Argos OXFORD DINING FURNITURE Product information sheet

OXFORD DINING FURNITURE
Extendable Dining Table
Easy Assembly Instructions
Before you
start, here is
some helpful
advice
1. We suggest you spend a short time reading through this leaflet and then
follow the simple step by step instructions.
2. Do not discard any of the packaging until you have checked that you have
all the parts and the pack of fittings.
3. Assemble this product on a carpet.
4. All you will need to assemble this unit is a screwdriver and light hammer.
5. Keep glue and fittings out of childrens’ reach.
In the unlikely event that this product has missing or
damaged parts, please call 0845 640 0800 to obtain spares.
2100mm
900mm
750mm

Component parts and fittings contained in the box
Fittings
M16/8.5x1.2mm Washer x 8
A
D
C
E
B
F
M13/8.5x2.5mm Gasket x 8
W13.5xT2mm Spanner x 1
M8x13mm Nut x 8
M8x80mm Bolt x 8
12x60mm Nut x 4
1
2
22
2
3
3
Extendable Dining Table
43x35x34mm x4
G
Total: 7 Parts

ASSEMBLY - STAGE ONE
Leg Assembly
Insert ○ B into
○
2 .
Screw in bolts
○
A into
○
B .
Repeat for all
four legs.
A
A
2
x4 B
Set the legs onto
Screw in the
nuts
○
C with the
○
E and
○
D by
○
F .
Tighten the nuts.
the base of table.
1
D
C
E
F
1.
2.
3.
4.
5.
6.

ASSEMBLY - STAGE TWO
Leaf Assembly
Insert
are held
○
3 into
the holes of short
securely by the
wedge under the
table.
rail (x2). Make
sure the rails of
○
3
3
3
7.

ASSEMBLY - STAGE THREE
How to shorten the table
To shorten the
table,
○
remove the
leaves 3 from
the sides. Turn
them over, and
insert them under
the top 1 ,
one on each side.
○
○
Turn the wood
block between the
leaves under the
table to hold them
in place.
Fill in the holes
of short rail with
four wood blocks
G .
G
G
3
3
1
8.
9.

Oxford - Extendable Dining Table
Assembly Instructions - Please keep for future reference 603/0438
Dimensions
Length - 210cm
Width - 90cm
Height - 75cm
Ｉｍｐｏｒｔａｎｔ – Ｐｌｅａｓｅ ｒｅａｄ ｔｈｅｓｅ ｉｎｓｔｒｕｃｔｉｏｎｓ ｆｕｌｌｙ ｂｅｆｏｒｅ ｓｔａｒｔｉｎｇ ａｓｓｅｍｂｌｙ
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 640 0800
Issue 1 - 9/12/09

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1

Components - Panels
Please check you have all the panels listed below
2
1
2
3
Top (150 x 90cm)
Leg x 4 (73 x 6.5cm)
Extension panel x 2 (90 x 61.8cm)
underside

3
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Ruler - Use this ruler to help correctly identify the screws
Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 0845 640 0800
Please check you have all the fittings listed below
Tools required
A
D
G
E
B C
F
80mm Bolt x 8 60mm Assembly bolt x 4
Washer x 8
Cover block x 4
Spring washer x 8
13mm Nut x 8
Spanner x 1
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Ruler/tape
measure
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.

Assembly Instructions
Step 1
4
A
A
B
C
F
E
D
2
1
2
2
2
2
Step 1
Fitting bolts
Insert assembly bolt
into leg , screw bolts
into assembly bolt .
Step 2
Attaching legs
Attach four legs to
top using washer ,
nut , and spring
washer . Tighten the
bolts with spanner .
AB
B
2
2
E
D
2
1
F
C
Repeat with remaining
legs .