Argos 600/037 User manual

Executive Gas Lift Bar Stool
Assembly Instructions - Please keep for future reference 600/0372
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Issue 1 - 28/04/14
Dimensions
Width - 51cm
Depth - 51cm
Height - 87.5-107.5cm
600/1522
239/6011

1
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Parts of the assembly will be
easier with 2 people.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Do not stand on the stool.
• Do not use this stool as step
ladder.
• To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Unit weight: 7.68 kgs.
• Maximum safe weight of user:
110kgs.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.

2
Components - Parts
Please check you have all the parts listed below
If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 640 0800
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Components - Fittings
Please check you have all the fittings listed below
Seat
(51 x 44.5 x 36cm)
M6 x 16mm Bolt x 4
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
1Upper leg
(29.5 x 21.5 x 40.5cm)
2Gas lift
(Ø5 x 46-67cm)
3
A
Washer x 4
B C
Base
(Ø50 x 9.3cm)
5
Decor ring
(Ø7.5 x 2cm)
4
Allen key x 1

3
Assembly Instructions
Step 1
Attaching upper leg
Place the seat upside
down on a raised, flat
and protected surface.
Position the upper leg
and make sure that the
lever is at your right hand
side as shown in the
diagram.
Secure using bolts and
tighten bolts using allen
key .
B
A
1
2
Step 2
A
B
A
B
A
B
A
B
2
2
1
1
A
B
Lever
3
4
5
Plastic tip
Attaching gas lift
Place the base on a
flat protected surface.
Position the decor ring
on the base and insert
the gas lift into the
decor ring and hole of
the base.
Important:
Remove plastic tip
cover on gas lift
before
assembling.
5
4
3

4
Assembly Instructions
Step 3
Step 4
Assembly is complete.
Gaslift operation
To adjust the seat higher,
lift up the lever under the
seat and release at
desired height.
To lower the seat, lift up
the lever while seated on
the stool.
Attaching the seat
Position the seat as
shown and insert the gas
lift into the upper leg
. Secure by pressing
down the seat firmly.
3
2
Lever
2
3
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800

Depth -54.5cm
Width - 52cm
Height - 84/106cm
– Please read these instructions fully before starting assembly
-
Dimensions
Important
If you need help or have damaged or missing parts, call the
Please keep for future reference 600/1522
Assembly Instructions
Executive Bar Stool With Back Rest
Customer Helpline: 0845 640 0800

rTFUIJTQSPEVDUPOMZGPSr
1
• From time to time check that
the product during assembly,
this could cause damage.
page 2.
r$IFDLZPVIBWFBMMUIF
components and tools listed on
r3FNPWFBMMàUUJOHTGSPNUIF
plastic bags and separate them
into their groups.
r,FFQDIJMESFOBOEBOJNBMT
away from the work area, small
parts could choke if swallowed.
r.BLFTVSFZPVIBWFFOPVHI
space to layout the parts before
starting.
r%POPUTUBOEPSQVUXFJHIUPO
r"TTFNCMFUIFJUFNBTDMPTF
to its nal position (in the same
room) as possible.
r"TTFNCMFPOBTPGUMFWFM
surface to avoid damaging the
unit or your oor.
r1BSUTPGUIFBTTFNCMZXJMMCF
easier with 2 people.
r8FEPOPU
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
r%JTQPTFPGBMMQBDLBHJOH
carefully and responsibly.
Care and maintenance
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Note:
there are no loose screws on
this unit.
Care and maintenance
From time to time check that
• To avoid any risk of suffocation to
animals or children dispose of the
plastic bags immediately
.
discarded with household
waste. Take to your local
authority waste disposal centre.
As with all surfaces clean with a
do not use bleach or abrasive
damp cloth and mild detergent,
This product should not be
Safety during use
r%POPUTUBOEPOUIJTDIBJS%P
. U
rTFUIJTQSPEVDUPOMZGPS
seating one person at a time.
OPUVTFUIJTDIBJSBTBTUFQMBEEFS .
r%POPUVTFUIJTDIBJSVOMFTTBMM
bolts screws and knobs are firmly
secured.
.
.
r"UMFBTUFWFSZNPOUITDIFDL
4,
BMMCPMUTTDSFXTBOELOPCTUPCF
, ,
TVSFUIFZBSFUJHIU
.
,
,
rGQBSUTBSFNJTTJOHCSPLFOPS
I
EBNBHFEPSXPSOTUPQVTFPG
UIJTQSPEVDUVOUJMSFQBJSTBSFNBEF
VTJOHGBDUPSZBVUIPSJFEQBSUT
z
r'BJMVSFUPGPMMPXUIFTFXBSOJOHT
could result in serious injury.
,
• •
•
products.

Back x 1
2
( 220mm )
Gas lift x 1
Cover x 1
( 52X32cm )
Components -
Parts
3
1
5
4
Please check you have all the parts listed below
2
Seat support x 1
Fittings If you have damaged or missing components,
call the
Components -
Please check you have all the fittings listed below.
Customer Helpline:0845 640 0800
22mm Bolts x 4
A
AA
B
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110
105 115 120 125 130 135 140 150 145 160 155 165
M6 Allen key (supplied)
Tools required
The quantities below are the correct amount to complete the assembly
In some cases more fittings may be supplied than are required.
Note:
6Base x 1 ( D500mm )
Seat x 1 ( 39X39cm )
Washers x 4
A
C
40mm Bolts x 3

3
Assembly Instructions
Fitting the gaslift
a:
Take off the cap on the top
of gaslift .
a:
b:
2
B
3
6
5
b: Insert the gaslift into the
base . Then slide the cover
5
over the top.
3
Step 1
Fitting the seat
Use the bolts to fix the
seat .
Step 2
B
2
6
5
5
inserted and well fitted.
Ensure the gas lift is
NOTE:
fully

4
Fitting the seat support
onto the base unit.
Carefully locate the seat
Assembly Instructions
to fix the seat support .
Step 3
2
2
Step 4
Fitting the Unit
Use the bolts and washers
A
C
4
A
C4