APS iBoard IB-R962 User manual

Customer Support: [email protected]
Rev. 20211001
1
iBoard
®
iBoard® by APS PART#: IB-R962
READ INSTRUCTIONS CAREFULLY BEFORE START ING
INSTALLATION. REMOVE CONTENTS FROM BOX AND
VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS
RECOMMENDED.
*ROCKER PANEL MOUNT
*DRILLING IS REQUIRED
Item QTY Description Item QTY Description
1# 2Driver / Passenger Front Mounting Brackets 7# 16 M8 Nylon Lock Nuts
2# 4Driver / Passenger Center Mounting Brackets 8# 16 ST6.3x22mm Hex Self Tapping Screws
3# 2Driver / Passenger Rear Mounting Brackets 9# 16 M6X1-20mm Square Head Bolts
4# 8Support Brackets 10# 16 M6 Large Flat Washers
5# 16 M8X1.25-20mm Hex Bolts 11# 16 M6 Nylon Lock Nuts
6# 32 M8 Flat Washers
7 # 11 #
10 #
9 #
Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 √
8mm 16-18 √
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X
6 #
5 # 8 #

Customer Support: [email protected]
Rev. 20211001
2
iBoard
®
PassengerDriver Front
4#
4#
2#
2#
3#
3#
4#
4#
4#
4#
4#
4#
2#
1# 1#
2#

Customer Support: [email protected]
Rev. 20211001
3
iBoard
®
STEP 1
Start installing from the driver side of the vehicle, drill 5/16’’
holes on pinch weld as shown (Both sides), (Fig 1).
(Fig 1) Driver Side Mounting Locations
STEP 2
Assembly Driver Front Mounting Bracket and Support Bracket
with (1) M8X1.25-20mm Hex Bolt, (2) M8 Flat Washers and (1)
M8 Nylon Lock Nut, (Fig 2). Do not fully tighten at this time.
Then attach the assembled Driver Front Mounting Bracket to
vehicle with (2) ST6.3x22mm Hex Self Tapping Screws, (1)
M8X1.25-20mm Hex Bolt, (2) M8 Flat Washers and (1) M8 Ny-
lon Lock Nut, (Fig 3). Do not fully tighten at this time.
(Fig 2) Driver Front Mounting Bracket Assembly
Front
Support Bracket
Driver Front Mounting
Bracket
(Fig 3) Driver Front Mounting Bracket Installation
Support Bracket
(2) ST6.3x22mm Hex
Self Tapping Screws
(1) M8X1.25-20mm Hex Bolt
(2) M8 Flat Washers
(1) M8 Nylon Lock Nut
Driver Front
Mounting Bracket
STEP 3
Move to driver side other (3) Mounting locations. Repeat Steps
1-2 for Mounting Bracket and Support Bracket assembly and
installation. Don’t fully tighten hardware at this time.
STEP 4
Select a Running Board. Slip (4) M6x1-20mm Square Head
Bolts into each bottom channel (Fig 4). Carefully position the
Running Board onto the (4) Mounting Brackets.
IMPORTANT: Do not slide the Running Board on the Brackets
or the bottom surface of the board will be damaged. Attach the
Running Board to each Mounting Bracket with (2) M6x1-20mm
Square Head Bolts, (2) M6 Large Flat Washers and (2) M6
Nylon Lock Nuts (Fig 5). Do not fully tighten at this time.
(1) M8X1.25-20mm Hex Bolt
(2) M8 Flat Washers
(1) M8 Nylon Lock Nut

Customer Support: [email protected]
Rev. 20211001
4
iBoard
®
STEP 5
Level and adjust the Running Board and fully tighten all hard-
ware.
Important: Please follow the recommended Tightening Tor-
ques shown in the table on page 1. Don’t over tighten, or
the nuts/bolts will be damaged.
STEP 6
Repeat Steps 1-5 for the other side Running Board installation.
The installation is completed.
Attention
Do periodic inspections to the installation to make sure
that all hardware is secure and tight.
In order to protect your bars/boards, please use only
mild soap/non-abrasive products for cleaning.
(Fig 4) Slip M6X1-20mm Square Head Bolts Into
The Bottom Channels
M6X1-20mm Square Head Bolts
(Fig 5) Running Board Installed Onto Mounting Bracket
(2) M6X1-20mm Square Head Bolts
(2) M6 Large Flat Washers
(2) M6 Nylon Lock Nuts