Argos KINGSTON 6029731 User manual

Cat. No. 6029731 KINGSTON OAKSTAIN PAIR OF CHOC CHAIRS
6029779 KINGSTON OAKSTAIN PAIR OF CREAM CHAIRS
6029803 KINGSTON WALNUTSTAIN PAIR OF CHOC CHAIRS
6029834 KINGSTON WALNUTSTAIN PAIR OF CREAM CHAIRS
5. The maximum weight of user - 100kgs
4. To avoid scratching it is recommended that you assemble the chair on a
soft level surface.

6
10 10
Components and fittings for one chair assembling.

2
E
F
G
I
A
B
H
G
F
E
I
G
F
D
I
I
C
Secure the short JCBC
screws (E) using spring
washers (F) and flat washers
(G) as show in Fig.2.
Do not fully tighten all
screws at this stage.

Dining Chair
Assembly Instructions - Please keep for future reference 603/4135
603/2333
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 25/09/12
Dimensions
Width - 44cm
Depth - 54cm
Height - 92cm
603/2900
603/0452
602/9834
603/2364

1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warnings
Care and maintenance
• Assemble this product on a flat
surface.
• Assemble all parts loosely
before tightening any bolts.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Discard all extra fittings and
keep fittings out of reach of
children.
• Unit weight: 4.9kgs.
• Maximum safe weight of user:
110kgs.
• Retain Assembly Instructions
for future reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• This product should only be
used on firm, level ground.
• Make sure the legs remain in
contact with the ground.
• Do not stand on the product.
• Please clean the unit surface
using either damp (not wet)
cloth and a mild domestic soap
solution or by using an
appropriate polish.
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on this
unit.

2
Components - Parts
Components - Fittings
Please check you have all the parts listed below
Please check you have all the fittings listed below
Backrest
(36 x 10 x 92cm)
M6 x 85mm Bolt x 4
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
1Seat
(43.5 x 41 x 9.5cm)
2Leg x 2
(3 x 3 x 43cm)
3
A
Washer x 9
D
M6 x 55mm Bolt x 5
B
Allen key x 1
E
Spring washer x 9
C
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170

3
Place the backrest on a
flat protected surface.
Position the seat on
the backrest as
shown and fix using bolts
& , spring washers
and washers . Tighten
bolts using allen key .
Important:
Do not fully
tighten bolts at
this stage.
Assembly Instructions
Step 1
Step 2
2
1
2
2
3
3
3
B
E
B
B
B
B
A B
D
C
D
C
D
C
D
DC
B DC
D
C
C
Attaching backrest
2
1
A
D
C
A
D
C
A
C
D
A
D
C
A
D
C
A
D
C
B
D
C
2
1
B
D
C
Attaching legs
Place the seat upside
down on a flat protected
surface.
Insert the legs into the
holes of the seat as
shown and fix using bolts
, spring washer and
washers . Tighten the
bolts using allen key .
Important:
Do not fully
tighten bolts at
this stage.
2
3
B
E
C
D

4
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
E
Aligning & securing the
legs
Carefully turn the chair
upright and place on a
flat surface.
a: Tighten all bolts using
allen key .
Note: This step is
essential to prevent the
chair from wobbling due
to uneven legs.
b: Carefully sit on the
chair and make
adjustments to ensure
the legs are flat even on
the floor.
c: After the sitting test,
re-tighten bolts again if
any adjustment is
needed.
Note: It is highly
recommended to
re-tighten all bolts after
using the chair for 7
days.
Note: Keep allen key to
re-tighten bolts when
required.
E
Assembly is complete.
E
Assembly Instructions
Step 3
a:
b:
c:

Cat.No 6030940 KINGSTON SOLID WOOD WANUTSTAIN DINING TABLE 150
6029669 KINGSTON SOLID WOOD OAKSTAIN DINING TABLE 150

JCBC
Alen Key