/DCM/PRM)
X1
X1
X1
X1
PART LIST
Driver Side Step Bar Passenger Side Step Bar
Front
Driver Front Mounting
Bracket (DFM/DCM/PRM)
Passenger Front
Mounting Bracket
(PFM/PCM/DRM)
X1 X1
*Driver Front Mounting Bracket , Driver Center Mounting and
Passenger Rear Mounting Bracket are Universal.
*Passenger Front Mounting Bracket , Passenger Center
Mounting Bracket and Driver Rear Bracket are Universal.

iArmor®
Customer Support: [email protected]
Rev. 20201201
2
The instruction here is for your reference only. We strongly
recommend the professional installer for best result. We are not
responsible for any damage caused by the installation.
STEP 1
Start the installation under the driver side of the vehicle. Locate
the front (2) factory studs along the inner side of the body pan-
el, (Fig 1). NOTE: Chase threads on the studs first before in-
stalling Brackets to remove paint buildup.
M8X1.25 Hex Nut
X6
M8X1.25-55mm Carriage Bolt
X6
M8 Large Flat Washer
X18
M8 Lock Washer
X6
U Bracket
X6 X12
Spacer
(Fig 2) Driver Front Mounting Bracket Installation
(Fig 1) Driver Front Mounting Bracket Location Pictured
(2) M8 Large Flat Washers
(2) M8X1.25 Nylon Lock Nuts
Front
Select (1) Driver Front Mounting Bracket. NOTE: Driver Front
Mounting Bracket, Driver Center Mounting Bracket and
Passenger Rear Mounting Bracket are universal. Attach the
Mounting Bracket to the (2) factory studs with (2) M8 Large Flat
Washers and (2) M8X1.25 Nylon Lock Nuts (Fig 2). Leave
bracket loose at this time.
STEP 2
X12
M8X1.25 Nylon Lock Nut
Front
Move to Driver Side Center & Rear Mounting Locations (Figs 3
& 4). Repeat Steps 1-2 to install the Mounting Brackets. Leave
brackets loose at this time.
STEP 3

iArmor®
Customer Support: [email protected]
Rev. 20201201
3

STEP 4
Once all (3) driver side mounting brackets are installed, select and attach the Driver Side Step Bar onto the Mounting Brackets with
(3) U Brackets, (6) Spacers, (3) M8X1.25-55mm Carriage Bolts, (3) M8 Large Flat Washers, (3) M8 Lock Washers and (3) M8X1.25
Hex Nuts (Fig 5). Do not fully tighten hardware at this time.
(Fig 5) Driver Side Step Bar Installed
Front DFM
DCM
DRM
NOTE: Torque all M8 X1.25-55mm Car-
riage Bolts to 16~18 Ib-ft. Don't over
tighten, or the aluminum square bars
will be damaged by the brackets
M8X1.25-55mm
Carriage Bolt
U Bracket
Spacers
M8 Large Flat Washer
M8 Lock washer
M8X1.25 Hex Nut
(Fig 4) Driver Rear Mounting Bracket Location Pictured
(Fig 3) Driver Center Mounting Bracket Location Pictured
Rear
Front

iArmor®
Customer Support: [email protected]
Rev. 20201201
4
(Fig 6) Installation Completed
Attention
Do periodic inspections to the installation to make sure
that all hardware is secure and tight.
In order to protect your bars/boards, please use only
mild soap/non-abrasive products for cleaning.
STEP 5
Properly level and adjust the Step Bar and fully tighten all hard-
ware.
STEP 6
Move to the passenger side of the vehicle. Repeat Steps 1-5 to
install passenger side step bar.
Installation completed (Fig 6).