Argos Malibu 259/7937 User manual

MADE IN
BRITAIN
Dimensions
Width - 75cm
Depth - 40cm
Height - 41cm
Malibu - Media Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 04/09/14
Important - Please read these instructions fully before starting assembly
ALR3036
259/7937
238/3172
228/8284
259/8967
275/3953
278/5079
iSSUE 2 - 19/03/14 - All panel codes have been updated.
Drawer Sides now 370 x 124mm.
Drawer Back now 676 x 124mm.
Drawer Base now 687 x 367mm.
Changed runners to metal sliders, added 4 Wedgefixes, 4 Plastinails, 4 Skinny Euros and 2 M4x9 Machine Screws.
Plinth has been moved back.
Issue 3 - 03/09/14 - Changed Drawer Back description to W676-124BCK.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 15.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
12 3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
4
Divider (D2866A)
(92 x 372mm)
5
6
7 8 9
11
10
12
Drawer Base (T687-367)
(687 x 367mm)
Back (X568-318)
(568 x 318mm)
Drawer Back (W676-124BCK)
(676 x 124mm)
Left Drawer Side
(W370-124LH)
(370 x 124mm)
Right Drawer Side
(W370-124RH)
(370 x 124mm)
Top (D2863A)
(747 x 396mm)
Horizontal (D2867A)
(708 x 373mm)
Rail (D2868A)
(708 x 92mm) x 3
Drawer Front (D2869A)
(704 x 190mm)
Left Side (D2864A)
(396 x 394mm)
Right Side (D2565A)
(396 x 394mm)

Please check you have all the fittings listed below
Tools required
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
3
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
A
Wooden dowel (F22) x 11
B
Metal dowel (F901) x 8
C
D
Large locking
nut (F900) x 6
E
Small locking
nut (F3) x 2
F
G H I
J
Nail (F51) x 12
25mm Screw (F50) x 2
K
Handle (F631) x 2
40mm Screw (F910) x 10
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
45mm Screw (F65) x 2
O
Wedgefix (F639) x 4
Knock-in Peg (F171GY) x 4
Drawer runner (F1004) x 2
L
9mm Screw (F74) x 2
M
9mm Screw (F73) x 4
N
Plastic Nail (F91) x 4

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
B
7
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
F
8
9
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
9
7
F
F
8
9
B
B
7
B
B
F
Step 2
Step 3
F
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the small groove is on the inside, as shown.
FF
89
9
87

Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
10
8 9
7
11
8 9
10
11
11
C
8 9
7
8
10
9
C
C
C
C
10
9
8
11
Step 6
Attach the handles
Attach the handles to
the drawer front
using 2 screws .
K
I
7K
I
K
I
7
O
Fit the wedgefixes
Turn the drawer
assembly over and slide
4 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
O
O
OO
O
Step 7
Note: Do not
overtighten the screws.

Assembly Instructions
6
Step 8
A
E
Finished
front edge
E
1
Finished
front edge
1
Finished
front edge
M
J
E
Prepare the left side
a: Place a runner on
the left side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
Tap a wooden dowel
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
1
M
M
E
1
1
J
Ja:
b: 10mm
A
A
1
M
J
M

Finished
front edge
Finished
front edge
H
H
A
Assembly Instructions
7
Step 9
A
E
E
Finished
front edge
2
2
A
Prepare the horizontal
Tap 2 wooden dowels
into the horizontal .
Step 10
A
4
plain chipboard surface
4
Finished
front edge
Fit the horizontal to
the right side
Push the horizontal
onto the right side
and secure with 2
screws .
4
plain chipboard surface
2
Step 11
4
2
H
Prepare the right side
a: Place a runner on
the right side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
Insert 2 large locking
nuts into the right
side .
Tap a wooden dowel
into the right side .
2
M
M
E
2
2
J
J
A
2
Finished
front edge
M
J
a:
b:
M
J
M

H
H
H
Assembly Instructions
8
Step 12
Step 13
A
Prepare the 3 rails
Tap 2 wooden dowels
into each of the 3 rails . .
A
6
Finished
front edge
A
6
plain chipboard surface
Fit the 3 rails to the
right side
Push the 3 rails onto
the right side and
secure with 3 screws .
6
2
H
Step 14
Fit the left side
Push the left side
onto the assembly and
secure with 5 screws .
Carefully stand the
unit up in preparartion
to fit the top.
1
Note: Support the rail at
the back of the unit until
the left side has been
fitted in the next step.
plain chipboard surface
plain chipboard surface
H
H
H
H
H
H
1
Warning: The
unit is heavy.
Lift with care.
x 3
6
6
2
plain chipboard surface
6

Assembly Instructions
9
Step 15
Prepare the divider
Tap a wooden dowel
into the divider .
Insert 2 large locking
nuts into the divider
. .
Step 16
Fit the divider to the
top
Push the divider
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 17
plain chipboard surface
B
B
B
B
B
B
Finished
front edge
3
Prepare the top
Screw 6 metal dowels
into the top .
B
3
E
E
Finished
front edge
A
A
5
5
E
5
E
B
5
3
5
3
E
5
Finished
front edge
E