Argos Capella 249/6674 User manual

MADE IN
BRITAIN
Dimensions
Width -123.5cm
Depth - 39cm
Height - 74.4cm
Capella - 4 + 4 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 6 - 28/03/14
Important - Please read these instructions fully before starting assembly
249/6674
247/6058
268/2433
ALR2994
03/08/11 - Drawer assembly changed to Knock-in Pegs.
Drawer Sides and Drawer Back changed to take Knock-in Pegs.
Upright corrected to D1041A.
25/10/11 - Changed Step 7 to say to use the 1st hole and the 3rd hole of the runner.
25/10/11 - Recreated the AI to meet the set standards and corrected the mistakes.
Changed Step 9 to say to use the 1st hole from the front of the runner, as requested.
246/7081
Issue 5 - 16/05/12 - New Argos code added
Issue 6 - 28/03/14 - Drawer sizes increased
16 drawer wedges added.
5 plastinails added.
Old cat codes removed and new ones added.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 41kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
1
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
5
2
98
6
10
12
Left Side (D1039A)
(744 x 390mm)
Left Hand Drawer Front (D1044A)
(599 x 157mm) x 4
Back (X832A)
(1229 x 646mm)
Rail (D1043A)
(1205 x 103mm) x 2
Right Side (D1040A)
(744 x 390mm)
Right Hand Drawer Front (D1045A)
(599 x 157mm) x 4
Upright (D1041A)
(621 x 368mm)
Support (D1046A)
(300 x 85mm)
7
13
4
11
3Top (D1042A)
(1205 x 369mm)
2
Drawer Back (W564 - 124)
(564 x 124mm) x 8
Drawer Base (T575 - 367)
(575 x 367mm) x 8
Left Drawer Side (W370-124LH)
(370 x 124mm) x 8
Right Drawer Side (W370-124RH)
(370 x 124mm) x 8

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 26
D E
Large locking
nut (F900) x 10
F
G H I
K
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Small locking
nut (F3) x 16
C
Nail (F51) x 22
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Drawer runner (F1004) x 16
Handle (F930) x 8
25mm Screw (F50) x 16 9mm Screw (F74) x 16 9mm Screw (F73) x 32
45mm Screw (F65) x 3
L
Knock-in Peg (F171GY) x 32
N
Plastic Nail (F91) x 5
M
Wedgefix (F639) x 32

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 4
x 4
Prepare the 4 left
hand drawer fronts
and 4 right hand
drawer fronts
Screw 2 metal dowels
into the holes shown on
the back of each drawer
front and .
Note: Tighten the metal
dowels up fully against
the panels.
B
6
B
7
F
B
B
6
7
B
B
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
E
9
10
Step 2
x 8 x 8
E
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
EE
910
Step 3
x 8
B
E
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts and .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
9
10
6
E
E
9
10
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the small groove is on the inside, as shown.
10
96 7
7
Note: The right drawer
front has a shallow
identification mark.

Assembly Instructions
5
Step 4
Attach the handle
Attach a handle to
each drawer front
and using 2 screw .
K
G
Step 6
6
x 8
L
L
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
fronts and .
Step 5
Fit the drawer back
Fit the drawer back .
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
11
9 10
6
8
9 10
11
8
8
L
x 8
x 8
x 8
L
L
9
11
11
10
9
9 10
8
M
Fit the wedgefixes
Turn the large drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
M
M
M
M
M
Step 7
10
7
6 7
and
7
GG
K
6 7
and

Profiled
front edge
Profiled
front edge
Profiled
front edge
Assembly Instructions
6
Step 8
Profiled
front edge
I
J
I
J
Back edge
I
J
Prepare the left side
a: Place 4 runners on
the left side . Slide
back the top of the
runner and use the 1st
hole from the front to fit
the 1st screw .
b: Slide the runner back
the other way and use
the 3rd hole from the
back to fit the 2nd screw
.
c: Screw 4 metal
dowels into the left
side .
a:
b:
c:
1
I
B
1
I
J
I
J
I
J
I
J1
1
1
I
I
I
I
B
B
B
B

Assembly Instructions
7
Step 9
Prepare the right side
a: Place 4 runners on
the right side . Slide
back the top of the
runner and use the 1st
hole from the front to fit
the 1st screw .
b: Slide the runner back
the other way and use
the 3rd hole from the
back to fit the 2nd screw
. .
c: Screw 4 metal
dowels into the right
side .
Profiled
front edge
I
J
Back edge
I
J
I
J
2
I
B
2
a:
b:
c:
2
2
2
I
J
I
J
I
J
I
J
I
I
I
I
B
B
B
B
Profiled
front edge
Profiled
front edge
Profiled
front edge

Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 10
Prepare the upright
a: Place 4 runners on
the upright . Slide
back the top of the
runner and use the 1st
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the upright .
Insert 2 large locking
nuts as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Turn the upright over.
c: Repeat the
instructions above to fit 4
runners onto the other
side of the upright
using screws .
I
J
4
I
D
I
J
4
Turn the upright over
4
a:
b:
c: I
J
I
J
I
J
I
J
Finished
front edge
I
I
I
I
Finished
front edge
D
4
4
Profiled
front edge
I
J
I
J
I
I
J
I
J
I
J
4
4
D
D
J
I
I
I
I

A
A
Assembly Instructions
9
Prepare the top
Tap 4 wooden dowels
into the top as
shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the top .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Screw 2 metal dowels
into the top .
10mm
A
A
3
3
D
D
B
Join the upright and
top
Push the top onto
the upright as
shown.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the upright .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 12
3
4
D
D
4
B
3
D
D
D
D
A
A
Finished
front edge
3
B
B
plain chipboard surface
3
Finished
front edge
Finished
front edge
4
Step 11