Assa Abloy HES Aperio K100 Manual

HES®K100 Aperio®
Wireless Cabinet Lock
Installation & Operating Instructions
Product Contents
A Reader
B Lock Body
C Mechanical Key Override
D Installation Template
E Double Door Bracket
F Strike Plate
G Threadlock Pillow pack
H 2X AA Lithium Batteries*
*AA Lithium Batteries required. Use of other
types of batteries, such as Alkaline, will
significantly decrease battery life.
Diagram 1: Product Components
A
D
EF
GH
I: Hardware
a
c
b
d
e
f
g
hi
B
C
IHardware:
a. 2-56 X 7/16" 2x
b. 8-32 X 5/16"
c. 6-32 X 5/16" 3x
d. 6 X 1/2" 6x
e. 8-32" X 2-3/4" 2x
f. 8-32" X 1-3/4" 2x
g. 8-32" X 2-1/2" 2x
h. 8-32" X 3" Rod
i. 8-23 Nut
1 of 12

Orientation A
Orientation B
Orientation C
Lock Orientation Options
Recommended Tools
• Flathead Drivers – 3/32", 3/16"
• Drill & Drill Bits – 1 /16", 3/16", 1 /2"
• Phillips Drivers – PO, P2
• Pencil
• Wire Stripper
• Level
• Square
• Ruler
• Punch
• Scissors
Diagram 2: Orientation Options
2 of 12

Shaft Length
Door Thickness Shaft Used
1/16" – 1/2" L1
> 1/2" – 1-1/2" L2
>1-1/2" – 2-1/4" L3
Hardware Specifications
Micro USB Port
For emergency power & local
(hard wired) firmware updates,
use micro USB port located on
the side of the K100 reader.
Mounting Screw Length for Various Door Thickness
Door Thickness Reader Mounting Cut to Approximate
Screw Length Lock Mounting Cut to Approximate Screw Length
1/16" Coupling Nut & 3" Rod 10/16" 8-32 X 1-3/4" Break Away 1-1/16"
1/4" Coupling Nut & 3" Rod 13/16" 8-32 X 1-3/4" Break Away 1-1/4"
1/2" Coupling Nut & 3" Rod 1-1/16" 8-32 X 1-3/4" Break Away 1-7/16"
3/4" Coupling Nut & 3" Rod 1-5/16" 8-32 X 1-3/4" Break Away No Cut
1" Coupling Nut & 3" Rod 1-9/16" 8-32 X 2-1/2" 2"
1-1/4" Coupling Nut & 3" Rod 1-13/16" 8-32 X 2-1/2" No Cut
1-1/2" Coupling Nut & 3" Rod 2-1/16" 8-32 X 2-3/4" No Cut
Product Specifications
• Wireless Frequency
2.4GHz, IEEE 802.15.4, using
AES 128-bit encryption
• Lock Battery Type AA Lithium, 1.5 Volts (V)
• Battery Life 50,000 cycles*
*All battery life claims are approximate and based
on a set configuration profile. Battery performance
is based on pre-defined system settings such
as battery chemistry and battery model used,
credential presentation settings (LED/buzzer),
UHF polling period, UHF status intervals, and
operations per day. Actual battery performance
will vary and depends on the factors above.
• Holding Force 400 lbs
• Operating Temperature
32° to 122° F (0° to 50° C)
• HID®multiCLASS SE®technology
Credentials Supported:
• High Frequency (13.56 MHz):
»HID iCLASS®
»HID iCLASS SE®(SIO-enabled)
»HID iCLASS®Seos™
»HID MIFARE®SE
»HID DESfire®EV1 SE
»MIFARE CLASSIC
»DESfire®EV1
• Low Frequency (125 kHz):
»HID Prox®, AWID, EM4102, ioProx
• NFC/BLE*
»Mobile – enabled credentials
*Supported on BLE-enabled models
3 of 12

Prepping
the Cabinet/
Drawer Face
1. Separate Strike Plate Template.
2. ESTABLISH CENTERLINE (for
double door cabinet see Double
Door Prepping, next page).
3. MEASURE cabinet wall thickness
and mark offset line on face of
cabinet/drawer. The offset line
should match with the interior
edge of the cabinet wall.
4. CONTINUE CENTERLINE to
the face of cabinet/drawer.
5. ALIGN template to offset
line and centerline. Remove
backing an apply template
onto cabinet/drawer face.
6. Use punch to mark drilling
locations, then drill mounting
holes. If using mechanical
Key override, drill key
override hole as well.
Diagram 3: Installation Template
Strike Plate
Template
Diagram 4: Prepping
CTR Line
Offset Line
4 of 12

Double Door
Prepping
1. Establish centerline on
inside of stationary door.
2. Continue centerline onto
outside face of cabinet.
3. Align offset line on template
to the edge of the stationary
door and align centerline above.
Remove backing and apply
template to cabinet face.
4. Use punch to mark drilling
locations, then drill mounting
holes. If using mechanical
Key override, drill key
override hole as well.
Diagram 5: Double Door Prep
CTR Line
Offset Line
& edge of
stationary
door
5 of 12

Installing Batteries
1. Install AA lithium batteries
in appropriate position.
2. Install cover and secure
using 2x Screw A.
Reader Installation
1. ALIGN reader with mounting holes and
pull cable through as shown. Trim the
threaded rod to length as outlined in
Mounting Screw Length table on page 3.
2. ADD Threadlock to threaded rod.
Secure Reader to cabinet/drawer
using the cut threaded rod and
coupling nut. DO NOT over tighten.
Diagram 6: Reader Installation
Diagram 7: Installing Batteries
6 of 12

Lock Body
Installation
1. INSERT reader cable through
hole in back of lock body.
2. ALIGN lock body to mounting
holes and secure to cabinet/
drawer face using 2x screw
fand 2x screw d. DO NOT
over tighten. If required use
Screw eor g, instead of f.
3. PLUG cable into slot on lock body.
4. Tuck excess cable into lock body
cavity as shown in Diagram 9.
5. For cabinet/drawer face thicker
than 1/2", add a third Screw d
as shown in Diagram 10.
Diagram 8: Step 1 & 2
Diagram 9: Step 3 & 4
Diagram 10: Step 5
7 of 12

Mechanical
Override
1. SLIDE Override into slot as
shown in Diagram 11.
2. ENSURE that override retracts
latch bolt before installation.
Override should rest loosely
until lock body and battery
cover are installed.
Mechanical Key
Override
Mechanical key override
cam lock sold separately.
1. INSERT CAM LOCK through the
outside of the cabinet/drawer
face and secure with locking nut.
2. INSERT the end of Cam into the
mechanical override and secure
with nut as shown in Diagram12.
OPTIONAL
OPTIONAL
IMPORTANT NOTE
Reader MUST be programmed before
installing the strike plate. If the cabinet is
closed before the reader in programmed
and after the strike plate is installed,
you will be locked out of the cabinet.
Diagram12: Mechanical Key Override
Diagram 11: Mechanical Override
8 of 12

Strike Plate
Installation
1. ALIGN strike plate template
to centerline and edge of
cabinet. Drill mounting holes.
2. SECURE strike plate to inside
cabinet wall using 2x Screw d,
BUT DO NOT FULLY TIGHTEN.
Adjust strike plate so the
edge is flush with the cabinet
wall edge then tighten.
3. After the strike plate is in
the desired position, fasten
Screw d into strike plate as
shown in Diagram 15.
Double Door
Strike Plate
Installation
1. ALIGN double door bracket
with mounting holes from
the strike plate template.
2. Secure strike plate to the double
door bracket using 3x Screw d
as shown in Diagram 16.
Diagram13: Strike Plate Template Use
Diagram16: Double Door Strike Plate Installation
Diagram14: Strike Plate Installation Diagram15: Step 3
9 of 12

LED Codes
Aperio LED LOCK Codes
(1) ONE Yellow Flash Card read
(1) ONE Green Flash Access Granted
(5) FIVE Yellow (1) ONE Red Force Closed
(in open mode)
Continuous Yellow Flashes
(.25 sec every second) Comhub busy
(1) ONE Red Flash Access Denied
(AC Online)
(3) THREE Red Flash Access Denied
(AC Of f line)
Continuous Red Flashes
(.125 sec every second) Lock is Blocked
(when closing)
(10) TEN Red Flashes Error in Lock
Continuous Yellow Flashes
(.25 sec every 5 seconds) Low Battery
Continuous Red Flashes
(.25 sec every 5 seconds) Dead Battery
Aperio LED HUB Codes
Steady Green Online
Steady Green
+ (1) ONE
Red Flash
Lock Offline
Steady Green
+ (2) TWO
Red Flashes
Access Control
Offline
Steady Green
+ (3) Three
Red Flashes
Access Control
& Lock Offline
Flashing
Yellow UHF
Communication
Aperio Hub Specifications
• Approvals CE, ETL, FCC, IC, C-Tick
• Safety & Emissions
FCC 47CFR Part 15 subpart B and subpart C;
IC RSS-210 EN ETSI 301 489-17 v2.1.1; ENETSI
300 328 v1.7.1; EN 60950-1 ed.2 2007
• Dimensions 82mm x 82mm x 37mm
• Power Supply 8-24 VDC
• Current 250 mA minimum
• Internal Antenna 2 cross polarized dipoles
• External Antenna (Part No. EXT-10-ANT)
One reverse polarity SMA external antenna
connector. Optional antenna type dipole
with max antenna gain of 3.9dBi
• Radio Standard IEEE 802.15.4(2.4GHz)
– 15 channels (11-25)
• Encryption (RadioCommunications)
AES 128 bits
• Wireless Operating Range Up to 50 ft
• Receiver Sensitivity
-100dBm 20% PER
• Wireless Transmit Power 10 d Bm/MHz
• Class of Protection IP 20
• Operating temperature
41°F to 95°F [5°C to 35°C]
• Humidity < 95% non-condensing
• Status LED (red/green/yellow)
10 of 12