Assa Abloy Corbin Russwin FE6600 Series User manual

FM468 03/20
Installation Instructions
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information
go to www.P65warnings.ca.gov.
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
FE6600 and
BL6600 Series
Standard Levers
Multi-Point Lock

2
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM468 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
1 Tools Required
#2 and #3 Phillips Screwdrivers Flat Blade Screwdriver 1/8" Allen Wrench
TOC Table of Contents
1 Tools Required ..................................................................2
2 Package Contents ...............................................................3
3 Installation ......................................................................4
a Change Hand of Lock ............................................................4
b Change Hand of Latch ...........................................................4
c FE6600 and BL6600 Series Multi-Point Locks .....................................5
d CE, RE1, RE3, L and LW Escutcheons ..............................................6
e RE2 and RE4 Escutcheons ........................................................6
f N Escutcheons ...................................................................7
g M Security Escutcheons..........................................................7

3
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM468 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
2 Package Contents
Figure1
1
16 12
15
14
14
15
16
13
8
8
18
11
17
6
5
319
22
2
21
20
6
7
9
19
3
22
10
4
Figure1 Description Qty. Figure1 Description Qty.
1 Inside Lever Handle - consult factory 1 12 Turn Lever Assembly (130KB design) -
2 Handle Set Screw 1/4-28 UNF 1 13 Emergency Button Assembly (184KB) 2
3 Rose - LN design 2 14 Backplate 1
4 Machine Screw #8-32 x 5/8" 2 15 Machine Screw (#6-32 x 3/8") 2
5 Inside Adapter and Plate Assembly 2 16 Machine Screw (#6-32 x 1/4") -
6 Spindle 1 17 KB Cylinder Rosset (for 8200) 1
7 Cap Nut 1 18 Compression Spring -
8 Washer 2 19 Non-loosening Wave Spring -
9Adapter and Plate Assembly
(LN design) 1 20 Lockbody 1
10 Mounting Post 2 21 Outside Front 1
11 Outside Lever Handle - consult
factory 1 22 Machine Screw (#8-32 x 1/4") 2
Note:
All trim components vary by function number. Refer to separate instruction sheet for
trim one-side functions.

4
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM468 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
3 Installation
a Change Hand of Lock
Note:
Red surface of locking piece must face secure
(keyed/locked) side of door.
To rotate locking piece:
1. Position lockbody with red surface of locking
piece visible.
2. Insert flat blade screwdriver into locking piece
slot to rotate locking piece.
3. Push locking piece toward back of lockbody
and rotate 180° until red surface shows on
opposite side.
Note:
Red color indicates locked side of door.
Figure2
Locking Piece Slot
b Change Hand of Latch
Note:
Beveled surface of latch must face strike. Deadlatch is self-adjusting.
To change hand of latch:
1. Insert flat blade screwdriver into spade
shaped slot. (Figure3)
2. Rotate screwdriver 90º to push latch out until
back of latch clears lock front; rotate latch
180º. Latch will re-enter lockbody.
Figure3
Spade
Shape Slot
Figure4
Latch
Lock Front
Figure5
Door Handing
Inside
Outside
Left Hand
Left Hand
Reverse Bevel
Right Hand
Right Hand
Reverse Bevel
Outside
Door hands determined from outside (Secured/Keyed side)
Inside

5
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM468 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
3 Installation (continued)
c FE6600 and BL6600 Series Multi-Point Locks
Important:
Check template 4740 to prep door for function holes, size and location.
1. Verify strike location according to template.
2. Clean out door pocket and door edge of debris.
3. Make sure handing of lock (latch and locking piece)
match handing of door.
4. Slide lock into door and hold.
5. Slide outside lever and rose assembly (or lever and escutcheon
assembly) through the door; lockbody and hold.
Note:
• Keep door open while installing lock. If installing lever onto
only one side of the door, see separate instruction sheet.
• Assemble keyed cylinder through narrow end of spring
and wider opening of collar (or escutcheon).
• Assemble onto door by threading into lock until cylinder face is flush
with collar edge. Pulling key slightly out of cylinder will help when
threading cylinder inward.
Note:
Corbin Russwin logo must be horizontal and on upper portion of cylinder face.
6. Tighten cylinder clamp screw (#2 Phillips screwdriver).
7. Secure lock in door with two (2) wood screws (#12 x 1-1/4") or machine screws (#12-24 x 1/2").
Do NOT tighten completely at this time.
8. Slide spindle into lockbody hub.
9. Slide adapter and plate assembly over spindle and secure
with two (2) #8-32 screws.
10. Screw rose firmly onto adapter and plate assembly
(or attach escutcheon).
11. Attach inside lever and secure with 1/8" Allen wrench.
Verify lock is operating correctly prior to closing door.
12. Assemble thumbturn/emergency release (if provided)
according to instructions on bag.
13. Check for proper lock operation prior to closing door.
14. Tighten two (2) lockbody screws completely. Attach outside
front using two (2) #8-32 x 1/4" flat head screws.
Note:
Removable core or interchangeable core cylinders require a control key (key stamped with C) to remove
and install the inner cylinder core.
• This is not standard and must be requested separately.
• If requesting 1-bitted control key, specify 113511 cut.
Figure6
Outside of Door
RH Door Shown
1
2
3
Figure7
4
78
6
5
Outside of Door
10
9
13
Figure8

6
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM468 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
3 Installation (continued)
d CE, RE1, RE3, L and LW Escutcheons
Through-bolt inside escutcheon to outside
escutcheon with two (2) screws #8-32 x 1-7/8"
(Figure 9, item #1).
Notes:
• Screw heads should be visible on inside
escutcheon.
• Removable core or interchangeable core
cylinders require a control key (stamped with
C) to remove and install the inner cylinder
core.
• This is not provided standard ; must be
requested separately.
• If requesting 1-bitted control key, specify
113511 cut.
Inside
of Door
Cylinder
Collar*
Outside
of Door
Figure9
1
*Cylinder collar(s) required for functions with two (2) cylinders or cylinders
longer than # 41 (1-1/8"). (Figure9)
e RE2 and RE4 Escutcheons
Notes:
• RE4 is designed for concealed cylinders.
• Concealed cylinders are installed prior to
attaching escutcheons.
1. Outside escutcheon must be through-bolted
with items K and L (Figure 10) prior to
attaching inside escutcheon.
2. Position inside escutcheon over item L and
secure with set screw (item J) using 1/8" Allen
wrench.
Note:
Cylinder collar(s) required for functions with two
(2) cylinders or cylinders longer than #41 (1-1/8").
(Figure10)
Figure10
Set Screw

7
FE6600 and BL6600 Series
Installation Instructions
Multi-Point Lock
FM468 03/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
3 Installation (continued)
f N Escutcheons
Inside and outside escutcheons are surface-
applied with eight (8) #6 x 3/4" wood screws or
eight (8) #6-32 x 3/4" machine screws. (Figure 11)
Note:
Cylinder collar(s) required for functions with two
(2) cylinders or cylinders longer than #41 (1-1/8").
Wood or
Machine
Screws
Inside
of Door
Figure11
Wood or
Machine Screws
Wood or Machine Screws
Outside
of Door
Wood or
Machine
Screws
g M Security Escutcheons
1. Cylinder installs under escutcheon.*
2. Through-bolt inside escutcheon to outside
escutcheon with four (4) 1/4-20x1-3/8"
screws.
Note:
Screw heads are visible on inside escutcheon.
3. Back cylinder out toward escutcheon as far as
possible.
4. Secure cylinder in lockbody. (Figure 12)
* Double cylinder functions:
• Include a supplied cylinder retaining cap.
• Install both cylinders and place retaining cap
and escutcheons over each.
• Back cylinder out toward escutcheon as far as
possible. (Figure13)
Figure12
Figure13

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.
Copyright © 2017, 2019, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Corbin Russwin, Inc.
225 Episcopal Road
Berlin, CT 06037 USA
Phone: [phone]
Fax: [phone]
www.corbinrusswin.com
FM468 03/20