Argos New Sywell 427/1237 User manual

MADE IN
BRITAIN
Dimensions
Width - 101.9cm
Depth - 59.5cm
Height - 171.1cm
New Sywell - 2 Door Sliding Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 28/05/15
Important - Please read these instructions fully before starting assembly
ALR3192
427/1237
425/8700
427/1770
427/1244

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 62kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Rule
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)

Components - Panels
Please check you have all the panels listed below
2
12 3
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
4
5
Left Side (DF3581)
(171.1 x 59.2cm)
Right Side (DF3582)
(171.1 x 59.2cm)
Top/Base (DF3584)
(98.9 x 59cm) x 2
Shelf (DF3587)
(48.7 x 49cm) x 2
Rail (DF3588)
(48.7 x 12cm) x 2
Divider (DF3585)
(165.6 x 49.6cm)
Door (DF3583)
(164.7 x 50.4cm) x 2 Back (X1682-506)
(168.2 x 50.6cm) x 2
689
Hanging Rail (FHR481)
(48.1cm long) x 2
7

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 16
C
D E F
G
P
98.7cm Track (F221) x 4
O
Bottom glide
(F952) x 4
N
B
Metal dowel (F901) x 12
Large locking
nut (F900) x 24
Buffer bracket
(F261) x 1
Q
Top glide
(F956) x 4
M
Mushroom Head Pin (F260) x 4 Double metal dowel (F566) x 4
S
Rail Holder
(F891) x 4
H
Nail screw (F277) x 10 Back holder (F276) x 10
These can
also be round
K
J
40mm Screw (F910) x 4
13mm Screw (F63) x 18
25mm Screw (F95) x 4
R
UT
W
Handle (F315) x 2
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Large wooden dowel (F40) x 2
Feet (F854) x 2
I
Nail (F51) x 36
L
V
Plastic Nail (F91) x 4
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
25mm Screw (F50) x 2 13mm Screw (F79) x 8

A
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
A
O
Prepare the top and
base
Place 2 plastic tracks
down onto each of the
top and base
panels, making sure that
they are flush with the
edges of the panel.
Gently tap along the
length of the plastic
tracks until they are
fitted flat to the surface
of the panel.
Turn the top and the
base panels over
Tap 4 wooden dowels
into each of the top
and base panels.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into each of the
top and base
panels.
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
10mm
A
4 4
O
4
4
O
O
Turn the top and
the base over
C
4 4
x 2
x 2
C
O
O
Finished
front edge
4
C
C
C
C
A
A
Finished
front edge
4

Finished
front edge
A
A
Assembly Instructions
5
Step 2H
S
H
S
H
H
S
Turn the divider over
A
A
H
H
S
Finished
front edge
Prepare the divider
Tap 4 wooden dowels
into the divider .
Fit a rail holder by
screwing through the top
hole with screw and
into the mark hole drilled
in the divider . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
Turn the divider over
Fit another rail holder
by screwing through the
top hole with screw
and into the mark hole
drilled in the divider .
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
A
3
S
H
H
3
S
H
H
3
3
3

E
E
Assembly Instructions
6
Step 3
E
E
Note: The plastic
tracks must be on
the inside surfaces
of the top and base
Fit the top and base
to the divider
Attach the top and
the base to the
divider using 4
screws .
4
4
3
E
4
4
3
Top
Base
C
C
A
A
C
C
A
Prepare 1 of the
shelves
Tap 2 wooden dowels
into the shelf .
Insert 4 large locking
nuts into the shelf .
5
C5
5
Finished
front edge
Step 4

D
R
Assembly Instructions
7
Step 5
D
5
Finished
front edge
Fit the shelf
a: Push the shelf
onto the divider .
Tap 2 double metal
dowels through the
divider and into the
shelf until they
‘’bottom out’’.
Tap 2 large wooden
dowels through the
divider and into the
shelf until they
‘’bottom out’’.
b: Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
5
3
R
3
5
3
5
C
C
5
a:
b:
3
R
D
C
R
D
Finished
front edge
Prepare the left side
Screw 6 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Fit a rail holder by
screwing through the top
hole with screw and
into the mark hole drilled
in the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
B
1
B
B
B
B
B
B
B
H
H
S
Step 6
1
S
H
H
1

Assembly Instructions
8
Step 7
R
a:
R
3
Fit a rail
a: Tap 2 double metal
dowels through the
divider and into a rail
. until they ‘’bottom
out’’.
b: Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the rail .
Note: Support the rail
until the left side has
been fitted in the next
step.
R
3
6
C
6
b:
6
Finished
front edge
Plain chipboard
surface
x 2
Prepare the 2 rails
Insert 4 large locking
nuts into each of the
2 rails .
C
6
C
C
C
CFinished
front edge
6
Plain chipboard
surface
Step 8

Assembly Instructions
9
Step 9
6
1
5
4
4
a: P
a: P
Fit the left side
a: Push the left side
onto the assembly.
Tap 2 mushroom head
pins into the holes on
the outside of the left
side .
b: Use a screwdriver to
tighten the 8 large
locking nuts fitted to
the top , base ,
shelf and rail .
P
1
C
4 4
5 6
A
Prepare the other
shelf
Tap 2 wooden dowels
into the shelf .
Insert 4 large locking
nuts into the shelf .
5
C5
A
A
C
C
C
C
5
Finished
front edge
Step 10