arf LITTLE TONI EP User manual

It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
Warning ! This model is not a toy.
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
* Specifications are subject to change without notice.*
www thewingsmaker com. .
Wing Span:40 in / 1020 mm
Wing Area: 310 sq in / 20 sq dm
Flying Weight: 28 6 oz / 810 g
Fuselage Length: 36 in / 910 mm
Requires: 4- channel radio w/ 4 micro servos,
20A Brushless ESC and 3 cells 11 1V
2100 mAh Li Po battery charger. -
.
.
&
SpecificationsSpecifications
GE030
Before commencing assembly please read these instructions thoroughly , .
I NSTRUCT I ON M ANUAL
LITTLE TONI EP

BEFORE YOU BEGIN
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P.1
P.2
P.3-P.9
P.9
Apply epoxy glue. Apply instant glue
(C.A.glue, super glue.)
Ensure smooth non-binding
movement while assembling.
Cut off shaded portion.
Must be purchased separately!Apply thread locker
Do not overlook this symbol!
Assemble left and right
sides the same way.
Pierce the shaded portion
covering film.
Peel off shaded portion
covering film.
Drill holes with the specified
diameter (here: 3mm)
Pay close attention here!
Read through the manual before you begin, so you will have an overall idea of what to do.
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for
warranty replacement. The manufacturer will replace any defective parts, but will not extend
to the parts that are good before gluing to defective parts during assembly. Warranty will
not cover any parts modified by customer.
Symbols used throughout this instruction manual comprise of the following :-
1
2
3
3mm
P.1
LITTLE TONI EP

6. SCREW PB2x10mm -- 2 pcs
CLEVIS -- 1 pc.
FUEL TUBE d2xD4x4mm -- 1 pc.
HORN -- 1 set
PUSHROD Ø1.4x427mm w/ Threads (For Rudder) -- 1 pc.
7. CLEVIS -- 1 pc.
FUEL TUBE d2xD4x4mm -- 1 pc.
PUSHROD Ø1.4x418mm w/ Threads (For Elevator) -- 1 pc.
8. SCREW PM3x6mm -- 4 pcs
WASHER d3xD7mm -- 4 pcs
FOLDING PROPELLER SET (PL6314020) -- 1 set
COWLING -- 1 pc.
SCREW PWA2x8mm -- 4 pcs
SPINNER Ø45mm -- 1 set
9. BATTERY TIE 200mm -- 1 pc.
FUEL TUBE d2xD4x4mm -- 2 pcs
STRAPER -- 2 pcs
SPONGE 10x50x150mm -- 1 pc.
DOUBLE-SIDED TAPE 30x35mm -- 1 pc.
10. SCREW PM2.5x20mm -- 2 pcs
WASHER d2.6xD8mm -- 2 pcs
PVC PLATE 1x20x68mm -- 1 pc.(For Wing Protection)
11. CANOPY -- 1 pc.
SCREW PWA2x8mm -- 4 pcs
12. DECALS: GE030DEC -- 1 pc.
Parts List
P.2
COVERING:--
LIGHTEX SGX 100 WHITE
LIGHTEX SGX 312 BRIGHT RED
1. MAIN WING -- 1 pair
2. SERVO MOUNTING PANEL -- 1 pair
SCREW PB2x12mm -- 4 pcs
SCREW PA1.7x8mm -- 8 pcs
STRAPER -- 2 pcs
CLEVIS -- 2 pcs
HORN -- 2 sets
FUEL TUBE d2xD4x4mm -- 4 pcs
PUSHROD Ø1.4x93mm w/ Threads (For Aileron) -- 2 pcs
3. MAIN LANDING GEAR -- 1 pair
SCREW PWA2x10mm -- 6 pcs
MAIN WHEEL Ø40mm -- 2 pcs
WHEEL PANTS -- 1 pair
COLLAR Ø3.1mm w/ set screw -- 2 sets
SCREW PM3x25mm -- 2 pcs
SCREW PWA2x6mm -- 4 pcs
M3 NUT -- 2 pcs
WASHER d3xD7mm -- 4 pcs
COPPER TUBE d3.1xD4x4mm -- 2 pcs
PLATE 0.5mm -- 1 pair
4. STABILIZER & ELEVATOR -- 1 set
FUSELAGE -- 1 pc.
ELEVATOR LINK PL4510010 -- 1 pc.
SCREW PB2x8mm -- 2 pcs
5. VERTICAL FIN & RUDDER -- 1 set
TAIL LANDING GEAR -- 1 set
TAIL WHEEL Ø23mm -- 1 pc.
PLASTIC COLLAR d1xD5x2mm -- 2 pcs
SCREW PA2x8mm -- 2 pcs
SCREW PM2x8mm -- 1 pc.
M2 NUT -- 1 pc.
ALUMINUM PLATE 0.3mm -- 1 pc.

Main Wing
Bottom View
Bottom View
Aileron Servos
Apply instant type CA glue to both sides of each hinge.
Aileron Servo Lead
Please choose either 02L & 02R or 03L & 03R or 04L & 04R that suits your servo.
Clevis
Horn
Fuel Tube
d2xD4x4mm
PB2x12 mm Screw
PB2x12mm
PA1.7x8mm Screw
Ø1mm pilot holes for The Wings Maker horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
Straper Fuel Tube
d2xD4x4mm
PA1.7x8mm
Pushrod
Ø1.4x93mm
P.3
4
8
2
1
02L
03L
04L
02R
03R
04R

Completed
PWA2x6mm
1mm
PM3x25mm Screw
d3xD7mm Washer
4
3.1mm Wheel Collar
2
2
M3 Nut
2
PWA2x10mm Screw
6
PWA2x6mm Screw
4
PWA2x10mm
Stabilizer & Elevator
Main Landing Gear
Completed
Apply instant type CA glue to both sides
of each hinge.
PB2x8mm Screw
2
PB2x8mm
Wheel Pant
Ø1mm pilot holes for The Wings Maker
tri-horn are pre-drillde. Please look for
pin-hole marks at under side of control
surfaces.
P.4
4
3
A A'
A=A'
(Main Wi ng)
(Stabilizer)
B B'
B=B'
Temporary install the main
wing, adjust leveling of the
stabilizer to make it as
parallel to the main wing
as possible
Bottom View
PM3x25 mm
Plate 0.5mm
d3xD7mm
Washer
Wheel
Ø40mm
3mm
Set Screw
3.1mm
Collar
M3 Nut
Copper Tube
d3.1xD4x4mm

Ø1mm pilot holes for The Wings Maker horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
Rudder Pushrod
Vertical Fin, Rudder & Tail Landing Gear
Bottom View
Completed
Apply instant type CA glue
to both sides of each hinge.
PA2x8mm Screw
2
PB2x10mm Screw
2
C C'
C=C'
1mm
P.5
6
5
Plastic Collar
Wheel 23mm
PA2x8mm
M2 Nut
PM2x8mm
Ø
M2 Nut
1
PM2x8mm Screw
1
PB2x10mm
Clevis
Horn Fuel Tube
d2xD4x4mm
Pushrod
Ø1.4x427mm
75mm 24mm

PM2x12mm Screw
PM3x6mm
PM2x12mm
PM2x12mm
d3xD7mm Washer d3xD7mm Washer
M5 Nut
PWA2x8mm Screw
PWA2x8mm
4
2
PM3x6mm Screw
4
4
Don’t over-tighten the PM2 screws, let the
propeller blades align themselves when
spinning.
Don't over-tighten the
PM3 screws, too much
stress on the screws
could split the firewall.
Outrunner Motor 28/ 30
KM0283010
Propeller Adaptor (d3xD5)
HW2340100
Elevator Pushrod
Outrunner Motor/ Cowling
Bottom View
Completed
Make sure rotating
motor casing is not
in contact with
wirings or anything.
P.6
7
8
60mm
35mm
Spinner
Ø45mm
1.5mm
Optional Parts
Clevis
Fuel Tube
d2xD4x4mm
Pushrod
Ø1.4x418mm
Solder
Solder
TWM
KP0011310

PM2.5x20mm Screw
PM2.5x20mm
d2.6xD8mm Washer
d2.5xD8mm Washer
2
2
PVC Plate 1x20x68mm
Radio Equipment
Main Wing
Bottom View
Top View Completed
Bottom View
Front
Sponge Fuel Tube
d2xD4x4mm
Elevator Pushrod
Ø1.4x418mm
Rudder Pushrod
Ø1.4x427mm
Receiver
Straper
Elevator Servo
Battery Battery Tie
Rudder Servo
20A Brushless ESC
Double-Sided Tape
Install and arrange the servos as shown in the diagram.
P.7
9
10
2.5mm

4
Adjust the wing and fuselage configuration as shown in the diagrams.
A=A' B=B'
C=C' D=D'
A A'
BB'
D'
D
CC'
Canopy
Wing Setting
PWA2x8mm Screw
P.8
11
12
1.2mm
PWA2x8mm

# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.
# is specially designed to be powered by 180W Motor System.
# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running
propeller. Extreme caution should be exercised when working with electric powered models. Make sure the
propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure
you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental
movement of the throttle stick will spin the propeller and could cause injuries.
# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles.
Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone.
Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the
glue and shrink the covering at the same time, causing the seams to pull away.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
C.G.
The ideal C.G. position is 74mm (2.9 in.) behind the leading edge
measured at where the wing meets the fuselage. In order to obtain
the C.G. specified, add weight to the fuselage or move the battery
position. Check the C.G. before flying.
74mm
C.G.
2.9 in
P.9GE030PO18130809
14
Warning!
Important Safety Precautions
Control Throws
Adjust the control throws as shown in the
diagram. These throws are good for general
flying. You can adjust according to your
personal preference.
Elevator
Rudder
15mm
15mm
10mm
6mm
6mm
10mm
Aileron
13
LITTLE TONI EP

THE WINGS MAKER
www.thewingsmaker.com
GE030PO18130809