Argos FUTON 656/0032 User manual

FUTON BUNK BED
Assembly Instructions - Please keep for future reference 656/0032
Important - Please read these instruction fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 02/01/10
Open Dimensions
Width - 201cm
Depth - 177.5cm
Height - 165cm
Close Dimensions
Width - 201cm
Depth - 164cm
Height - 165cm

1
Safety and Care Advice
IMPORTANT – READ CAREFULLY – RETAIN FOR FUTURE REFERENCE
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
away from the work area, small
parts could choke if swallowed.
space to layout the parts before
starting.
room) as possible.
surface to avoid damaging the
easier with 2 people.
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
carefully and responsibly.
and mild detergent, do not use
bleach or abrasive cleaners.
there are no loose screws on
this unit.
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Note:
this could cause damage.
Do not stand on the product,
Keep These Instructions For Future Reference
This product complies with
EN 747-1:2007
Argos plc
489-499 Avebury Boulevard
Central Milton Keynes
MK9 2NW
All assembly fastenings
should always be tightened
properly and that care should
be taken that no fittings are
loose.
The bunk bed or high bed
should not be used if any
structural part is broken or
missing.
The high beds and the upper
bed of bunk beds are not
suitable for children under six
years due to the risk of injury
from falls.
Children can strangle in
items such as ropes, strings,
cords, harnesses and belts
attached to or hung on a bunk
bed/ high bed.
Recommended size of the
mattress(es):
W75 x L175 x D18cm.
Warning: “Children can
become trapped between the
bed and the wall. To avoid risk
of serious injury the distance
between the top safety barrier
and the wall shall not exceed
75 mm or shall be more than
230mm”.

Components - Panels
Please check you have all the pan els listed below
2
Back safety barrier x 1
(190.4 x 37cm)
10Front safety barrier x 1
(154 x 37cm)
11 Spring hinge X 1
(46 x 16cm)
12
Spring hinge X 1
(46 x 16cm)
13 Futon frame X 1
(190 x 69.8cm)
14Futon frame X 1
(190 x 69.8cm)
15
16Ladder X 1
(144 x 34.7cm)
Metal leg x 4
( Ø4.8 x 165cm)
1Headboard x 2
(89.9 x 39.3cm)
2Lower footboard x 1
(88.7 x 20cm)
3
Lower footboard x 1
(88.7 x 20cm)
4Filler bar x 2
(90.1 x 3cm)
5Top cross bar x 1
(190.7 x 4cm)
6
ARGOS
Bottom cross bar x 2
(190.7 x 4cm)
7Top cross bar x 1
(190.7 x 4cm)
8Bed slats x 1
(190 x 93.4cm)
9

Tools required
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 120105 115 125 130 135 140 145 150 155 160 165 170
3
19mm Washer x 11
A
D
H
B
F
C
G
16mm Washer x 24
M6 x 55mm Bolt x 11
M6 x 20mm Bolt x 8
M8 x 20mm Bolt x 4
18mm Washer x 18
M6 x 65mm Bolt x 24
E
M8 x 65mm Bolt x 4
I
M8 x 50mm Bolt x 8
J
M8 Nuts x 8
K
M6 x 35mm Bolt x 2
L
M6 Nuts x 2
M
Plastic cover x 14
Allen key M4
(included)
Allen key M5
(included)
Spanner M6
(included)
Spanner M8
(included)
Screwdriver
(not included)
Rubber Mallet
(not included)

Assembly Instructions
Step 2
4
Attaching headboard
Attach headboard Ⓑ to
metal leg Ⓐ by using 2
pcs of bolts .
Headboard should
be faced toward to other
side.
Step 3
Attaching lower
headboard
Attach lower headboard
to metal leg by
using 2 pcs of bolts
and 2 pcs of washers .
Headboard should
be faced toward to other
side.
2
Step 4
Attaching metal leg
Attaching the other
metal leg to the
headboard by using
2 pcs of bolts .
A
1
A
1
3
1
2
3
2
3
1
Step 1
Note: Please ensure
the WASHER is curving
in facing the hole
before assembling.
The washer curving out
facing the hole is incorrect.
The washer curving in
facing the hole is correct.
1
2
A
A
B
B
C
C
A
A
2
1
A
2
1
2
1
2
1
B
3

Assembly Instructions
Step 5
Attaching metal leg
Attach metal leg to
the lower footboard
by using 2 pcs of screws
and 2 pcs washers .
Attaching Filler bar
Attach filler bar to
headboard by using
3 pcs of bolts .
2
Step 6
5
B
5
Step 7
33
B
C
B
C
D
D
D
2
1
2
A
A
5
Attaching headboard
Attach headboard to
metal leg by using 2
pcs of bolts .
2
A
1
D
1
2
2
1
2
1
1
C

Step 8
Step 9
Step 10
Assembly Instructions
4
1
B
B
C
C
A
A
2
1
Attaching lower
footboard
Attach lower footboard
to metal leg by
using 2 pcs of bolts
and 2 pcs of washers .
Footboard should be
faced toward to other
side.
1
B
4
Attaching metal leg
Attaching the other
metal leg to the
headboard by using
2 pcs of bolts .
A
1
2
4
Attaching lower
footboard
Attach lower footboard
to metal leg by
using 2 pcs of bolts
and 2 pcs of washers .
B
4
4
B
C
B
C
1
2
6
A2
1
C
4
1
C

Assembly Instructions
Step 11
Step 12
Step 13
Attaching top cross
bar
Two people are required
here.
Attach top cross bar
to the unit by using 2
pcs of bolts and 2 pcs
of washers .
Attaching bottom
cross bar
Two people are required
here.
Attach bottom cross bar
to the unit by using 2
pcs of bolts and 2
pcs of washers .
D
D
D
2
5
Attaching filler bar
Attach filler bar to
headboard by using
3 pcs of bolts .
2
5
D
B
C
B
C
1
4
6
4
6
B
B
CB
C
1
4
7
6
7
B
Warning:
The unit is
heavy.
Lift with care.
Warning:
The unit is
heavy.
Lift with care.
7
C
C

Assembly Instructions
8
Step 15
Join another cross
bars
Two people are required
here.
Join another 2 pcs of
cross bar and to
the unit by using 4 pcs
of bolts and 4 pcs of
washers .
Step 14
Join both cross bars
Two people are required
here.
Join both cross bars
and to the
completed units by
using 4 pcs of bolts
and 4 pcs of washers .
1
1
C
B
C
B
7
6
B
C
B
C
C
B
B
C
1
1
8
6
7
B
78
B
Warning:
The unit is
heavy.
Lift with care.
Warning:
The unit is
heavy.
Lift with care.
7
4
3
4
3
C
C

Assembly Instructions
Attaching bed slats
Two people are required
here.
Use a rubber mallet(not
supplied) gently tap
each slat lock onto
cross bars and .
Recommend 2 persons
for assembly.
Step 17
9
Step 16
Attaching bed slats
Spread out the bed slats
,make sure each
hook of slat point
downwards as shown.
9
8
9
6
9
4
3
68

Assembly Instructions
Step 18
Attaching safety
barrier
Two people are required
here.
Attach safety barrier
to this unit through 2
pcs of bolts and 2 pcs
of washers .
Fix 3 pcs of bolts and
washers to this safety
barrier through top
cross bar .
Fixing safety barrier
Fix safety barrier to
the unit throush 3 pcs of
bolts with tool.
Step 19
10
10
E
10
D
10
EF
E
F
10
8
8
1
1
1
1
8
10
G
D
8
10
F
10
8
G
D
D

Assembly Instructions
Step 20
Attaching ladders
Ladder can be fixed to
either left or right side.
11
OPTION 1
OPTION 2

Assembly Instructions
Step 22
Attaching front safety
barrier
Secure safety barrier Ⓚ
underside by using 2
pcs of bolts and 2
pcs of washers with
tool as shown.
12
Step 21
Attaching front safety
barrier
Two people are required
here.
Attach front safety
barrier to top bunk
by using one of bolt
and washer from side
and 1 pcs of bolt and
washer from bottom
with tool as shown.
11
E
E
11
D
F
G
G
E
F
G
E
11
6
G
G
D
D
11
6
G
E
G
D

Assembly Instructions
Step 24
Attaching spring
hinge
Attach 1 pc of spring
hinge by using 2 pcs
of bolts and washer
with tool.
Step 23
Attaching spring
hinge
Attach 1 pc of spring
hinge by using 2 pcs
of bolts and washer
with tool.
12
H
H
13
3
4
4
3
G
G
13
12
H
G
3
4
13
G
H

Step 26
Attaching futon frame
Fix another side of the
futon frame through
spring hinge by
using 2 pcs of bolts ,
washers , and nuts
with spanner and
tool.
Step 25
Attaching futon frame
Lay down futon frame
on spring hinge
by using 2 pcs of bolts
, washers , and
nuts with spanner and
tool.
Assembly Instructions
1413
I
14
12
I
FG
J
FG
J
14
I
F
G
J
13
14
I
F
G
J
12
14

Step 28
Attaching futon frame
Fix another side of the
futon frame through
spring hinge by
using 2 pcs of bolts ,
washers , and nuts
with spanner and
tool.
Step 27
Attaching futon frame
Lay down futon frame
on spring hinge
by using 2 pcs of bolts
, washers , and
nuts with spanner and
tool.
Assembly Instructions
15
I
15
I
12
FG
J
FG
J
12
15
I
F
G
J
15
I
F
G
J
15

Step 29
Fixing ladder ( for
right side )
a: Attach the ladder
onto this unit as shown.
b: Fix the ladder to
the unit by using 2 pcs
of bolts and nuts
with tool.
Assembly Instructions
16
a:
KLb:
M
M
M
7
6
1
Step 30
6
16
M
M
M
Attaching plastic
covers
Attach 14 pcs of plastic
covers as shown.
M
16
L
K
K
L

Step 31
Putting futon frame
in positon
a: Lift up the front futon
frame.
b: Push it inward.
c: Put down the futon
frame front to lock in
position.
Assembly Instructions
14
17
15
15
a:
b:
c:
15

Step 32
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
18
Step 33
Assembly is
complete.
Assembly is
complete.
For safety reason,please
ensure the top of the
mattress shall not come
above the line marked
on the top bunk.
WARNING:
TOP OF THE MATTRESS SHALL
NOT COME ABOVE THE LABEL
MARKED ON THE BED.
MAX:200mm

Futon Bunk Bed
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 06/11/13
Dimensions
Width - 200cm
Depth - 99/174cm
Height - 165cm
IMPORTANT NOTE:
The top surface of the mattress
should not come above this line.
758/4512