Argos 875/5694 User manual

Frosted Glass Sliding Door Media Unit
Dimensions
Width - 92cm
Depth - 24cm
Height -123.4cm
Issue 1 - 9/07/08
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
875/5694
Assembly Instructions - Please keep for future reference

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below

Please check you have all the panels listed below
2
Top
1
(19.7x92.1cm)
Base
2
(24x92.1cm)
Left side panels
3
(18.5x119.7cm)
Right side panels
4
(18.5x119.7cm)
Back Panel
6
(81.6x122.8cm)
Fixed Shelf
5
(13.2x79.1cm)
Adjustable Shelves x 6
7
(13.2x78.8cm)
Sliding Doors x 2
8
(40.9x120.3cm)
Components - Panels If you have damaged or missing components,
call the Customer Helpline: 08456 400800

3
Please check you have all the ttings listed below
Cam Bolt x 4
A
Cam Lock x 4
B
38mm Large screws x 6
C
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
Components - Fittings
12mm Screw x 4
D
Dowel x 8
E
Tacks x 28
F
Shelf support X 24 Glue x 1
Wall Strap X 2 12mm Screw X 2
Plug X 2 32mm Screw X 2
G
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
01 02 03 04 05 06 07 08 09 0 100 110 120 130 140 150
01 23 45 6
Ruler - Use this ruler to help correctly identify the screws
100 20 30 40 50 60 70 80 90 100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
J
H

4
Assembly Instructions
Step 1
3
4
A
A
Attaching side panel
Insert the cam bolts
into the panel & .
3 4
A
H
B
E
5
4
3
B
Fixed Shelf Assembly
Place cam locks into
xed shelf .
Ensure arrow on the
cam locks face towards
the side panel to be
attached.
Attach side panels using
dowels and a dab of
glue .
Do not force,if shelf
will not t easily check
arrows on cam locks
are facing the correct
direction and try again.
Turn cam locks
clockwise until tightened.
Be careful not to over-
tighten as this can break
the lock.
B
5
H
E
B
B
Step 2
Foiled edges facing front
Foiled edges facing front
Foiled edges facing front

5
1
3
4
1
Assembly Instructions
Step 3
Attaching top panel
Screw 2 x cam bolts
into the top .
1
A
A
B
Step 4
Attaching the Top
Place cam locks into
side panels and .
Ensure arrow on the cam
locks face towards the
top to be attached.
Attach top using dowels
and a dab of glue .
Do not force, if the top
will not t easily check
arrows on cam locks
are facing the correct
direction and try again.
Turn cam locks
clockwise until tightened.
Be careful not to over-
tighten as this can break
the lock.
H
B
E
B
B
3 4
1
E
B
E
H
Foiled edges facing
front

6
Assembly Instructions
Step 5
2
2
Step 6
Fixing back panel
Attach the backboard
using pins and
screws .
Ensure the backboard is
the right way up so the
screws attach to the xed
shelf .
5
F
D
6
Base Assembly
Attach the base to
the unit using large
screws .
2
C
C
C
C
D
F
6
2
Foiled edges
facing front

Assembly Instructions
Step 8
7
Step 7
Attach the shelf supports
to the unit in the
desired location,
depending on the media
to be stored.
Then install the
adjustable shelves .
G
7
Glass door assembly
Attach the sliding doors
to the unit in the
corresponding grooves,
ensure the nger grip is
facing towards the sides
of the unit, as per the
picture.
One door needs to slide
behind the other.
8
8
7
7
7
7
7
8
G

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Nylon strap
Screw
Wall
Screw+Plug
Back panel
Top
Note: Wall plugs supplied are
for solid walls only.
The correct type of xing must
be used for your wall, seek
professional advice if in doubt.
8
Assembly Instructions
Step 9
Finishing the unit
NOTE: It would be useful
to ask someone to help
you at this stage.
It is strongly
recommended that the
unit is attached to the
wall using Wall Strap .
Drill a hole in the wall at
an appropriate position
and insert a suitable
Wall plug .
To secure the unit, x
wall Strap to the wall
using a suitable Screw .
Assembly is complete.
J
J
Warning:
Before drilling,
check wall for
hidden pipes
and cables.

9